Sony SRX-R515P Installation Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Projector
  5. SRX-R515P
  6. Installation manual

Sony SRX-R515P Installation Manual

Digital cinema projector package
Hide thumbs Also See for SRX-R515P:
Table of Contents

Advertisement

Quick Links

DIGITAL CINEMA PROJECTOR PACKAGE
SRX-R515P
LENS CHANGE TABLE
LKRA-008
3D PROJECTION LENS
LKRL-A502
LKRL-A503
2D PROJECTION LENS
LKRL-Z511
LKRL-Z514
LKRL-Z519
PROJECTION LAMP
LKRM-U330
LKRM-U450
INSTALLATION MANUAL
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Sony SRX-R515P

Summary of Contents for Sony SRX-R515P

  • Page 1 DIGITAL CINEMA PROJECTOR PACKAGE SRX-R515P LENS CHANGE TABLE LKRA-008 3D PROJECTION LENS LKRL-A502 LKRL-A503 2D PROJECTION LENS LKRL-Z511 LKRL-Z514 LKRL-Z519 PROJECTION LAMP LKRM-U330 LKRM-U450 INSTALLATION MANUAL 1st Edition...
  • Page 2 Dette utstyret kan kobles til et IT-strømfordelingssystem. でください。 : NETWORK コネクター 上記のポートについては本書の指示に従ってください。 For safety, do not connect the connector for periph- eral device wiring that might have excessive volt- age to the following port. : NETWORK connector Follow the instructions for the above port. SRX-R515P...
  • Page 3 4. Prevention against achieving hazardous condition due to uneven mechanical loading When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading. 1 (P) SRX-R515P...

  • Page 5: Table Of Contents

    Connection with Projector .........3-4 (E) (FUNCTION MEMORY Function) ....5-23 (E) 5-7-7. Calling the Registered Image Information 3-3. Power Connection .............3-5 (E) (FUNCTION MEMORY Function) ....5-24 (E) 3-4. Power Cord ..............3-6 (E) 3-5. Installation of CRU DATAPORT Carrier ....3-6 (E) 1 (E) SRX-R515P...
  • Page 6 5-14-7. Creation of KDM Hot Folder......5-60 (E) 5-14-8. Retrieving the Certifi cate .......5-61 (E) 5-14-9. Alignment of the Screen Position of Each Image (R, G and B) .......5-62 (E) 5-14-10. Turning Off the Lamps Individually ....5-63 (E) 2 (E) SRX-R515P...

  • Page 7: Manual Structure

    . Windows and Windows 7 are the registered trademarks of Microsoft Corporation in the United States and Other countries. Other system names, product names, and company names appearing in this manual are trademarks or registered trademarks of their respective holders. 3 (E) SRX-R515P...

  • Page 9: Installation Outline

    (HDMI) USB 2.0 PCI-EX, LAN Digital cinema server (hereafter referred to as “Server”) Automation system GPIO Lighting controller Curtain controller RS-232C D-sub 9 pin Audio processor Theater network (LAN) Video signal, audio data USB 2.0/3.0 USB HDD 1-1 (E) SRX-R515P...

  • Page 10: Accessories

    [Digital Cinema Server XCT-S10] . Feet (1 set) . PCI express cable (2 m) (1) . Ethernet cable (2 m) (1) [Touch Panel Monitor LKRA-007] . AC adaptor (1) . VGA cable (1) . USB cable (1) 1-2 (E) SRX-R515P...

  • Page 11: Required Equipment/Tools

    . LKRL-Z511 . LKRL-Z514 . LKRL-Z519 . LKRL-A502 . LKRL-A503 Regarding the selection of lens, contact your local Sony Sales Office/Service Center. 3D lens filter LKRA-005 etc. Lens change table LKRA-008 For enabling easy replacement of the 2D lens and 3D lens.

  • Page 12: External Dimensions

    (Refer to the optional lens list.) Left side view Intake Air Intake Intake Input/output Heat terminal exhaust LKRL LIST LKRL REMARKS Z511 258-297 Z514 230-283 Z519 A502 Including in 3D lens filter A503 Including in 3D lens filter 1-4 (E) SRX-R515P...
  • Page 13 Top view Right side view Rear view Heat exhaust Air Intake Air Intake Air Intake Intake Air Intake Air Intake Heat exhaust Air Intake Bottom view 10-M8 (for fixing the projector) AC power cable Unit: mm 1-5 (E) SRX-R515P...

  • Page 14: Server

    1-4-2. Server Rear view Input/output AC power Heat exhaust terminal cable Heat exhaust Top view Front view Right side view Air Intake Unit: mm 1-6 (E) SRX-R515P...

  • Page 15: Installation Flow

    Install the lens change table as required. Install the lens change table. 6-1. Component (Refer to Section 6.) 6-2. Installation of Foot Assembly 6-3. Installation/Adjustment of 2D Unit Assembly 6-4. Installation/Adjustment of 3D Unit Assembly The installation is completed. 1-7 (E) SRX-R515P...

  • Page 16: Installation Of Carrying Handle

    1. Loosen the nut in the direction of the arrow A, then insert the handle arm in the direction of the arrow B. 2. Tighten the nut to fix the handle arm. 3. Attach the handle arm to the adjuster of other three portions by repeating steps 1 and 2. Adjuster Handle arm 1-8 (E) SRX-R515P...
  • Page 17 4. Insert the pipe (long) into the handle arms, then fix the pipe with the two M8 bolts. 5. Attach the pipe (long) on the other side in the same way. M8 bolts Handle arm Handle arm Handle arm Pipe (long) Pipe (long) 1-9 (E) SRX-R515P...
  • Page 18 1. Loosen the nut in the direction of the arrow A, then insert the handle arm in the direction of the arrow B. 2. Tighten the nut to fix the handle arm. 3. Attach the handle arm to the adjuster of other three portions by repeating steps 1 and 2. Adjuster Handle arm 1-10 (E) SRX-R515P...
  • Page 19 4. Insert the pipe (short) into the handle arms, then fix the pipe with the two M8 bolts. 5. Attach the pipe (short) on the other side in the same way. M8 bolts Pipe (short) Pipe (short) Pipe (short) 1-11 (E) SRX-R515P...

