1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. AR-C150
  6. Service manual

Sharp AR-C150 Service Manual

Digital full color copier
Hide thumbs Also See for AR-C150:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
[ 3 ] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[ 4 ] SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[ 7 ] SETTING AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
Installationsanleitung
DIGITAL FULL
COLOR COPIER
MODEL
CONTENTS
CODE: 00ZARC150/F1E
AR-C150
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
AR-C150

Advertisement

Table of Contents
loading

Related Manuals for Sharp AR-C150

Summary of Contents for Sharp AR-C150

  • Page 1 AR-C150 CODE: 00ZARC150/F1E Installationsanleitung DIGITAL FULL COLOR COPIER AR-C150 MODEL CONTENTS [ 3 ] CONSUMABLE PARTS ....... 3-1 [ 4 ] SETUP .
  • Page 2 AR-C150 AR-C150 Supply List (Europe, Australia, New Zealand) DIMENSIONS LIFE (W × D × H): mm NAME CONTENT(S) Model INCOMPATIBILITY REMARK Note 1) /WHIGHT: kg × 10 4K Note 1) 329 × 590 × 218/5.62 (AR-C15T6) × 10 = 1 Color Toner (cyan) "Toner Cartridge (cyan) (267g),...
  • Page 3 AR-C150 B. Consumable parts required for setup Name Outside Japan Oil bottle AR-C15SL Developer cartridge (Y) Color developer kit Developer cartridge (M) (Y, M, C) Developer cartridge (C) Black developer (K) Developer cartridge (K) Developing unit AR-DW1 (Developing unit × 4)

  • Page 4: Lock Release

    AR-C150 Operation Manual kit A. External fitting section 1) Remove the fixing tape and packing material from the copier body. Language Model name Content Note English AR-150SE Operation Manual (Bound 25 sets together with Key Operator Germany AR-150SG Guide), Operation panel...

  • Page 5: Transfer Section

    AR-C150 4) Loosen the blue screw (1), and remove the process frame cover C. Transfer section (2). 1) Open the front cover (1), and remove the toner hopper unit (2). 2) Remove the toner hopper connector cover (3) in section A and remove the connector (4).

  • Page 6: Main Charger

    AR-C150 7) Remove the unit fixing screw B (1) and the unit fixing screw A (2). E. Paper feed, paper transport section 1) Remove the rotating plate fixing material of the paper feed tray, and remove the caution label. 5. Cleaning A.

  • Page 7: Document Table

    AR-C150 7) Install the electrode section to the original position, and fix it with 6. Consumable parts setup the fixing screw. A. Fusing oil setup 1) Remove the cap (1) from the oil bottle (2), and remove the inner cap. Set the cap (3) again.
  • Page 8 AR-C150 4) Pull out the transfer unit, cover the whole surface of the transfer B. Developer setup belt with paper, and insert the transfer unit. At that time, keep (1) Developer setup the lock handle released. This procedure is performed in order to...
  • Page 9 AR-C150 8) Set the developer cartridges in the sequence of black, cyan, 5) Clear the developer counter with SIM 24-5. magenta, and yellow. 6) Execute SIM 44-27 to reset the half tone correction data (correc- 9) Put the developer cartridge on the developer unit pawl A, and tion conditions) to the default level.
  • Page 10 AR-C150 5) Tap the toner cartridge top 5 times, and shake it horizontally 20 11) Tap the toner cartridge top several times. times. 12) Drop the toner attached to the inside of the toner cartridge com- pletely. 5 times 20 times 6) Attach the toner cartridge to the toner box to be refilled.

  • Page 11: Paper Setup

    AR-C150 • (Note) When a tray is pulled out during copying, a paper jam may D. Paper setup occur. When a paper jam occurs in the tray, if the tray is 1) Push down the lock lever until it stops to release the tray lock.
  • Page 12 AR-C150 2) Remove the cabinet fixing screw. 3) Pass the washer of the horizontal level check string into the screw (LX-BZ0870FCZZ) and attach it to the copier. 4) Check that the horizontal level check string is in the frame mark of the horizontal level check sheet.

  • Page 13: Function And Operation Check

    Used to set options. (When installing an option, use this justment data can be directly inputted efficiently. simulation to set the option (software). (AR-C150 only) 1) Used to set the paper size of the large capacity tray. 12. Procedures for transit (When the paper size is changed, this simulation must be executed to change the paper size in software.)

  • Page 14: Setting And Adjustments

    AR-C150 2) Enter the SIM 63-7 mode. [7] SETTING AND ADJUSTMENTS 1. List of setup items Related Set item simulations SET M1 Auto color balance adjustment target setup 46-21, 63-7, 63-8 SET M2 Auto color balance adjustment target 63-8, 46-24 selection 3) Press the SETUP key.

