HAKO Hakomatic B45 Instruction Manual
  1. Manuals
  2. Brands
  3. HAKO Manuals
  4. Scrubber
  5. Hakomatic B45
  6. Instruction manual

HAKO Hakomatic B45 Instruction Manual

Hide thumbs Also See for Hakomatic B45:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
Instruction Manual
Hakomatic B45 (7700)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hakomatic B45 and is the answer not in the manual?

Questions and answers

Related Manuals for HAKO Hakomatic B45

Summary of Contents for HAKO Hakomatic B45

  • Page 1 Instruction Manual Hakomatic B45 (7700)

  • Page 2: Introduction

    Therefore, this operation and main- manufacturer's specifications. Hako-Werke GmbH tenance manual must be read and The Hakomatic B45 may only be used understood prior to the machine being D-23843 Bad Oldesloe by persons that are familiar with the ma- used for the first time.

  • Page 3: Notes On Warranty

    AG or your freight forwarder confirm The maintenance work has to be perfor- such damage. Mail notification and med by an authorized Hako service waybill to: center and confirmed in the "Mainte- nance certificate" which is the warranty Hako-Werke GmbH document.

  • Page 4: Table Of Contents

    Squeegee....41 Initial charging procedure . . . 10 Hako System Maintenance . 27 5.8.1 Cleaning the squeegee ..41 Before Putting into Operation 10 Maintenance Document .

  • Page 5: Safety Information

    Safety information Safety information Safety and Warning Symbols All paragraphs in this manual referring to your personal safety, the safety of your machine and the environment pro- tection are attributed one of the follo- wing warning symbols: Symbol Hazardous for ... Description Safety Provisions persons and goods...

  • Page 6: General Provisions

    (non-foaming) and obser- Hako assumes no liability for dama- rors during operation of the machine ve all the use, disposal and warning ge to the battery caused by a fault...

  • Page 7: Maintenance Information

    Safety information machine, remove the key from the repairs . the safety equipment has been in- main switch (Hakomatic B45 CL/ • Spare parts must comply with the mi- stalled and brought to its protecting CLH only). nimum technical requirements stipu- position.

  • Page 8: Information For Protection Of Environment

    According to the crossed dustbin la- bel these batteries must not be ad- ded to the normal waste. Provide for agreement with the Hako contract dealer on return and disposal accor- ding to § 8 BattV.

  • Page 9: Labels On The Machine

    A = Read and observe the operating manual (Fig. 1/4) B = Maximum permissible gradient 2% (Fig. 1/4) C = Do not clean the machine with a Rating plate (Fig. 1/2a) pressure washer (Fig. 1/4) Explosive gases (Fig. 1/2b) Fig.1 Hakomatic B45...

  • Page 10: First Operation

    First Operation First Operation Before Putting into Operation Switching the machine on Complete the following inspections be- Before switching the machine Instruction fore taking the machine into operation: on, please read the safety in- Instruction is required before first ope- 1.

  • Page 11: Operation

    First Operation • Switch the machine on by actuating Operation Hakomatic B45 CL/CLH the switch (Fig. 3/1) from position (0) 1. Switch the machine on using the key Hakomatic B45 to position (1). switch. All the units are in Standby 1.

  • Page 12: Useful Tips

    The floor should be treated twice in the the right Hako cleaning agent and the case of particularly dirty floors or to re- optimum dosage to suit your needs.

  • Page 13: Stopping And Switching Off The Machine

    (on both si- switch. 5. Check the sealing strips and suction des) and rear at the eye bolts (Fig. 4/1). Hakomatic B45 CL/CLH hose. 1. Release the safety switch: 6. Check the electrical equipment, - The traction drive, brush drive and functions and settings.

  • Page 14: Operation

    Operation Operation Method of operation General information The Hakomatic B45 is a scrubber dryer for the wet cleaning of hard floors. 3.1.1 Brush head The brush in the brush head (Fig. 5/1) is driven by an electric motor. The brush head is lowered by means of the brush pedal.

  • Page 15: Squeegee

    3.1.5 Power flow / traction drive The hand-guided Hakomatic B45 is op- timally supported by the power flow of the brush drive. The Hakomatic B45 CL/CLH is provided with a continuously adjustable traction drive.

  • Page 16: Batteries And Charger

    (7036.40) • Mop holder and tool net for cleaning tools (7725) • Dosing system (7056.02) • Float unit (7715) Hakomatic B45 CL/CLH only: • Tool connector (7724) • Floor scrubbing unit (7009) Hakomatic B45 CL only: • Silence kit (7730)

  • Page 17: Operating And Indicator Elements

    Operation Operating and indicator elements 3.2.1 Operating panel Hakomatic B45 1 Indicator field for: - Operating hour counter - Service indicator and - TSG indicator 2 Charge control indicator 3 Main switch 4 Dead-man's switch 5 Brush ejector Fig.8 Hakomatic B45...
  • Page 18 Clear the fault or note down the service The number of LEDs lit up corresponds code and inform your authorized Hako to the following charge status: dealer. 2 LEDs light up = charging has started...