  • Page 21: Installation Of Projector

    Attach the 8-inch duct to the duct connecting portion on the rear side of the projector top portion. . When attaching the duct, be careful not to bend the duct for exhausting the air smoothly. . For the required exhaust air volume, refer to “1-3. Required Equipment/Tools”. 8-inch duct Rear side Duct connecting portion 2-1 (E) SRX-R515P...

  • Page 22: Installation Of Lens

    If you raise the lens fixing lever without pushing the lock button, the lock button and lens fixing lever will be damaged. Be sure to push the lock button and check that the lock is released before raising the lever. Lens fixing lever Lock button 2-2 (E) SRX-R515P...
  • Page 23 2. Attach the lens to the projector while firmly holding the lens not to drop it and aligning the position. When attaching the lens to the projector, insert it straight. 3. Lower the lens fixing lever to fix the lens. Lens Lens fixing lever Lens Lens fixing lever 2-3 (E) SRX-R515P...

  • Page 24: Installation Of 3D Lens Filter (In The Case Of Lkra-005)

    2. Attach the filter bracket (B) assembly with the two screws supplied with the 3D lens filter. Filter bracket (A) assembly PSW6 x 8 Filter bracket (A) assembly PSW6 x 8 PSW6 x 8 Filter bracket (A) assembly PSW6 x 8 Filter bracket (B) assembly 2-4 (E) SRX-R515P...
  • Page 25 3. Attach the 3D filter (R) assembly with the two knobs. Knob 3D filter (R) assembly Knob 2-5 (E) SRX-R515P...
  • Page 26 4. Release the lock plate in the direction of the arrow, then hook it on the position pin. 5. Attach the 3D filter (L) assembly with the two knobs. Knob Position pin Knob Lock plate 3D filter (L) assembly 2-6 (E) SRX-R515P...

  • Page 27: Installation Of Lamp

    1. Loosen the screw (with drop-safe), lower the two hooks, and then remove the intake grille (A) in the direction of the arrow A. Screw (with drop-safe) Hooks Intake grille (A) 2. Lower the lamp door latch to open the lamp door. Lamp door Lamp door latch 2-7 (E) SRX-R515P...

  • Page 28: Installation Of Touch Panel Monitor

    Connector contact portion 5. To install the intake grille (A), reverse the removal procedure. 2-5. Installation of Touch Panel Monitor 1. Attach the TPC mounting plate with the four screws. Touch panel monitor TPC mounting plate Screws 2-8 (E) SRX-R515P...
  • Page 29 (1) Remove the three screws. (2) Rotate the TPC arm block assembly in the direction of the arrow. (3) Fix the TPC arm block assembly with the three screws. PSW4 x 10 TPC arm block assembly PSW4 x 10 2-9 (E) SRX-R515P...
  • Page 30 4. Attach the touch panel monitor with the three screws. Touch panel monitor Screw Screw Screw 2-10 (E) SRX-R515P...
  • Page 31 (for service) (accessory) (To the AC adaptor) VGA terminal: VGA cable (accessory) (To the VGA terminal of the server) TPC terminal: USB cable (accessory) (To the TPC terminal of the server) Cable clamper Cable Cable clamper Knob 2-11 (E) SRX-R515P...

  • Page 32: Connection Of Power Cord

    1. Remove the four screws, then remove the terminal block cover. Terminal block cover Screws 2. Remove the screw, then remove the cable clamp. 3. Remove the screw, then remove the ground terminal. Ground terminal Screw Cable clamp Screw 2-12 (E) SRX-R515P...
  • Page 33 6. Route the power cord through the hole on the bottom of the terminal block, then fix each terminal with the screw as shown in the illustration. 7. Fix the power cord using the cable clamp and screw. 8. Attach the terminal block cover. Ground terminal Power cord Screws Screw Cable clamp 2-13 (E) SRX-R515P...

  • Page 34: Adjustment Of Projector Tilt

    . Rotate clockwise direction (2): To raise the height of projector . Rotate counterclockwise direction (3): To lower the height of projector 3. Fix the adjuster by tightening the nut toward the adjuster pipe. Example of tilted projector Adjuster pipe Adjuster 2-14 (E) SRX-R515P...

  • Page 35: Installation Of Server

    To reduce the temperature rise inside the server, keep at least 4 cm in the front and at least 10 cm in the rear between the rack and server. Required parts . Screw for rack mounting : 4 pcs The screws are not supplied with the product. Prepare the screws that match the rack. 3-1 (E) SRX-R515P...
  • Page 36 2. Loosen the two screws (with drop-safe), then remove the front panel assembly. Screw (with drop-safe) Front panel assembly Screw (with drop-safe) 3. Mount the server on the rack with the four rack mounting screws. Rack mounting screws Rack Server Rack mounting screws 3-2 (E) SRX-R515P...

  • Page 37: Placing The Server On The Pedestal

    Check that the pedestal is not unstable. B4 x 8 B4 x 8 Foot Foot holder B4 x 8 B4 x 8 B4 x 8 Foot Foot Foot holder Foot holder B4 x 8 B4 x 8 Foot Foot holder B4 x 8 3-3 (E) SRX-R515P...

