Panasonic AW-HE130KP Operating Instructions Manual page 92

Web screen configurations (continued)
Advanced network setting screen [Advanced]
„
Click the [Advanced] tab in the network setup screen [Network].
Settings relating to the NTP, UPnP, HTTPS, SNMP, and Diffserv
functions are performed here.
Click the links to each item to move to the respective setting page.
z NTP
Settings relating to the NTP server address and port No. are
performed here.
NTP server address setting
Select the method to acquire the NTP server address.
Setting value:
Auto Acquires the NTP server address from the DHCP server.
Sets the address by inputting the NTP server address in
Manual
[NTP server address].
Factory settings: Manual
<NOTE>
• To acquire the NTP server address from the DHCP server, [Network
Settings] (→ page 89) must be set to either [DHCP], [Auto(AutoIP)] or
[Auto(Advanced)] in the [Network] tab of the network setup screen
[Network].
NTP server address
When [Manual] is selected in the [NTP server address setting], input
the IP address or host name of the NTP server.
Maximum number
1 to 128 half-size characters
of characters
Characters that Half-size alphanumeric characters, half-size symbols
can be entered :. _ -
Factory settings: blank
<NOTE>
• To input the [NTP server address] host name, the [DNS] setting
must be selected on the [Network] tab of the network setup screen
[Network] (→ page 89).
NTP port
Input the port No. of the NTP server.
Port Nos. that can be selected: 1 to 65535
The following port numbers are used by the unit so they cannot be
used.
20, 21, 23, 25, 42, 53, 67, 68, 69, 80, 110, 161, 162, 443, 995, 10669,
10670
Factory settings: 123
92
Time adjustment interval
Selects the interval (1 to 24 hours in 1-hour increments) for acquiring
the time from the NTP server.
Setting range: 1h to 24h
Factory settings: 1h
Time zone
Selects the time zone according to the region where the camera is
being used.
Factory settings:
(GMT)Greenwich Mean Time: Dubin, Edinburgh, Lisbon, London
Summer time(daylight saving)
Sets whether to use summer time.
Selects the time zone that corresponds with the region in which the
unit is going to be used.
Setting value:
In Sets the time to summer time.
Out Cancels summer time.
Switches to summer time according to the start/end time
Auto
and date settings (time, day, week, month).
Factory settings: Out
Start time & date
End time & date
Sets the summer time start/end time and date by time, day, week and
month when [Auto] is selected in the [Summer time(daylight saving)]
setting.
z UPnP
This unit supports UPnP (Universal Plug and Play). Using the UPnP
function allows the following to be set automatically.
• Sets the router's port forwarding function. (However, a UPnP-
compatible router is necessary).
This setting is useful when accessing the camera from the Internet
or a portable terminal.
• It is set so that a short cut to the camera is created in the "Network"
folder of your personal computer and that short cut is automatically
renewed even when the camera's IP address is changed.
Auto port forwarding
Whether to use the router's port forwarding function is set by selecting
"On" or "Off".
To use the automatic port forwarding function, the used router must
support UPnP and the UPnP function must be enabled.
Setting value:
On Uses the router's port forwarding function.
Off The router's port forwarding function is not used.
Factory settings: Off
<NOTE>
• The port number may be changed by automatic port forwarding. If
the number is changed, the port No. of the camera registered to the
personal computer or recorder must be changed.
• The UPnP function may be used when the camera is connected to
the IPv4 network. IPv6 is not supported.
• To confirm that automatic port forwarding is correctly set, click the
[Status] tab in the maintenance screen [Maintenance] to confirm that
the [UPnP] status is set to [Enable]. (→ page 101)
If [Enable] is not displayed, refer to "Cannot access the Internet from
the Camera" in the "Troubleshooting" section. (→ page 113)