  • Page 15: List Of Adjustment Items

    AR-C150 NOTE: This setup is performed only when the user understands the SET M2 Auto color balance adjustment target copy color balance and the auto density adjustment and is selection capable of performing the operation. There are following two kinds of targets, and one of them can be Full explanations on the operating procedure, notes, and selected.)
  • Page 16 AR-C150 ADJUSTMENT ITEM SIMULATION ADJ M16 "Image position, image loss, void area 50-1/50-2 adjustment" ADJ M17 Image quality adjustment ADJ 1 CCD gamma adjustment 63-3 (63-5) ADJ 2 Image color balance adjustment (Auto) 46-24 ADJ 3 Image color balance adjustment (Manual) 46-21 46-10 ∼...
  • Page 17 AR-C150 4) Loosen the resist roller fixing screw, and change the resist roller 7) Check that the SIM 44-13 values are within the specifications. angle. Check content Spec PCLEDC (Sensor current in color calibration) 128 or below DARK ID (Color image density sensor dark...
  • Page 18 AR-C150 4) If the image is distorted, loosen the red screw for the holder on the ADJ M7 Image skew adjustment (Scanner chassis side, and adjust the LSU inclination with the black LSU (Writing) unit) adjustment screw (set screw). (The LSU at the right end is black.)
  • Page 19 AR-C150 Compare the positions (front-rear) of the same color Compare the positions (front-rear) of the same color print patterns. Procedures 1) – 4) : Adjustment procedures of the black LSU Procedures 5) – 7) : Adjustment procedures of the color LSU...
  • Page 20 AR-C150 5) Check the deflection cycle of 125.6mm pitch of four printed pat- If the above procedures cannot bring a satisfactory result, select terns (C, M, Y). Use the output pattern of the smallest deflection mode 1 and print twelve pages of the print pattern.
  • Page 21 AR-C150 ADJ M9 Main scanning direction copy magnification ratio adjustment (Scanner (Writing) unit) Main scanning direction image registration adjustment (Scanner (Writing) unit) ADJ 1 Main scanning direction copy magnification ratio adjustment (Scanner 2) Select the paper feed cassette of A3 (11" × 17") paper in the setup (Writing) unit) (Black) item H (PAPER SEL).
  • Page 22 AR-C150 If the rough adjustment pattern or the fine adjustment pattern is not in [How to read the pattern] the above range, perform the following procedures. When deflection is made to the positive (+) side in the rough adjust- 5) Calculate the shift from the adjustment reference position for each ment, increase the value on the positive (+) side.
  • Page 23 AR-C150 • 1) Enter the SIM 50-21 mode. Rough adjustment print pattern check 2) Select the paper feed cassette of A4R (8 1/2" × 11") paper in the Check that the rough adjustment print pattern is at the center of the rough adjustment reference pattern.
  • Page 24 AR-C150 [Sub scan registration adjustment pattern] (Example) Set the simulation set values as shown below. A: 100 A: 73 (=100 –27) → B: 112 B: 129 (=112 + 17) Set value C: 95 C: 110 (=95+15) 7 – 13...
  • Page 25 AR-C150 [How to read the pattern] When deflection is made to the positive (+) side in the rough adjust- ment, increase the value on the positive (+) side. When the deflection is made to the negative (–) side in the rough ad- justment, increase the value on the negative (–) side.

  • Page 26: Image Quality Adjustment

    AR-C150 ADJ M17 Image quality adjustment Copy color balance density check (Check in the TEXT/Photo mode.) START (Test chart UKOG-0162FCZZ/ UKOG-0283FCZZ is used.) Is the Perform ADJ1 CCD gamma copy color balance/ adjustment. Was CCD replaced ? density adjustment required ?
  • Page 27 2) Check that there is no dirt or scratch on BK1 and BK2 patches of Copy color balance and density check SIT chart (UKOG-0280FCZZ). Check the color balance and the density by making copies of Sharp If there is dirt, clean with alcohol. gray chart and the serviceman chart.
  • Page 28 AR-C150 While the automatic color balance adjustment by the serviceman al- lows adjustment even when the machine environment is changed lar- gely, providing normal color balance. If there is a basic problem in the machine, repair it and adjust to provide normal color balance.
  • Page 29 AR-C150 15) Use the test chart UKOG-0283FCZZ and check the copy color ADJ 3 Copy color blance adjustment (Manual) balance and the density in Text/Photo mode. (Refer to the This adjustment must be performed in the following cases: section of the copy color balance and the density.) •...
  • Page 30 AR-C150 Vorgehensweise zur Kopienqualitätseinstellung 1. SIM 63-3 (SIT Chart) oder - CCD Grundeinstellung SIM 63-5 (Standard Werte) 2. SIM 63-8 - Standard Scanner Target 3. SIM 46-24 - Auto Calibration Color Balance Falls die Kopienqualität nicht zufriedenstellend... 4. SIM 46-21 - Manual Color Balance oder SIM 46-10 bis 46-20 für jeden Kopiermodus extra.
  • Page 31 AR-C150 Special Tools List Tool Parts Code Price Code Note Color Test Chart UKOG-0283FCZZ A3 size, picture quality check Adjustment Sheet UKOG-0281FCZZ Image density sensor adj. For image density Sensor CCD adj. Chart UKOG-0280FCZZ CCD Gamma Adj. Chart Nip adj. Wrench UKOG-0282FCZZ Use for fusing pressure adj.

Table of Contents