  • Page 38: Connection With Projector

    3-2. Connection with Projector Left side of projector Ethernet cable PCI express cable (accessory) (accessory) Rear of server 3-4 (E) SRX-R515P...

  • Page 39: Power Connection

    If the power is not supplied correctly with UPS not used, the contents data can be broken. Bottom of touch panel monitor USB cable AC adaptor cable (accessory) (accessory) VGA cable (accessory) Rear of server Power cord AC adaptor USB cable Power cord (available on request) Rear of UPS 3-5 (E) SRX-R515P...

  • Page 40: Power Cord

    3-4. Power Cord To get a power cord, please contact your local Sony Sales Office/Service Center. . Use the approved Power Cord (3-core mains lead)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. . Use the Power Cord (3-core mains lead)/Appliance Connector/Plug conforming to the proper ratings (Voltage, Ampere).
  • Page 41 4. Remove the three screws, then remove the CRU cover. CRU cover PSW3 x 6 PSW3 x 6 CRU unit assembly 5. Remove the two screws, then remove the cover from the rear of the CRU DATAPORT carrier. Rear CRU DATAPORT carrier PSW3 x 6 Cover 3-7 (E) SRX-R515P...
  • Page 42 6. Connect the CRU DATAPORT carrier to the connector (CN12) on the IF-1180 board. IF-1180 board CN12 CRU unit assembly CRU DATAPORT carrier 7. Fix the CRU DATAPORT carrier with the three screws. PSW3 x 6 PSW3 x 6 CRU DATAPORT carrier 3-8 (E) SRX-R515P...
  • Page 43 9. Insert the CRU unit assembly into the server, then fix it with the two screws. When inserting the CRU unit assembly, be careful not to pinch the harness. CRU unit assembly Harness PSW3 x 6 PSW3 x 6 10. Attach the front panel. (Refer to step 4 in Section 3-1-1.) 3-9 (E) SRX-R515P...

  • Page 45: Connection With External Equipment

    Section 4 Connection with External Equipment 4-1. Projector 4-1-1. Connection Diagram Left side of projector AUDIO OUTPUT BAL AUDIO OUTPUT UNBAL External reproduction device Audio processor External reproduction device Audio processor HDMI cables Audio cables (AES) 4-1 (E) SRX-R515P...

  • Page 46: Connector Input/Output Signal

    * Connect the shielding wire of a cable to the shell so as to suppress radiation. AUDIO OUPUT UNBAL: D-sub 25 pin <External view> Pin No. Signal name Pin No. Signal name CH1/2+ CH3/4+ CH7/8+ CH5/6+ * Connect the shielding wire of a cable to the shell so as to suppress radiation. 4-2 (E) SRX-R515P...

  • Page 47: Server

    USB, HDD USB cable GPIO cable Theater equipment control system Theater equipment control system D-sub 25 pin (female) D-sub 25 pin (female) Rear of server Theater network (LAN) Audio processor Theater network (LAN) RS-232C cable Ethernet cables 4-3 (E) SRX-R515P...

  • Page 48: Connector Input/Output Signal

    OUT6 (COM) OUT6 (N/O) OUT15 (N/O) OUT5 (N/C) OUT5 (COM) OUT14 (N/O) +24 V OUT5 (N/O) OUT13 (N/O) +24 V +24 V * Connect the shielding wire of a cable to the shell so as to suppress radiation. 4-4 (E) SRX-R515P...
  • Page 49 AUDIO CTRL: D-sub 9 pin <External view> Pin No. Signal name * Connect to Audio Processor manufactured by Dolby. 4-5 (E) SRX-R515P...

  • Page 51: Setting And Adjustment After Connection

    The POWER indicator lights up in green. When the server is started, the “Login” screen is displayed on the monitor. Projector Server SYSTEM SW switch POWER indicator MAIN indicator Touch panel monitor IMB indicator LAMP indicator Power switch Example of Login screen 5-1 (E) SRX-R515P...

  • Page 52: Login

    1. Start up GUI. (Refer to Section 5-2 for how to use the GUI screen.) 2. Tap the “Configuration” tab. 3. Tap [User/Role]. The User/Role screen is displayed. [New] in the Users pane [User/Role] Screen example [New] in the Roles pane Users pane 5-2 (E) SRX-R515P...
  • Page 53 You may enter up to 50 characters (only alphanumeric). 3. Place a check mark in the item that you want to enable operation. There are items that can be selected for each Role Definition. 4. Tap [OK]. Type Role Name. [OK] [OK] 5-3 (E) SRX-R515P...

  • Page 54: About The Gui Screen

    . Status: Not used in this manual. . Error History: Used to obtain a log at the occurrence of error. Schedule tab Not used in this manual. 5-4 (E) SRX-R515P...
  • Page 55 . Projector (2D): Used for the adjustment of the 2D lens. . Projector (3D): Used for the adjustment of the 3D lens. . User/Role: Used for the addition or change of User or Role. 5-5 (E) SRX-R515P...

  • Page 56: Initial Setting

    1. Start up GUI. (Refer to Section 5-1-2.) 2. Tap the “Configuration” tab. 3. Tap [System] → [Server|Info]. The Server Info screen is displayed. [System] Screen example [Server|Info] [TPC|Calibration] 4. Tap [TPC|Calibration]. The TPC Calibration dialog is displayed. Screen example [Calibration] 5-6 (E) SRX-R515P...
  • Page 57 Perform this three times. (The place where the mark is displayed is changed.) When the last mark is tapped, the adjustment is completed, and then the display is returned to the Server Info screen. Tap the mark. 5-7 (E) SRX-R515P...

