Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for 909 BN210
Summary of Contents for 909 BN210
- Page 1 INSTRUCTION MANUAL BN210 1400W 210mm ( 8 1/4" ) COMP OUND MI T RE SAW...
-
Page 2: Table Of Contents
CONTENTS Warranty Warranty Power Tools Introduction For full details please visit us at www.909.com Environmental protection Description of symbols Specifications General safety rules Additional safety rules for mitre saws Accessories Know your product Unpacking Transportation Bench mounting Release knob Mitre table locks... -
Page 3: Introduction
Cautions and Warnings. Conforms to relevant safety standards. Your 909 power tool has many features that will make your job faster and easier. Safety, performance, and For safe operation read instruction manual. dependability have been given top priority in the development of this tool, making it easy to maintain and operate. -
Page 4: General Safety Rules
General safety rules f) To reduce the risk of electric shock, the manufacturer recommends the use of a residual current device WARNING. Read all safety warnings and all instructions. with a rated residual current of 30mA or less at Failure to follow the warnings and instructions may result in all times. -
Page 5: Additional Safety Rules For Mitre Saws
4) Power tool use and care i) Children should be supervised to ensure that they do not play with the appliance. a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will 5) Service do the job better and safer at the rate for which it was a) Have your power tool serviced by a qualified repair... - Page 6 • Ensure that the machine is always fixed to a bench, • Note the direction of rotation of the motor and the blade. whenever possible. • Do not lock the movable guard in the open position and • Always stand to one side when operating the saw. always ensure that it is working properly, freely rotating and returning to fully cover the teeth of the blade.
-
Page 7: Accessories
30mA or less. Wear goggles Wear ear muffs Wear a breathing mask Accessories The 909 BN210 Compound Mitre Saw is supplied with the following accessories as standard: • Saw blade (fitted) • 6mm Hex key •... -
Page 8: Know Your Product
Know your product Before using the saw, familiarise yourself with all the operating features and safety requirements. 1. Saw arm 12. Mitre table 2. Release knob 13. Mitre scale 3. Operating handle 14. Table insert (kerf plate) 4. Upper fixed blade guard 15. -
Page 9: Unpacking
Due to modern mass production techniques, it is unlikely The saw base has holes in that your 909 Power Tool is faulty or that a part is missing. each corner to facilitate bench If you find anything wrong, do not operate the tool until the mounting (Fig. -
Page 10: Mitre Table Locks
Mitre table locks Spindle lock button The mitre table locks (15) are The spindle lock button (18) used to lock the table at the prevents the blade in the desired mitre angle saw from rotating (Fig. F). (Fig. D1 - D2). Depress and hold the spindle lock button while installing, The mitre saw cuts from 0°... -
Page 11: Setting The Table Square With The Blade
11. Use an 8mm wrench Setting the table square with the blade or adjustable wrench 1. Make sure that the electrical plug is removed from the to loosen the lock nut power point. securing the 0° bevel 2. Push the saw arm (1) down to its lowest position and adjustment screw (10). -
Page 12: Setting The Fence Square With The Table
It will prevent the blade screw from properly securing the Setting the fence square with the table blade on the spindle. Do not use the saw to cut metal or 1. Make sure that the electrical plug is removed from the masonry. -
Page 13: Operation
7. Hold the rotating guard (5) 14. Use the 6mm hex key to tighten the blade bolt securely up and press the spindle (tighten in an anti-clockwise direction). lock button (18). Rotate the 15. Lower the blade guard, hold the rotating lower blade blade until the spindle locks guard (5) and blade bolt cover (19) in position and (Fig. -
Page 14: Bevel Cut
4. Retighten the mitre locks (15). WARNING. Be sure to tighten the mitre locks before making a cut. Failure to do so could result in the table moving during WARNING. Be sure to tighten the mitre locks before making the cut and cause serious personal injury. a cut. -
Page 15: Compound Mitre Cut
10. Press the release latch (17) and slowly lower the blade Compound mitre cut into and through the workpiece. A compound mitre cut involves using a mitre angle and a 11. Release the switch trigger (16) and allow the saw bevel angle at the same time.
Need help?
Do you have a question about the BN210 and is the answer not in the manual?
Questions and answers