LG STB-3000 Setup Manual page 36

Installer Menu (Cont.)
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables ACK
feature of MPI.
031 - POLL RATE
MPI Communication Parameter. Selects poll rate for MPI. Step size
of 16 ms. Changing from default may affect communication via MPI.
032 - TIMING PULSE
MPI Communication Parameter. Sets baud rate for MPI. Step size
of 4.3 uS. Changing from default may affect communication via MPI.
035 - HDMI1 ENABLE
Set to 1 to enable HDMI 1 input in DTV Mode. Set to 2 to enable
HDMI 1 input in PC Mode. Set to 0 to disable display panel HDMI
1 input.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0
to disable display panel rear Aux (Video 1) input.
041 - SIMPLINK EN
Set to 0 to disable the SIMPLINK feature. Set to 1 to enable
SIMPLINK functionality (does not enable remote control access to
the SIMPLINK Menu).
Note: When both this item and item 042 AUTO INPUTS are
enabled in the Installer Menu, HDMI inputs will be detected by
SIMPLINK, but the Auto Input(s) Sensing Feature will not function.
042 - AUTO INPUTS
Determines the Aux inputs for which auto-sensing is enabled. Set
to 0 to disable auto-sensing for all available inputs. Set to 255 to
enable auto-sensing for all available inputs. For information on
options for individual input settings, see Reference section, "Auto
Input(s) Sensing Feature."
Note: In order for auto-sensing to be enabled for an input, that
input must also be enabled in the Installer Menu. For example, to
enable auto-sensing for HDMI 1, item 035 HDMI1 ENABLE must
also be set to 1 or 2. Also, see note above regarding STB operation
when both this item and item 041 SIMPLINK EN are enabled.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting Aux source. When turned ON, the STB/display
panel will tune to starting Aux source if item 004 STRT CHANNEL
is set to 0.
1 = Video 1 3 = HDMI 1
5 = HDMI 2 255 = Last Aux (default)
Note: Above is applicable only if all Aux sources are enabled.
Note: This item is not available in the Installer Menu unless item
004 STRT CHANNEL is set to 0.
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number
instead of channel 0. Set to 0 to disable Aux identification change.
Controls MPI status channel response for Aux inputs.
36
049 - DIS. AUDIO M. (Disable Audio Menu)
Determines the availability of the Sound Out (Audio) Menu in the
STB menus. Also determines the default Audio Mode when STB is
turned ON. See the table below and set as required.
Sound Out (Audio)
Value
Menu Status
0 (default) Enabled
1 Disabled
2 Enabled
3 Disabled
4 Enabled
5 Disabled
6 Enabled
7 Disabled
Note: If a SIMPLINK-enabled device is connected to the STB
and item 041 SIMPLINK EN is set to 1 (enabled), the SIMPLINK
device Audio Mode will have priority over the setting of this item
when the STB/display is turned ON.
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the STB's Channel-Time display; the STB's
Channel-Time display will not appear. Set to 0 to enable the STB's
Channel-Time display.
069 - EN. CH-T COL. (Enable Channel-Time Custom Color)
Set to 1 to enable custom color for the STB's Channel-Time display.
Set to 0 to disable custom color for the Channel-Time display.
070 - FOR. CH-TIME (Channel-Time Display Foreground Color)
Set the STB's Channel-Time display foreground color according
to the following color chart:
0 = Black 3 = Cyan
1 = Blue 4 = Red
2 = Green 5 = Violet
Note: If foreground color and background color are the same, the
menu background will be transparent.
Note: Applies only to "Channel Not Available" message if item
073 CH NOT AVBLE is set to 1 (enabled). Also, items 070 FOR.
CH-TIME and 071 BCK. CH-TIME are not available in the Installer
Menu when item 069 EN. CH-T COL. is set to 0.
071 - BCK. CH-TIME (Channel-Time Display Background Color)
See description for item 070 FOR. CH-TIME above. The color
chart is the same for both items.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CH. OVERIDE is set to 0, a "CHANNEL
NOT AVAILABLE" message is displayed when a user attempts to
direct tune a channel that is not included in the channel lineup.
Note: This item is not available in the Installer Menu when item
028 CH. OVERIDE is set to 1.
Default Audio Mode at TV
Turn ON
Internal Display Speaker
Internal Display Speaker
External Speaker (optical or HDMI)
External Speaker (optical or HDMI)
LG Sound Sync (optical)
LG Sound Sync (optical)
LG Sound Sync (BT wireless)
LG Sound Sync (BT wireless)
6 = Yellow
7 = White
206-4272