  • Page 58: Language Setting

    . English . Chinese 6. Set the display type of date in “Date” and time in “Time” as required. The display type of “Date” and “Time” varies depending on the language selected in step 5. 7. Tap [Apply]. 5-8 (E) SRX-R515P...

  • Page 59: Owner Information Setting

    Screen example [Server|Info] [Owner|Information] 4. Tap [Owner|Information]. The Owner Information dialog is displayed. Screen example [Apply] 5. Set “Owner”, “Organization”, “Region”, “Location” and “Screen” as required. There is no problem to set only arbitrary items. 6. Tap [Apply]. 5-9 (E) SRX-R515P...

  • Page 60: Date/Time Setting

    [Server|Info] [Date/Time] 4. Tap [Date/Time]. The Date/Time Setting dialog is displayed. Screen example 5. Set “Time Zone”. There is no problem to set only arbitrary items. 6. Set “Date” and “Time” in “Secure Clock Setting” as required. 5-10 (E) SRX-R515P...
  • Page 61 The clock on the screen (SMS Server Time) is set being synchronized with the clock of the NTP server (NTP Secure Time). “NTP Server” can be entered. The IP address of NTP Server can be entered. 8. Tap [Apply]. 9. When “Time Zone” is changed, restart the system manually. 5-11 (E) SRX-R515P...

  • Page 62: Performing The Marriage

    4. If “FAIL” is still displayed after 10 minutes have passed, take measures according to the following. . Only the “Marriage” column is Fail: Contact your local Sony Sales Office/Service Center. . “Door Closed” column is Fail: Check the installation of the cabinet of projector.

  • Page 63: Projector Startup

    (zoom), focus, image position, brightness) for the flat, scope and HD contents are performed, and then they are registered in the function memory respectively. After that, perform the color space conver- sion for the color space to be used. 5-13 (E) SRX-R515P...

  • Page 64: In The Case Of Using Only 2D Lens

    Adjust the brightness for each field angle of contents, and overwrite Select the color space mode “DCDM”. the function memory “2D SCOPE”, “2D FLAT” and “HD”. Register the setting data to the function memory as “2D SCOPE”. Call “2D FLAT” using the function memory. 5-14 (E) SRX-R515P...

  • Page 65: In The Case Of Using Only 3D Lens

    When the image is screened by 3D lens (without 2D lens screening), the procedure from “Perform the DCDM color space conversion for the right eye image and the left eye image. (Perform in the state without filter and 3D eyeglasses.)” is not required. 5-15 (E) SRX-R515P...

  • Page 66: Lens

    . [_]: Image is reduced. . [+]: Image is enlarged. 5. Adjust the focus with the Focus [_]/[+] in the Lens Control pane. . [_]: Image is focused on near point. . [+]: Image is focused on far point. 5-16 (E) SRX-R515P...

  • Page 67: Position Adjustment

    4. Adjust the image position in the horizontal direction by rotating the H shift knob. 5. Tighten the three V shift lock screws and three H shift lock screws. V shift lock screws (3 pcs) Lens shift V shift knob block H shift lock screws (3 pcs) H shift knob 5-17 (E) SRX-R515P...
  • Page 68 (scope, HD). . When you want to perform the H shift, adjust the image position with scope (horizontally longest field angle), then correct the image center position with other field angles (flat, HD). 5-18 (E) SRX-R515P...
  • Page 69 H shift When completely aligned: 0 % (no shift) When deviated by about 2 mm: 7% (Maximum adjustment range) V shift When completely aligned: 0 % (no shift) When deviated by about 5.5 mm: 35% (Maximum adjustment range) 5-19 (E) SRX-R515P...

  • Page 70: Position Adjustment (Electric Shift By Touch Panel)

    This adjustment is performed for adjusting the center position of image when zooming and so on in the case of using the V shift and H shift with the lens shift block. 1. Tap the “Configuration” tab. 2. Tap [Projector|$2D%] → [Set|Function]. The Set Function screen is displayed. [Projector|$2D%] Screen example [Set|Function] [Electric|Shift] 5-20 (E) SRX-R515P...

  • Page 71: Position Adjustment (Adjusting The Projector Tilt And Direction)

    Perform the mask processing because a keystone occurs when the projector is tilted. Mask processing 1. Tap the “Configuration” tab. 2. Tap [Projector|$2D%] → [Set|Function]. The Set Function screen is displayed. Screen example [Projector|$2D%] [Set|Function] [Masking|Adjust] 5-21 (E) SRX-R515P...

  • Page 72: Brightness Adjustment

    2. Select an appropriate luminance level from the three levels in the Lamp Power Control pane. n Level 3 is the brightest level. 3. Perform the fine adjustment using [+][_]. 4. Check the brightness using the luminance meter. Screen example Control Mode pane Lamp Power Control pane 5-22 (E) SRX-R515P...

  • Page 73: Registration Of Adjustment Result (Function Memory Function)

    3. Select the function memory that you want to register from Function List pane on the Projector (2D) screen, then tap [Save]. 4. Type the function name and tap [Apply]. The alphanumeric characters and symbols can be used as the function name (up to 32 characters). 5-23 (E) SRX-R515P...

  • Page 74: Calling The Registered Image Information (Function Memory Function)

    The Set Function screen is displayed. [Projector|$2D%] [Load] Screen example Function List pane [Set|Function] 3. Select the registered data that you want to call from the Function List pane. 4. Tap [Load]. The confirmation message is displayed. 5. Tap [OK]. 5-24 (E) SRX-R515P...

