Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HAKO Hakomatic E 430
Summary of Contents for HAKO Hakomatic E 430
- Page 1 Instruction Manual Hakomatic E 430 (7324.12)
- Page 2 Introduction It is our desire that the excellent pro- perties of the Hakomatic E 430 should Please be advised explicitly that justify the confidence you demonstra- we cannot accept any legal ted by making this purchase. claims out of the contents of this We did our best to supply you with an manual.
-
Page 3: Introduction
Modifications made to the pert handling and unauthorized Hakomatic E 430 in absence of the modification of the machine. manufacturer's consent will relieve the Moreover, any claim for warranty beco-... -
Page 4: Table Of Contents
4.3.3 Replacement of sealing strips General safty instraction Water infeed Principle of operation 4.5 Operating procedure Description Hakomatic E 430 4.5.1 Soiled and fresh water tanks 3.1 Controls element 4.6 Electrical equipement 3.1.1 Switch for suction motor and brushes Technical data 19/20 3.2 Cleaning solution discharge... -
Page 5: General Safety Instructions
The warning and instruction plates at- the unit or his authorized representati- During driving operation, he has to tached to the Hakomatic E 430 give ve and who have been ordered expli- take account of the local conditions important advice about safe operation. - Page 6 Remove water if requi- The machine may be used only on The Hakomatic E 430 has to be che- red. hard floorings and for operation on cked for its proper and safe operation...
- Page 7 1. General safety instructions Handling of line cords Make sure that the line cords are not damaged by running over, squeezing, dragging , etc. The line cords shall be Caution! checked regularly with regard to Any work at the electrical system, e.g. damage and ageing.
-
Page 8: Principle Of Operation
During the practice then soon will make you find first cycle, the floor is scrubbed with the ideal Hako detergent and the per- the cleaning agent selected according fect dosage applicable to it. to the degree of dirt encountered, the... -
Page 9: Description
3. Description 3.1 Control panel 3.1.1 Switch for suction motor and B Suction turbine speed selector brush High suction power When the floor is rough B shall be at this position Low suction power Fig.3 When the floor is smooth B shall be at this position on/off for suction turbine is on when “A”... -
Page 10: Cleaning Solution Discharge
3. Beschreibung D Switch for brush release 3.2 Cleaning solution discharge 3.3 Pedal for lifting the brush Lever Fig.5 Fig.4 Fig.6 1 Pedal for lifting brush Control 2 Speed control lever brush will be released when D is Turn the lever up , to discharge at position “... -
Page 11: Control For The Speed Of Machine Mouvment (Powerflow)
3. Description 3.4 Control for the speed of 3.5 Raising / lowering the squeegee machine movement (Powerflow) Pull the black knob a little. Take the knob to the left to increa- se the speed. Take it to the right to decrease speed. -
Page 12: Draining Of Soiled Water Tank
3. Description 3.6 Draining of Soiled water tank 3.7 Draining of Fresh water tank Is used to drain the soiled water. Is used to drain the fresh water. Note : when work is completed, the Note : The tank requires rinsing at soiled water tank to be drained and regular intervals rinsed... -
Page 13: Taking Into Operation
4. Taking into operation 4.1 Machine to the 1 Tilt the body of the machine after re- 2 The brush motor is fastened to its moving rubber caps & allen guide ways by a screw in order to employment prepare screws(on both sides) in order to prevent unwanted movement during Gain access to the inside of the ma-... - Page 14 4. Taking into operation 3 Close the body back and secure it 4 Take the machine out of the pallette with screws and Rubber caps. Re- carefully. Fit the drain hoses move the two tie-bolts outside the (2 Nos.) ensuring the position of body of the Machine .
