Example; Cable Entries - ABB ACS 601 Hardware Manual

Appendix A – ACS/ACC/ACP 601 Technical Data
ACx 601 Type
ACx 601-0040-6
ACx 601-0050-6
ACx 601-0060-6
ACx 601-0070-6
ACx 601-0100-6
ACx 601-0120-6
Note: Fuses from other manufacturers can be used if they meet the ratings given in the table. Only
ultra rapid fuses guarantee the proper protection for the rectifier semiconductors. The fuses
recommended in the table are UL recognized.

Example

Cable Entries

ACx 600 Type
ACx 601-0005-3/0006-5
ACx 601-0006-3/0009-5
ACx 601-0009-3/0011-5
ACx 601-0009-6/0011-6
ACx 601-0011-3/0016-5/0016-6
ACx 601-0016-3/0020-5/0020-6
ACx 601-0020-3/0025-5/0025-6
ACx 601-0025-3/0030-5/0030-6
ACx 601-0030-3/0040-5/0040-6
ACx 601-0040-3/0050-5/0050-6
ACx 601-0050-3/0060-5
ACx 601-0060-3/0070-5/0060-6
ACx 601-0070-3/0100-5/0070-6
ACx 601-0100-3/0120-5/0100-6
ACx 601-0120-3/0140-5/0120-6
1)The terminals are 10mm (13/32") bolts for attaching ring lugs (lugs not furnished).
2)IEC version. Range of cable diameters accepted by gland plate holes. For USA version conduit plate drawings, see pages B-9 and B-10.
A-6 ACx=ACS/ACC/ACP
2
A A s V Manufacturer
50 770 660 Bussmann
63 1450 660 Bussmann
100 4650 660 Bussmann
100 4650 660 Bussmann
125 8500 660 Bussmann
200 28000 660 Bussmann
For ACS 601-0120-3, the recommended fuses for the input bridge protection are 400 A
ultrarapid fuses.
The values I and I
for ACS 601-0120-3 are 175 A and 145 A respectively. 1.1 ·
1N 1hd
175 A = 192.5 A and 1.5 · 145 A = 217 A. Normal fuses with nominal currents higher
than 192.5 A or 217 A can be used to protect the input cable; thus, 200 A or 250 A
fuses are selected depending on the use (normal or heavy-duty, respectively).
Power and motor cable terminal sizes and tightening torques for the
ACS/ACC/ACP 601 with cable diameters accepted by the rubber
glands are given below. All power wiring must be rated for 60 °C
.
minimum
U1,V1,W1 / U2,V2,W2
Cable Ø
Maximum
mm
WIre Size
14...20
2
6mm
14...20
#10 AWG
14...20
14...20
2
10mm
14...20
#8 AWG
14...20
2 14...20
16mm
#6 AWG
14...20
2
Cu 35mm 20...26
#2 AWG
20...26
2
Al 50mm
20...26
#1 AWG
26...35
2
70mm
#00 AWG
26...35
1)
Fuses
Type
DIN 43620
170M1564
170M1565
170M1567
170M1567
170M1568
170M1570
Tightening
Torque
2)
1.5...1.8 Nm
13-18 lb.-in.
8Nm
5.9 lb.-ft.
30 Nm
22 lb.-ft.
Type
Size Size
DIN 43653
000 170M1364 000/80
000 170M1365 000/80
000 170M1367 000/80
000 170M1367 000/80
000 170M1368 000/80
000 170M1370 000/80
Ground (PE)
Cable Ø
Maximum
WIre Size
mm
10...14
2
6mm
10...14
#10 AWG
10...14
10...14
2
10mm
10...14
#8 AWG
10...14
2 10...14
16mm
#6 AWG
10...14
10...14
10...14
2
35mm
10...14
#2 AWG
10...14
10...14
2
70mm
#00 AWG
ACS/ACC/ACP 601 Drives