  • Page 75: Image Adjustment (3D Lens)

    1. Tap the “Configuration” tab. 2. Tap [Projector|$3D%] → [Set|Function]. The Set Function screen is displayed. [Projector|$3D%] Screen example [Set|Function] Test Pattern pane 5-25 (E) SRX-R515P...
  • Page 76 (magenta image) is projected from the upper lens by rotating the optical axis adjust- ment screw. 6. Tighten the four optical axis adjustment lock screws. (Tightening torque: 2.0 N.m) Optical axis adjustment screw Optical axis adjustment lock screws (4 pcs) The green light beam is output from the upper lens. 5-26 (E) SRX-R515P...

  • Page 77: Lens Filter Adjustment (In The Case Of Lkra-005)

    3D lens filter position (depth direction) adjustment 1. Loosen the knobs and position pins. 2. Move the 3D lens filters in the depth direction. 3. Tighten the knobs and position pins. Knobs Position pins Knobs Position pins 3D lens filters 5-27 (E) SRX-R515P...
  • Page 78 3D lens filter tilt adjustment 1. Loosen the two adjustment screws. 2. Tilt the 3D lens filter. 3. Tighten the adjustment screws. Adjustment screw (this screw is also attached on the other side.) 3D lens filter 5-28 (E) SRX-R515P...

  • Page 79: Zoom/Focus Adjustment

    Zoom ring (image for left eye) Zoom lock screw (image for left eye) Focus ring (image for left eye) Focus lock screw (image for left eye) The 3D lens filters are not shown in the illustration for the sake of clarity. 5-29 (E) SRX-R515P...

  • Page 80: Position Adjustment (Using The Lens Shift Mechanism, Only In The Vertical Direction)

    V shift lock screws (image for left eye) V shift lock screws (image for right eye) V shift adjustment screw (image for left eye) The 3D lens filters are not shown in the illustration for the sake of clarity. 5-30 (E) SRX-R515P...

  • Page 81: Position Adjustment (Adjust Image By Touch Panel)

    The Adjust Image screen is displayed. Screen example Adjust Position pane [Adjust|Image] 3. Tap the [Adjust] of the Adjust Position pane. The Adjust Position screen is displayed. Screen example 4. Adjust the image position in the horizontal direction. (H_Adjust) 5-31 (E) SRX-R515P...

  • Page 82: Position Adjustment (Adjusting The Projector Tilt And Direction)

    Tap the adjustment point and adjust H Adjust and V Adjust using the slide bar or [+][_]. . [+] : Setting value is increased. . [_] : Setting value is decreased. Tap [Reset] to return to the original masking amount. 5. Tap [Close] to close the Adjust Masking screen. 5-32 (E) SRX-R515P...

  • Page 83: Alignment Of The Horizontal Position Of Image

    The Adjust Image screen is displayed. Screen example Adjust Distortion pane [Adjust|Image] 3. Tap the [Adjust] of the Adjust Distortion pane, then adjust the position of the image for the right eye in the horizontal direction. Screen example 5-33 (E) SRX-R515P...
  • Page 84 (V Tilt) and the image shape in the vertical direction (V Bow) can be adjusted. In the case of increasing H Tilt (+) In the case of increasing V Tilt (+) In the case of increasing V Bow (+) 5-34 (E) SRX-R515P...

  • Page 85: Image Mapping

    1. Tap the “Configuration” tab. 2. Tap [Projector|$3D%] → [Set|Function]. The Set Function screen is displayed. [Projector|$3D%] Screen example [Set|Function] [Image|Mapping] 3. Tap [Image|Mapping]. The Image Mapping screen is displayed. Screen example 5-35 (E) SRX-R515P...

  • Page 86: Brightness Adjustment

    (level and fine adjustment value) that has been set). When the registered function memory is called, the lamp power value (level and fine adjustment value) is automatically adjusted so that the luminance becomes the same level as the luminance at that time. 5-36 (E) SRX-R515P...

  • Page 87: Registration Of Adjustment Result (Function Memory Function)

    3. Select the function memory that you want to register from the Function List pane, then tap [Save]. 4. Type the function name and tap [Apply]. The alphanumeric characters and symbols can be used as the function name (up to 32 characters). 5-37 (E) SRX-R515P...

  • Page 88: Calling The Registered Image Information (Function Memory Function)

    . In the case of using the 3D lens, perform the adjustment for the lower lens (image for left eye) and upper lens (image for right eye) respectively. Hide the image from view on the unadjusted side using the Picture Muting pane. Required equipment . Color meter/luminance meter . Tripod 5-38 (E) SRX-R515P...
  • Page 89 10. Check that all differences between respective values and values in the Target Color Gamut pane are less than ?0.002. 11. If there is any item having the difference of ?0.002 or more, perform steps 5 to 10 again. 5-39 (E) SRX-R515P...

  • Page 90: Check Of Video Signal And Audio Output

    2. Tap the “Configuration” tab. Tap [Projector|$2D%] or [Projector|$3D%] → [Set|Function]. The Set Function screen is displayed. (The screen example shows 2D screen.) Screen example [Projector|$2D%] [Set|Function] Input Channel pane 3. Set to the IMB Input using the Input Channel pane. 5-40 (E) SRX-R515P...

  • Page 91: Network Setting

    . Extended Settings/Audio Processor: Enter the IP address of the audio processor when connecting with an audio processor through LAN. Tap [Apply] after you have entered each IP address. 5-41 (E) SRX-R515P...
  • Page 92 1. Tap [New] in the Other Auditorium pane. The New Auditorium screen is displayed. Screen example [OK] 2. Select the Auditorium number and enter the IP address of the projection system to be connected. 3. Tap [OK]. 5-42 (E) SRX-R515P...