-
Page 15: Brushes/Pads
4. Taking into operation 4.2 Brushes and pads 4.2.2 Removal of brush Empty the tanks. The Hakomatic E 430 must be Lift the squeegee and the brush. equipped with brushes from the Machine switch on accessories kit, as required by the Turn on switch "D"... -
Page 16: Squeegee
4. Taking into operation 4.3 Squeegee 4.3.2 Removal of squeegee The Hakomatic E 430 is equipped with Lift the squeegee. a squeegee with a working width of Unscrew the stra-shaped knob(2) 750 mm . The squeegee bracket Remove the squeegee towards the... -
Page 17: Water Infeed
Germany). side (sealing strips with slots to Open the tank lid and tilt it to the When the Hakomatic E 430 is being frontside, and plain one to the rear) Rear. pushed, squeegee and brush drive Fill the fresh water tank with water plate must be lifted. -
Page 18: Operating Procedure
Note: After lowering the brush move Partially occupied areas should be the Hakomatic E 430 immediately; subdivided into single working areas, Otherwise the brush might leave tra- within reach of the power Supply ca- ces on the floor. -
Page 19: Soiled And Fresh Water Tanks
4. Taking into operation 4.5.1 Soiled and fresh water tanks The Hakomatic E 430 has soiled When work is finished: water tank and a fresh water (lye) tank. The filling capacity is 22 litres; Stop the machine and lift the brush .Please do not fill beyond that mark;... -
Page 20: Electrical Equipement
4. Inbetriebnahme 4.6 Electrical equipment The electrical equipment of the Hako- The protector can be reset by pressing matic E 430 uses a mains voltage of the transparent dome on the electrical 230V/50 Hz AC. box cover. Please allow approximately Easy access to brush motor and 30 seconds time before resetting. -
Page 21: Technical Data
5. Technical data Dimensions Length with squeegee 450/750 Width without/with squeegee 807/870 Height at handlebar, from ...to Working width Brush head Squeegee Surface performance, Theoretical m 2 /h 1700 Driving speed km/h Up to Weights Deadweight, dry Total weight, ready to operate, wet Tyre 75/28 Front wheel, dia./width... - Page 22 5. Technical data Brush head Number of brushes Brush dia 1/min Brush speed Brush contact pressure, max.up to N/cm 2 0,25-0,35 Specific ground pressure Vacuum suction m 3 /h Air throughput mm/WS 2000 Vacuum pressure Electrical equipment AC Volt Service voltage EN 60335-2-72 Protection class EN 60335-2-72...
-
Page 23: Brushes
6. Brushes Brush Plastic PPN 0,5 7433 7. Pads Poly-Pad 41 cm braun 7087 Super -Pad brown (also necessary : 7437 drive plate 7436 ) Drive plate ( pad holder ) with center -lock 7436 8. Additional tools for working with suction hose Flexible synthetic hose ,300 cm 7880 Suction tube , 130 cm ,... -
Page 24: Maintenance And Service
The nameplate is fixed suitable tools and by the people trai- in the rear side of the machine. ned in the factory. For reasons of safe- ty, only genuine Hako spare parts may be used. - Page 25 9. Maintenance and service Betriebsstunden 9.2 Maintenance table Daily every 50 every 100 every 200 Check connection -extension cables and plugs for good condition; discard defective cables immediately. Empty and clean (rinse) the soiled water tank Check the sealing strips of squeegee for good condition. Check the squeegee for possibly collected foreign matter and clean it, if required Check the float for proper operation...
- Page 26 9. Maintenance and service Betriebsstunden 9.2 Maintenance table Daily every 50 every100 every 200 Check the tank lid seal; renew it if required. Check the fresh water infeed to the brushes. Remove carbon dust from the suction motor ,Check the carbon brushes for easy Operation and wear, renew the carbon brushes as required.
-
Page 27: Eg-Declaration Of Germany
The machine may be used only for must be agreed on with your authorized operation on plane areas with a maxi- Hako dealer in accordance with the Bat- mum inclination of up to 2 %. tery Law § 6 and § 8 (BattG) - Page 28 Ludger Lüttel declares that the products EN 60335-2-72 Hakomatic B 430, Typ 7336.02 EN 55012 Hakomatic E 430, Typ 7324.12 EN 61000-6-2 to which this declaration relates, con- Bad Oldesloe, 27.10.2010 form to the relevant provisions of the safety and health requirements stipulat- ed in EC Directive 2006/42/EC and is in accordance with 2004/108/EC.
- Page 30 Spitzentechnik für eine saubere und schönere Umwelt Superior technology for a cleaner and better environment Hako GmbH · Hamburger Str. 209-239 · D-23843 Bad Oldesloe · (0 45 31) 806-0 · Fax (0 45 31) 806-338...
Need help?
Do you have a question about the Hakomatic E 430 and is the answer not in the manual?
Questions and answers