  • Page 19: Hakomatic B45

    Operation Hakomatic B45 CL/CLH 1 Indicator field for: - Operating hour counter - Service indicator and - TSG indicator 2 Charge control indicator 3 Main switch 4 Dead-man's switch 5 Direction switch 6 Driving speed control 7 Symbol for silence kit (option)
  • Page 20 Clear the fault or note down the service 2 LEDs light up = charging has started code and inform your authorized Hako 3 LEDs light up = 75% charge dealer. 4 LEDs light up = 100% charge...

  • Page 21: Dead-Man's Switch

    Operation Dead-man's switch (Fig. 9/4) If the dead-man's switch on the bail sy- stem is released during operation, the Symbol for silence kit (option) Tool connection button (option) traction drive, brush head drive and so- lution supply are switched off. The suc- (Fig.
  • Page 22 Operation dead-man's switch of the bail system, the brush is automatically attached. Solution dosage button (Fig. 9/7) Brush ejection button (Fig. 9/13) The solution quantity can be adjusted The brush can be removed for mainte- during operation. The level selected ap- nance purposes by pressing a button.

  • Page 23: Machine

    1 Solution tank filling neck 2 Squeegee lift lever 3 Solution filter 4 Solution draining hose 5 Charger power connection 6 Brush head lift foot pedal 7 Waste water draining hose 8 Solution dosage hand valve Hakomatic B45 only Fig.10 Hakomatic B45...
  • Page 24 Solution draining hose (Fig. 10/4) Solution hand valve (Fig. 10/8) The solution tank draining hose is used In the case of the Hakomatic B45, the to drain the solution. solution to the brush head is set by means of a hand valve. The solution quantity can be regulated between 0 l/ min and 1.85 l/min.

  • Page 25: Technical Data

    Working width (17“/20“) 43/51 Squeegee width (17“/20“) 76/86 Area coverage, theoretical (17“/20“) m²/h 1720/2040 Nominal voltage Power consumption, traction drive (Hakomatic B45 CL/CLH only) Power consumption, aspirating engine Power consumption, brush motor No. of brushes Pieces Brush diameter (17“/20“) 43/51 Working speed...
  • Page 26 Technical Data Without With Noise emission value silence kit silence kit Sound power level (LwA) measured according to DIN EN 60335-2-72 under maximum working conditions: dB (A) The sound pressure level (LpA) (at the ear of the operator) measured according to DIN IEC 60335-2-72 under normal working conditions: dB (A) Measurement inaccuracy (KpA):...

  • Page 27: Maintenance And Care

    Please contact your lo- instructions (daily or weekly). The dri- cal Hako Service Centre or Hako con- ver/operator will be instructed upon de- tract dealer. We cannot be held liable livery of the machine.

  • Page 28: Maintenance Document

    Maintenance and Care Maintenance Document Handing over Hako-System-Maintenance I Hako-System-Maintenance II Hako-System-Maintenance I 125 operating hours 250 operating hours 375 operating hours Upgrade Workshop stamp Workshop stamp Workshop stamp Test drive Handing over to the customer Instruction carried out on:...

  • Page 29: Maintenance Schedule

    Maintenance and Care Maintenance Schedule Hako-System Maintenance Custo- The daily and weekly maintenance works are to be performed by the custo- mer/operator. Interval To be performed daily weekly Fill clear water tank and proceed to chemical agent dosage Charge batteries...
  • Page 30 Maintenance and Care Hako-System Maintenance I The following maintenance works are to be performed by an authorised Hako Service workshop. Interval To be performed every 125 hours of operation Check battery charger Check tank lid sealing of the soiled water tank and replace if required...
  • Page 31 Service workshop. Interval To be performed every 250 hours of operation Perform maintenance works according to Hako-System Maintenance I Inspect steering rollers for tread damages and bearing slackness and replace if required Check function of water pump and replace if required...
  • Page 32 1000 operating hours) Check brake of the travel drive motor (Hakomatic B45 CL/CLH only) Clean travel drive motor (Hakomatic B45 CL/CLH only) from carbon dust and check carbon brushes for smooth operation and wearing and replace carbon brushes if required...

  • Page 33: Battery System

    The machine functions are re- stricted. Charge the batteries immediately! If the grounded plug is not in- serted in the holder (Fig. 11/5) after the charging process, the integrated machine immobili- zer prevents the machine being started up! Fig.11 Hakomatic B45...

