Nb-Anl/Off; Rf.gain.control; Program.memory.channels - Cobra 29 LX How To Use Manual

Operation

NB-ANL/OFF

NB-ANL/OFF (Noise Blanker/Automatic
Noise Limiter) Button
(Noise Blanker /
Automatic Noise
Limiter) Button
Note
The RF noise blanker is very
effective in reducing repetitive
noises such as ignition interfer-
ence.
1
. . W hen.switched.to.ANL.the.Automatic.Noise.
.
.
RF Gain Control
RF Gain Control
The.RF.Gain.is.used.to.optimize.reception.in.
strong.or.weak.signal.areas..
Note
The RF Gain is used to optimize
reception in weak signal areas.
1
26
NB/ANL
2 3
NB/ANL 1.5
SWR CAL
TX
ANL
RX
S/ RF
S/RF
RF
NB/ANL
3 5 7 9
1
SIG +30dB
SWR /CAL
S/RF
VOL SQ DYNAMIKE
SWR/CAL
Limiter.is.activated..This.helps.reduce.noise.
created.by.the.vehicle's.electronics.
OFF MIN
. W hen.switched.to.NB/ANL.mode.the.RF.Noise.
Blanker.is.also.activated,.providing.increased.
noise.filtration.
NB/ANL
. W hen.switched.to.OFF.mode.all.noise.
filtration.will.be.turned.off.
S/RF
SWR/CAL
VOL
OFF
NB/ANL
NB/ANL
ANL
S/RF
S/RF
RF
SWR
CAL
SWR/CAL
VOL SQ
Rotate.the.RF.Gain.knob.counterclockwise.to.
reduce.gain.in.strong.signal.areas..In.weak..
OFF
signal.areas.turn.clockwise.to.increase.gain.
Program Memory Channels
Set.first.channel..Press.and.hold.Scan/MemScan.
button..Memory.icon.will.appear..Select.second.
channel,.press.and.hold.Scan/MemScan.button.
again.until.Memory.icon.appears..Repeat.above.
steps.to.enter.up.to.10.channels.in.memory.
2 3
NB/ANL 1.5
SWR MEM WX ! CAL
TX
ANL
RX
S/RF
RF RF GAIN DELTA TUNE
SWR
CAL
3 5 7 9
1
SIG +30dB
VOL SQ DYNAMIKE
MIN MAX
OFF MIN
1.5 2 3
NB/ANL CAL
SWR
TX
ANL
RX
S/RF
RF
SWR
CAL
3 5 7 9
1
SIG +30dB
MEM
SQ DYNAMIKE
. . P ressing.the.Scan/Memory Scan.button.
1
toggles.from.Off.to.Scan All Channels.to.
MIN
Memory Channel Only Scan.and.back.to.Off..
2 3
1.5
CAL
SWR TX
.
RX
3 5 7 9
1
SIG +30dB
MEM WX !
.
DYNAMIKE
.
. Press.Dim/Escape.button.to.end.Scan.and..
2
. return.to.CB.mode.
MIN
MIN
CH 9/
SCAN
19
MEM SCAN
ESC
CH 9/
SCAN
19
MEM SCAN
SWR
T BACK
CAL
ESC
MEM
SWR
RF GAIN DELTA TUNE T BACK
CAL
OFF
MIN MAX OFF
CH 9/
SCAN
19
MEM SCAN
ESC
WX !
SWR
RF GAIN DELTA TUNE T BACK
CAL
MIN MAX OFF
CH 9/
SCAN
19
MEM SCAN
ESC
SWR
RF GAIN DELTA TUNE T BACK
CAL
MAX OFF
Operation
Program Memory
Channels
Note
The radio should be
squelched before scan
features are activated.
Note
Keying the microphone will
stop the scan feature.
Note
If more than 10 channels are
attempted to be programmed,
3 error beeps will be heard and
"Memory Full" will be displayed
for 10 seconds or until any
button is pushed.
Note
To remove a channel from
memory, go to the unwanted
memory channel then press
and hold the scan button until
the MEM icon turns off.
Note
If in WX mode the unit will
scan Weather channels.
27