  • Page 93: Folder Setting

    To change setting, select a folder in the Source List pane and tap [Edit] after you have changed the set- ting. To delete an external folder, select a folder in the Source List pane and tap [Delete]. 5-43 (E) SRX-R515P...
  • Page 94 IP address of an FTP server . Server Port: Port number of an FTP server (Usually, set to 21.) [Source Access Information pane] . Domain: No entry is required. . Username/Password: Enter the user name and password of an FTP server. 5-44 (E) SRX-R515P...

  • Page 95: Setting Of External Equipment

    LMT300 or XCT-S10 Set the Sony digital cinema server (LMT-200, LMT-300 or XCT-S10) to be connected in the theater network (LAN). It can be used to ingest DCP. . Name: Specify the name of an external folder. . Storage Type: LMT300 or XCT-S10 (Select LMT300 when connecting with LMT-200.) .
  • Page 96 6. Press the [Esc] key on the USB keyboard, enter “:wq”, and press the [Enter] key. The contents of change are saved and the edit mode is terminated. 7. Execute the command below to reboot this system. #reboot 8. Remove the USB mouse and USB keyboard. 5-46 (E) SRX-R515P...

  • Page 97: Registration Of Ups

    Add the bold-faced portion as described below according to the type of UPS to be used. . When using UPS made by APC: com.sony.dcinema.upsMgr.impl.Apcupsd . When using UPS made by TrippLite: com.sony.dcinema.upsMgr.impl.TrippLited 3. Save the changed contents and end the registration. (Refer to steps 6 to 8 in Section 5-13-1.) 5-13-3. Registration of Audio Processor When this server and an audio processor are connected using RS-232C or a LAN cable, the volume can be controlled and muted from this unit to the audio processor.

  • Page 98: Setting Of Gpio

    1. Tap the “Configuration” tab. 2. Tap [System] → [GPIO|Profile]. Profile Automation [System] pane pane Screen example [GPIO|Profile] GPIO Channel pane 3. Tap [New] in the Profile pane. The New GPIO Profile Setting screen is displayed. Screen example 5-48 (E) SRX-R515P...
  • Page 99 . An input profile can be selected for an input pin, and an output profile can be selected for an output pin. . When the Channel Profile has been changed, tap [Apply] after checking the content of Automation which uses the applicable channel in the Edit Automation dialog. 5-49 (E) SRX-R515P...
  • Page 100 The alphanumeric characters can be used as the Automation Name (up to 100 characters). An Automation command must be associated for each level when the type of a trigger is set to Level in GPIO Profile. In “State” on the New Automation screen, click the On or Off check box. 5-50 (E) SRX-R515P...
  • Page 101 0 to 7: Channels 0 (IN1) to 7 (IN8) 3. Save the changed contents and end the registration. (Refer to steps 6 to 8 in Section 5-13-1.) The GPIO channel registered as the playback start trigger of schedule playback cannot be associated with other operations. 5-51 (E) SRX-R515P...

  • Page 102: Other Settings

    Turns off the lamp. . Audio Muting: Reduces the sound. . System Shutdown: Shuts down the system. Only Stop Current Show and Lamp OFF can be selected when Projector Stop is selected in the Emer- gency Signal pane. 5-52 (E) SRX-R515P...
  • Page 103 The Emergency Response/Emergency Recovery signal is output only when the active state of the Fire Alarm signal is changed. Even if the Fire Alarm signal is inactive during startup, the signal that is set in Emergency Recovery is not output. 5-53 (E) SRX-R515P...

  • Page 104: Periodic Automatic Deletion Of File In External Folder

    The external folder to be treated is only a network-shared folder. To change a rule, specify the rule in the Rule List pane, change it, and then tap [Edit]. To delete a rule, specify the rule in the Rule List pane and tap [Delete]. 5-54 (E) SRX-R515P...

  • Page 105: Setting Of Shortcut

    [New] [Edit] [Apply] [Delete] Shortcut List pane [Shortcut|Assignment] Shortcut 3. Select No. (blank) in which no shortcut is registered in the Shortcut List, and then tap [New]. The New Shortcut Setting screen is displayed. Screen example [Apply] 5-55 (E) SRX-R515P...

  • Page 106: Log Output Setting

    This system can output a log once a day in the specified time. Log files are output as an individual file in units of one day. 1. Tap the “Configuration” tab. 2. Tap [Status] → [Logs]. The Logs screen is displayed. [Status] Configuration tab Screen example [Apply] Collect Logs daily at: pane [Browse] [Logs] [Filter] 5-56 (E) SRX-R515P...
  • Page 107 Screen example [OK] (2) Select the item you want to output, then tap [OK]. Place a mark in the “All Logs” check box when outputting a log containing all items. 7. Tap [Apply] after all settings are completed. 5-57 (E) SRX-R515P...

  • Page 108: Import And Export Of Setting Data

    The folder for exporting general settings must be registered in advance. (Refer to Section 5-12.) Connect a PC to the server when exporting the setting on a GUI screen. The exported setting data are saved in the folder set as the Firefox download folder of the PC. 5-58 (E) SRX-R515P...

  • Page 109: Audio Output Setting

    The audio channel output destination cannot be set during play- back. Procedure 1. Tap the “Configuration” tab. 2. Tap [System] → [AV|Setting]. The AV Setting screen is displayed. [System] Configuration tab Screen example [Apply] [AV|Setting] 5-59 (E) SRX-R515P...

  • Page 110: Creation Of Kdm Hot Folder

    3. Tap [Browse] in the KDM Hot Folder pane and select the external folder. A maximum of two external folders can be specified in a KDM hot folder. An external folder must be registered in advance. (Refer to Section 5-12.) 5-60 (E) SRX-R515P...