  • Page 34: Charging Batteries

    Return and recycling must be agreed (Fig. 11/8). Ensure sufficient ventilation in on with Hako's authorized dealer in ac- 4. Disconnect the battery terminal the charging area when char- cordance with § 8 BattV (Battery Direc- (Fig. 11/6).

  • Page 35: Solution Tank

    Maintenance and Care Solution tank 1 Solution tank 2 Marking 3 Fill level hose 4 Solution filter 5 Tank cap Fig.12 Hakomatic B45...

  • Page 36: Filling The Solution Tank

    Maintenance and Care 5.5.1 Filling the solution tank 5.5.3 Cleaning the fresh water filter Fill the solution tank (Fig. 12/1) before Check the solution filter (Fig. 12/4) wee- starting work or as necessary. Park the kly and clean or replace it as necessary. vehicle on a level floor area.

  • Page 37: Soiled Water Tank

    Maintenance and Care Soiled Water tank 1 Soiled Water Tank 2 Drain hose 3 Suction filter 4 Tank lid 5 Drain valve sealing 6 Tank lid sealing Fig.13 Hakomatic B45...

  • Page 38: Empty Soiled Water Tank

    Maintenance and Care 5.6.1 Empty Soiled Water Tank 5.6.2 Clean Soiled Water Tank 5.6.4 Checking the Draining valve Clean soiled water tank (Fig. 13/1) at Clean soiled water tank (Fig. 13/1) at seal daily intervals, as required or upon daily intervals or as required. Check the functionality of the draining acoustic signal (increased suction turbi- 1.

  • Page 39: Brush Head

    Maintenance and Care Brush head 1 Brush 2 Brush head 3 Brush head lift lever 4 Brush ejection button 5 Deflector roller 6 Sealing strip Fig.14 Hakomatic B45...

  • Page 40: Changing The Brushes

    Maintenance and Care 5.7.1 Changing the brushes the brush head. When the brush head Check the brushes (Fig. 14/1) in the drive is switched on by means of the brush head (Fig. 14/2) weekly for signs dead-man's switch of the bail system, of wear.

  • Page 41: Squeegee

    Maintenance and Care Squeegee 5.8.1 Cleaning the squeegee 5.8.2 Changing the sealing strips Check the squeegee (Fig. 15/1) daily Check the inner and outer sealing strips 1 Squeegee and clean it as necessary. on the squeegee (Fig. 15/1) weekly for 2 Star-shaped knob To clean the squeegee raise it, discon- signs of wear.

  • Page 42: Adjusting The Sealing Strips

    Maintenance and Care 5.8.3 Adjusting the sealing strips Angle adjustment The angle adjustment is decisive in controlling whether the squeegee's sealing strips lie evenly on the floor. 1. Park the machine on a level surface and lower the squeegee. 2. Loosen the counternut on the adju- sting bolt (Fig.
  • Page 43 Maintenance and Care Height adjustment The height adjustment is set to 3 mm at the factory. If streaks appear despite an optimum angle adjustment, the di- stance of the rollers to the floor must be adjusted by changing the number of washers on the holder.
  • Page 44 Maintenance and Care Circular brush head Cleaning the brushes Changing the brushes Clean the brushes in the brush head Check the brushes (Fig. 14/4) in the 1 Brush head lift lever (Fig. 14/2) daily or as necessary. brush head weekly for signs of wear. In 2 Brush head 1.

  • Page 45: Rotary Brush Head

    Maintenance and Care 5.10 Rotary brush head 1 Slotted-head screw 2 Cover 3 Waste container 4 Deflector roller 5 Catch 6 Brushes 7 Sealing strips 8 Spray jets 9 Knurled screws Fig.19...
  • Page 46 Maintenance and Care 5.10.1 Cleaning the brush head the cover again with the slotted-head Only use original spare parts! Check the brush head daily and clean it screw. Only use original spare parts! 5.10.5 Checking the spray jets as necessary. Check the spray jets daily and clean When installing the brushes, 1.
  • Page 47 The machine may be used only for must be agreed on with your authorized operation on plane areas with a maxi- Hako dealer in accordance with the Bat- mum inclination of up to 2 %. tery Law § 6 and § 8 (BattG)

  • Page 48: Ec-Declaration Of Conformity

    EC Declaration of Conformity (corresponds to EC Directive 2006/42/EC) Hako-Werke GmbH Reference was made to the following Name of the authorized person who standards and/or norms and/or techni- compiles technical documents for Hamburger Straße 209-239 cal specifications to ensure proper im-...
  • Page 50 Spitzentechnik für eine saubere und schönere Umwelt Superior technology for a cleaner and better environment Hako-Werke GmbH · Stammwerk und Hauptverwaltung · Headquarter Hamburger Str. 209-239 · D-23843 Bad Oldesloe · (0 45 31) 806-0 · Fax (0 45 31) 806-338...

This manual is also suitable for:

7700

Table of Contents

Save PDF