Chime On/Off; Chime Mode; Area Name - Bosch Solution 6000 User Manual

A1 Reception Area
A2 Sales Dept
A3 Administration Dept
Press

2. Use the [] and [] keys to select the area that you
want to move the keypad display to, then press
[OK] to select. Alternatively, you can enter the area
number that you want to move the keypad display
to, then press [OK].
Areas > Commands >

Chime On/Off

Chime mode allows you to monitor a zone (or group
of zones) and to sound the keypad buzzer or activate a
programmable output when the a zone programmed for
chime is open and the system is in the disrmed state. This
can be useful when you need to monitor the front or back
entrance to the premises.
This menu allows a user to turn chime mode on or off.
Only keypads programmed to sound the chime tone will
be heard when a zone programmed for chime is faulted.
The master user can set which zone are to be chime zones
via MENU 3-0-3. If no zones are programmed for chime
then chime mode will not activate.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [5].
A list of different areas will display on the keypad.
A1 Reception Area 
A2 Sales Dept
A3 Administration Dept
Press

2. Use the [] and [] keys to select the area that you
want to turn chime mode on or off, then press [OK]
to select. Alternatively, you can enter the area
number that you want to turn chime mode on or
off, then press [OK]. The keypad will display the
following when chime mode is turned off:
Reception Area A1
Chime is OFF.
To turn ON, Press ON.
To Go Back Press OK
The keypad will display the following when chime
mode is turned on:
Reception Area A1
Chime is ON.
To turn OFF, Press OFF.
To Go Back Press OK
Bosch Security Systems 12/14 BLCC610U
OK or MENU
MENU 2-0-5
OK or MENU
3. Press the [ON] key to turn chime mode on, or, press
[OFF] to turn chime mode off.
4. Press the [OK] key to exit.
Holding down the 4 key on the keypad for 2 seconds
i
will also turn chime mode on and off.
Note
Areas > Commands >

Chime Mode

This menu allows you to program how the chime alert
behaves when a chime zone is triggered. There are four
different modes available: - Chime Always, Chime After ???
Seconds, Chime For ??? Seconds and Latching.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [6].
A list of different areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the chime mode for, then press
[OK] to select. Alternatively, you can enter the area
number that you want to program the name, then
press [OK].
The keypad will display the following:
Chime Mode A1
Chime For 000 Seconds
Press

3. Use the [] and [] keys to scroll through the
different options available. If the mode selected
requires you to enter a time then use the [] and
[] keys to move to the time field and then use the
[] and [] keys to scroll through the available time
options.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Areas > Area Properties >

Area Name

This menu allows you to program the name for each
area. Each area name can be programmed with up to 20
characters. At factory default, only Area 1 is used. The
control panel can have a maximum of 8 independent areas
programmed.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [1] + [0].
A list of different areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the name, then press [OK] to
select. Alternatively, you can enter the area number
that you want to program the name, then press
[OK].
Solution 6000 User Guide
MENU 2-0-6
OK to SAVE
MENU 2-1-0
19