Part Entry Time; Inputs; Zone Status; Zone Array - Bosch Solution 6000 User Manual

User Guide
Solution 6000
want to program the entry time for, then press
[OK] to select. Alternatively, you can enter the area
number that you want to program, then press [OK].
The keypad will display the following:
Entry Time 2 A1
040 Seconds
Press 0-9 OK to SAVE
3. Use the numeric keys to enter the required time in
seconds and then press [OK]. Entry time 2 can be set
from 0 to 255 seconds.
Areas > Timers >

Part Entry Time

This menu sets the time period which a keypad will sound
its warning tone after a zone is triggered in Part On or Part
2 On modes. The user must disarm the area before the Part
Entry Time expires, otherwise an alarm condition will be
triggered.
At factory default, when an area has been turned Part On
or Part 2 On and exit time has finished, violating a non 24hr
burglary zone will start the part entry time. The keypad
will sound the hi/lo tone for a period of 60 seconds before
the control panel sound an alarm or until the user turns the
area off.
The part entry time will start when any of the following
zone types area faulted and set to be monitored for Part
On or Part 2 On.
™ Burglary Delay 1
™ Burglary Delay 2
™ Burglary Instant
™ Burglary Inst No Exit
™ Burglary Handover
Only the installer or a master user can set the part entry
time for each area (001 to 255 seconds). Programming 001
seconds allows all non 24 hour burglary zones (including
delay zones) to act as if they were all instant zones when
the area is turned Part On or Part 2 On. Programming 000
seconds allows all non 24 hour burglary zones to operate
as they would if the area has been turned All On.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [8] + [3].
A list of available areas will display on the keypad.
A1 Reception Area
A2 Sales Dept
A3 Administration Dept
Press

2. Use the [] and [] keys to select the area that you
want to program the entry time for, then press
[OK] to select. Alternatively, you can enter the area
number that you want to program, then press [OK].
22
MENU 2-8-3
OK or MENU
The keypad will display the following:
Part Entry Time A1
060 Seconds
Press 0-9 OK to SAVE
3. Use the numeric keys to enter the required time in
seconds and then press [OK]. Part entry time can be
set from 0 to 255 seconds.

Inputs

Each panel can have up to a maximum 144 zones. When
the optional radio receiver is fitted any available zone
may be programmed as a wireless zone. Your installer will
advise you on the exact makeup and configuration of your
system.
Inputs > Commands >

Zone Status

This menu allows you to view the zone status of each zone
(i.e. Normal, Open or Short).
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [3] + [0] + [0].
A list of different zones will display on the keypad.
2. Use the [] and [] keys to select the zone that you
want to turn view the status information then press
[OK] to select. Alternatively, you can enter the zone
number that you want to view status information,
then press [OK].
The keypad will display the following zone status
information:
Zone 1 Name Zn1
EOL=Normal 06523 ohms
Press OK or MENU
3. Press the [OK] key to exit.
Inputs > Commands >

Zone Array

This menu allows you to view zones in groups of sixteen.
The top two rows of the display show the zone number, the
third row displays the zone status
N= NORMAL
S = SHORTED
A= ALARM
T= TAMPER
- = DISABLED
If a 100 is displayed at the right hand side of the top line, it
means that you are displaying zones 97 to 112 or zones 113
to 128 etc. See example.
Enter programming mode (PIN + MENU) then,
Bosch Security Systems 12/14 BLCC610U
MENU 3-0-0
MENU 3-0-1