  • Page 111: Retrieving The Certificate

    The Certificate Information screen is displayed. [System] Configuration tab Screen example Download pane [Certificate|Info] 4. Select the certificate, you want to retrieve, in the pull-down menu of the Download pane and click [Download]. 5. Select the saving destination and click [OK]. 5-61 (E) SRX-R515P...

  • Page 112: Alignment Of The Screen Position Of Each Image (R, G And B)

    The Adjust Registration screen is displayed. (The screen example shows 2D screen.) [Projector|$2D%] Configuration tab Screen example Adjust Registration pane [Adjust|Registration] 3. Tap On in the Adjust Registration pane. 4. Adjust the screen position (horizontal and vertical) of each image (R, G and B) using [+][_] respec- tively. 5-62 (E) SRX-R515P...

  • Page 113: Turning Off The Lamps Individually

    [Projector|$2D%] Configuration tab Screen example [Adjust|Lamp] 3. Tap [OFF] of the lamp that you want to turn it off. If you want to turn on the lamp again, tap [ON] of the lamp that was turned off. 5-63 (E) SRX-R515P...

  • Page 114: Operating This System Using A Personal Computer (Pc)

    The login screen of this system is displayed. When an alarm screen is displayed The alarm screen below may display when connecting to a projection system for the first time or connect- ing to other projection systems. Screen example [Add|Exception...] button 5-64 (E) SRX-R515P...
  • Page 115 The lower part of the label is opened and a new message is displayed. 2. Click the [Add|Exception...] button. A dialog box for connection confirmation is displayed. 3. Click the [Confirm|Security|Exception] button. A GUI login screen is displayed. Screen example [Confirm|Security|Exception] button 5-65 (E) SRX-R515P...

  • Page 116: Changing The Setting Of Firefox

    5-15-2. Changing the Setting of Firefox 1. Enter about:config in the address bar and press the [Enter] key. Enter about:config. Screen example A configuration screen for gaining access to the setting screen is displayed. Screen example [I'll|be|careful,|I|promise|] button 5-66 (E) SRX-R515P...
  • Page 117 A Firefox setting screen is displayed. Screen example Double-click. 3. Double-click “browser.sessionstore.resume_from_crash” in the setting value list. You can refine the search by entering part of the name you want to search in the search column. Search field Screen example 5-67 (E) SRX-R515P...
  • Page 118 5. Double-click “browser.cache.disk.enable” in the setting value list. Screen example Double-click. 6. Check that the “true” changes to “false” in the Value and that the whole line changes to a bold face. 7. Double-click “browser.cache.memory.enable” in the setting value list. Screen example Double-click. 5-68 (E) SRX-R515P...
  • Page 119 12. Type 30 in the box, and then click the [OK] button. The dialog box is closed. Screen example [OK] button 13. Check that 30 is displayed in Value and that the whole line changes to a bold face. 14. Terminate Firefox. 5-69 (E) SRX-R515P...

  • Page 120: Shutdown

    Wait as it is. 3. When the MAIN indicator and LAMP indicator change to light in red and the IMB indicator changes to blink in red, turn off the power by setting the power switch to OFF (O). 5-70 (E) SRX-R515P...

  • Page 121: Installation Of Lens Change Table

    . Plate (foot): 1 pc Required tool . L-shaped scale (metal measure) Required grease . Sony grease SGL-601 (7-651-000-10) . Screwdriver . Hexagonal wrench: Subtense: 5 mm . Spanner: 19 mm (for flexible leveler nut) 30 mm (for leveler nut of projector) Tightening torque Tighten the following screws with the tightening torque described below.
  • Page 122 (8 x 25) Stay (320) (8 x 25) (Left side) (Right side) Apply grease to the two pins of the lens shift. Frame 2 20 mm Adjuster nut Foot Frame 2 (left side) Frame 2 (right side) 6-2 (E) SRX-R515P...
  • Page 123 B so that the projector and the plate (foot) become parallel to each other. Plate (foot) Hole Frame 2 Hole Hexagon PSW bolts (8 x 25) Convex portions Frame 2 Plate (foot) Frame 2 Frame 2 Adjuster nut Frame 2 Foot 6-3 (E) SRX-R515P...
  • Page 124 12. Adjust the other set of frame 1A, frame EX and frame 1B by repeating steps 10 and 11. Frame 1A Frame EX Hexagon Frame 1B PSW bolts (8 x 25) Adjust the height of frames so that it is slightly shorter than the distance between the frame 2 and ground. 6-4 (E) SRX-R515P...
  • Page 125 Frame 1A Hexagon PSW bolt Hexagon (8 x 25) PSW bolts (8 x 25) Frame EX Frame 1A Frame 1B Frame EX Stay (320) Frame 1B Hexagon PSW bolt (8 x 25) Nuts of flexible levelers (S) 6-5 (E) SRX-R515P...
  • Page 126 Installing the base plate assembly 17. Attach the base plate assembly with the four hexagon PSW bolts. Hexagon PSW bolts (8 x 25) Hexagon PSW bolts (8 x 25) Base plate assembly 6-6 (E) SRX-R515P...
  • Page 127 20. Tighten the fixing nuts of the flexible levelers (S) until it touches the top, and lock them. Projector panel Lens shift pins Base plate assembly Hexagon PSW bolts (8 x 25) Hexagon PSW bolts Hexagon (8 x 25) PSW bolts (8 x 25) Nuts of flexible levelers (S) 6-7 (E) SRX-R515P...
  • Page 128 22. Temporarily attach the stopper A and stopper B with the hexagon socket head cap bolt and washer respectively to the center portion. Base plate assembly Washers Hexagon socket head cap bolts (6 x 10) Stopper A Stopper B Stopper B Hexagon socket Stopper A Washers head cap bolts (6 x 10) 6-8 (E) SRX-R515P...

