Panasonic AW-HE130KP Operating Instructions Manual page 85

Web screen configurations (continued)
Speed With Zoom POS.
"Off" or "On" is set here for the function used to adjust the pan-tilt
adjustment speed in conjunction with the zoom magnification.
When [On] is set, the panning and tilting operations will become
slower in the zoom status.
This function has no effect during preset operations.
Setting value: Off /On
Factory settings: On
Focus Mode
Select auto or manual mode for the focus adjustment function.
Setting value:
Auto Always adjust focus automatically.
Manual Adjust focus manually.
Factory settings: Auto
<NOTE>
• [Focus Mode] cannot be set to [Auto] when [Frame Mix] is set to
[18dB] or [24dB].
Focus ADJ With PTZ.
"Off" or "On" is set here for the function which compensates for out-of-
focusing when it occurs during panning, tilting or zooming operations.
When [Off] is set, adjust the focus as required after zooming or set
the focus to the auto mode.
This item can be selected only when [Manual] has been selected as
the [Focus Mode] setting.
Setting value:
Off Out-of-focusing is not compensated.
On Out-of-focusing is compensated.
Factory settings: Off
Digital Zoom
"Enable" or "Disable" is set here for the digital zoom function.
If zooming is performed toward the Tele end beyond the maximum
position when [Enable] has been selected, the digital zoom can be
operated continuously. Zooming will stop temporarily at the position
where the optical zoom and digital zoom are switched so after it has
stopped at this position, proceed with zooming again.
When the setting is changed to "Disable" while already in the digital
zoom region, the zoom will automatically move to the maximum
position of the optical zoom.
Setting value: Disable / Enable
Factory settings: Disable
The digital zoom is set to off when color bars are displayed during
digital zooming.
Max Digital Zoom
Set the maximum digital zoom magnification.
Setting value:
x2 / x3 / x4 / x5 / x6 / x7 / x8 / x9 / x10
Digital Extender
Turn the digital extender function off/on.
When this is set to [On], the digital zoom will be fixed at 1.4x.
When [Digital Zoom] is set to [Enable], [Digital Extender] is disabled.
Setting value: Off /On
Factory settings: Off
OIS
Enable or disable the optical image stabilization (OIS) function.
Setting value: Off/On
Factory settings: Off
<NOTE>
• The optical image stabilization (OIS) function's level of correction is
reduced during pan/tilt operations.
Tally
"Enable" or "Disable" is set here for the function which turns on or
turns off the tally lamp using the tally control signal.
Setting value: Disable / Enable
Factory settings: Enable
Tally Brightness
Adjust the brightness of the tally LED.
Setting value: Low / Mid / High
Factory settings: Low
<NOTE>
• When this is set to [Low], the LED brightness is equivalent to that of
the AW-HE120.
OSD Mix
Select whether to turn off/on camera menu, status, and other displays
for each output image.
Setting value: Off / On
Factory settings: On
SDI Out
HDMI Out
Video Out
IP
When this is set to [On], the camera menu, status, and other displays
for corresponding output image are displayed.
Setting value:
The camera menus and statuses are not displayed on the
Off
output pictures targeted by the setting items listed above.
The camera menus and statuses are displayed for the output
On
pictures covered by the setting items listed above.
Factory settings: On
<NOTE>
• When this is set to [Off], the camera menu can be displayed for
about 1 minute after the unit is turned on.
OSD Off With Tally
On or off the function that turns off camera menu, status, and other
displays when tally signals are received via commands or contacts.
When the tally signal releases, the camera menu display will return.
Setting value: Off / On
Factory settings: Off
OSD Status
Turn the status display during AWB and ABB on/off.
Setting value: Off / On
Factory settings: Off
Model Select
Set the protocol model for standard serial communication.
Do not select [Reserved1] to [Reserved7].
Appears when the service switch (SW4) at the bottom of the unit is
set to ON (standard serial communication).
Setting value:
SEVIHD1 / SBRC300 / SBRCZ330 / Reserved1 to 7
Factory settings: SEVIHD1
85