Sony FVS-1000 Series Operation Manual page 40

Specifications
HDTV functions (with an optional BKFV-100
installed)
System 1080/60I
1080/59.94I
1080/50I
1080/24P
1080/23.976P
Electrical zoom Area magnification: 0.5× to 4×
by Zoom or independent X and Y
sizing with pan and tilt affecting SD
(625/525) picture
Blanking control Independent X and Y adjusting
Image enhancer Horizontal and vertical aparture
correction with crispening, level
depend, horizontal and vertical peak
frequency, and detail gain control
Frame store for reference frame
4 frame @ HD 4:4:4
Wipe Horizontal and vertical wipe
Source selection: main, input, frame
store
Signal to noise ratio for luminance better than 58 dB
Video input HD SDI (4:2:2) or dual HD SDI
(4:4:4)
Video output HD SDI (4:2:2) or dual HD SDI
(4:4:4)
Monitor out (HD SDI 4:2:2 with a
superimposed signal)
Sequence output Pulldown sequence pulse
SDTV functions
The FVS-1000 system is furnished with one channel of SDI
processing board. A second channel can be configured by
adding the BKFV-200 SDTV processing board.
System 525/625 switchable
Electrical zoom Area magnification: 0.25× to 4×
by Zoom or independent X and Y
sizing with pan and tilt including
Crop, Squeeze and Letter box
...........................................................................................................................................................................................................
3) Measured at 50% video level, gamma = 0.4.
The ratio being 700 mV divided by r.m.s noise voltage
At the below conditions:
Film type: IP
Imager gain: M:2, R, G, and B; A000
Iris: 0000
Film Gamma: 7
Detail gain: 0000
Back level: Setting all 7FFF and after adjust
350 mV by Master level
4) It shows the status and film counter. As the pulldown
sequence is not considered, the film counter value in stop
mode is correct, but that in running mode may have an
error of 1 frame.
38
Blanking control
Image enhancer
Frame store
Wipe
Signal to noise ratio
Video input
Video output
Sequence output
Reference Input/Output (Analog)
3)
HD Input/Output
SD Input/Output
4)
Remote interface
RS-422
5) Measured at 50% video level, gamma = 0.4.
The ratio being 700 mV divided by r.m.s noise voltage
At the below conditions:
Independent X and Y adjusting
Horizontal and vertical aparture
correction with crispening, level
depend, horizontal and vertical
Master and detail gain control
for reference frame
16 frame @ SD 8:8:8
Horizontal and vertical wipe
Source selection: main, input, frame
store
for luminance better than 62 dB
D-1 SDI (4:2:2) - max. 3 channels or
dual D-1 SDI (4:2:2:4 or 4:4:4:4 or
8:4:4)
D-1 SDI (4:2:2), dual D-1 SDI
(4:4:4, 8:4:4) or D-1 SDI with a
superimposed signal
Monitor out (analog composite with
a superimposed signal)
Pulldown sequence pulse
Trilevel sync
field rate: 60/59.94
50/49.95
48/47.952
Black burst (NTSC/PAL)
525 sync
625 sync
Telecine controller I/F D-sub 9-pin
Film type: IP
Imager gain: M:2, R, G, and B; A000
Iris: 0000
Film Gamma: 7
Detail gain: 0000
Back level: Setting all 7FFF and after adjust
350 mV by Master level
5)
4)
.
4)