  • Page 129: Installation/Adjustment Of 2D Unit Assembly

    3. Remove the two screws (PSW4 x 10) from the 2D unit assembly. PSW4 x 10 2D unit assembly Grooves 2D unit assembly Stopper A Base plate assembly Washer Hexagon socket head cap bolt (6 x 10) 6-9 (E) SRX-R515P...
  • Page 130 2D unit assembly Clearance with the cap is about 1 to 2 mm. Lens base Stopper V Push the lens base to the lens as far as it will go. Lens front portion Stopper V Lens Lens base 6-10 (E) SRX-R515P...
  • Page 131 7. After the position of the stopper V is determined, pull out the lens base and securely tighten the two screws. 2D unit assembly PSW4 x 10 Stopper V Lens base 6-11 (E) SRX-R515P...

  • Page 132: Height Adjustment Of 2D Unit Assembly

    6-3-2. Height Adjustment of 2D Unit Assembly 1. Loosen the four hexagon PSW bolts on the both sides of the 2D unit assembly. Hexagon PSW bolts (8 x 25) 2D unit assembly Hexagon PSW bolts (8 x 25) 6-12 (E) SRX-R515P...
  • Page 133 . The lens base is raised when the hexagon socket head cap bolts are rotated in clockwise direction (2). 2D lens Hexagon socket head cap bolts (6 x 40) 2D unit assembly 2D lens Hexagon socket head cap bolts (6 x 40) Lens base Portion A Portion B 2D unit assembly 6-13 (E) SRX-R515P...

  • Page 134: Check After Adjustment

    6-3-3. Check after Adjustment 1. Check if the lens base can be moved back and forth smoothly. If not, perform “6-3-2. Height Adjustment of 2D Unit Assembly” again. Lens base 6-14 (E) SRX-R515P...
  • Page 135 Check that when the lock lever is moved in the direction of the arrow A, the two bosses are inserted into the hole under the lens and the lock is locked, and when the lock lever is moved in the direction of the arrow B, the lock is released. Lock lever Bosses Hole 6-15 (E) SRX-R515P...
  • Page 136 4. Securely tighten the four hexagon PSW bolts on both sides while pushing the 2D unit assembly downward. By pushing the 2D unit assembly downward, you can prevent the height from changing when secure- ly tightening the bolts. Hexagon PSW bolts (8 x 25) 2D unit assembly Hexagon PSW bolts (8 x 25) 6-16 (E) SRX-R515P...
  • Page 137 1) Adjust the projector panel and base plate assembly so that they are perpendicular (90°) to each other by referring to step 18 in Section 6-2. 2) Perform “6-3-2. Height Adjustment of 2D Unit Assembly”. Lens shift pins Holes 2D lens Handle 6-17 (E) SRX-R515P...

  • Page 138: Installation/Adjustment Of 3D Unit Assembly

    1. Insert the 3D unit assembly aligning with the grooves of the base plate assembly. 2. Attach the stopper B with the hexagon socket head cap bolt and washer. 2D unit assembly Grooves Base plate assembly 3D unit assembly Stopper B Washer Hexagon socket head cap bolt (6 x 10) 6-18 (E) SRX-R515P...

  • Page 139: Height Adjustment Of 3D Unit Assembly

    6-4-2. Height Adjustment of 3D Unit Assembly 1. Loosen the four hexagon PSW bolts on the both sides of the 3D unit assembly. Hexagon PSW bolts (8 x 25) 3D unit assembly Hexagon PSW bolts (8 x 25) 6-19 (E) SRX-R515P...
  • Page 140 . The lens base is raised when the hexagon socket head cap bolts are rotated in clockwise direction (2). 3D lens Hexagon socket head cap bolts (6 x 40) Lens base 3D unit assembly Hexagon socket head cap bolts 3D lens (6 x 40) Portion B Portion A 3D unit assembly 6-20 (E) SRX-R515P...

  • Page 141: Check After Adjustment

    3D lens. If the bosses cannot be smoothly inserted into and removed from the hole, perform “6-4-2. Height Adjustment of 3D Unit Assembly” again. Boss Lens base Lock lever Hole Lens base Lock lever 6-21 (E) SRX-R515P...
  • Page 142 3. Adjust the position so that the pin is inserted into the hole of stopper A, then secure the stopper A. Lens base View on arrow A Hole Hexagon socket Stopper A head cap bolt (6 x 10) 6-22 (E) SRX-R515P...
  • Page 143 4. Securely tighten the four hexagon PSW bolts while pushing the 3D unit assembly downward. By pushing the 3D unit assembly downward, you can prevent the height from changing when secure- ly tightening the bolts. 3D unit assembly Hexagon PSW bolts (8 x 25) 6-23 (E) SRX-R515P...
  • Page 144 1) Adjust the projector panel and base plate assembly so that they are perpendicular (90d) to each other by referring to step 18 in Section 6-2. 2) Perform “6-4-2. Height Adjustment of 3D Unit Assembly”. Lens shift pins Lock button Lens fixing lever Holes Handle 3D lens 6-24 (E) SRX-R515P...
  • Page 146 SRX-R515P (SY) . SRX-R515 . XCT-S10 . LKRA-007 LKRA-008 (WW) LKRL-A502 (SY) LKRL-A503 (SY) LKRL-Z511 (SY) LKRL-Z514 (SY) LKRL-Z519 (SY) LKRM-U330 (WW) Printed in Japan Sony Corporation LKRM-U450 (WW) J, E 2013. 2 32 9-968-995-01 ©2013...

Table of Contents