Table of Contents
Advertisement
1A-2 Engine General Information and Diagnosis:
• Be sure to read "Precautions for Electrical Circuit
Service in Section 00" before inspection and observe
what is written there.
• ECM replacement:
When substituting a known-good ECM, check for the
following conditions. Neglecting this check may cause
damage to a known-good ECM.
– Resistance value of all relays, actuators is as
specified respectively.
– MAP sensor, A/C refrigerant pressure sensor and
TP sensor are in good condition and none of power
circuits of these sensors is shorted to ground.
• Communication of ECM, BCM, ABS/ESP® control
module, combination meter, keyless start control
module, steering angle sensor (ESP® model) and
TCM (A/T model), is established by CAN (Controller
Area Network). (For more detail of CAN
communication for ECM, refer to "CAN
Communication System Description"). Therefore,
handle CAN communication line with care referring to
"Precaution for CAN Communication System in
Section 00".
• Immobilizer transponder code registration after
replacing ECM
When ECM is replaced with new one or with another
one, make sure to register immobilizer transponder
code to ECM correctly according to "Procedure after
ECM Replacement in Section 10C".
Statement on Cleanliness and Care
An automobile engine is a combination of many
machined, honed, polished and lapped surfaces with
tolerances that are measured in the thousands of an
millimeter (ten thousands of an inch).
Accordingly, when any internal engine parts are
serviced, care and cleanliness are important.
It should be understood that proper cleaning and
protection of machined surfaces and friction areas is part
of the repair procedure. This is considered standard
shop practice even if not specifically stated.
• A liberal coating of engine oil should be applied to
friction areas during assembly to protect and lubricate
the surfaces on initial operation.
Precautions of ECM Circuit Inspection
• ECM connectors are waterproofed. Each terminal of
the ECM connectors is sealed up with the grommet.
Therefore, when measuring circuit voltage, resistance
and/or pulse signal at ECM connector, do not insert
the tester's probe into the sealed terminal at the
harness side. When measuring circuit voltage,
resistance and/or pulse signal at ECM connector,
connect the special tool to the ECM connectors. And,
insert the tester's probe into the special tool's
connectors at the harness side, and then measure
voltage, resistance and/or pulse signal. Or, ECM and
its circuits may be damaged by water.
• Wire colors of the special tool's connectors are
different from the ones of the ECM connectors.
However, the circuit arrangement of the special tool's
connectors is same as the one of the ECM
connectors. Therefore, measure circuit voltage and
resistance by identifying the terminal location subject
to the measurement.
Precautions of Electric Throttle Body System
Calibration
After performing one of works described below, it is
necessary to re-register the completely closed throttle
valve reference position stored in memory of ECM. (For
detailed information, refer to "Description of Electric
Throttle Body System Calibration".) For the procedure to
register such data in ECM, refer to "Electric Throttle
Body System Calibration in Section 1C".
• To shut off backup power of ECM for such purposes of
battery replacement or "DOME" fuse removal
• To erase DTCs P0122, P0123, P0222, P0223, P2101,
P2102, P2103, P2111, P2112, P2113, P2119, P2123,
P2127, P2128, P2135 and/or P2138
• To replace ECM
• To replace throttle body and/or accelerator pedal
position (APP) sensor assembly
General Description
• Whenever valve train components, pistons, piston
S7RS0B1101001
rings, connecting rods, rod bearings, and crankshaft
journal bearings are removed for service, they should
be retained in order.
At the time of installation, they should be installed in
the same locations and with the same mating
surfaces as when removed.
• Battery cables should be disconnected before any
major work is performed on the engine.
Failure to disconnect cables may result in damage to
wire harness or other electrical parts.
S7RS0B1100003
S7RS0B1100004
Hide quick links:
Advertisement
Chapters
Table of Contents
