Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lenovo 8097
Summary of Contents for Lenovo 8097
- Page 1 User Guide Types 8097, 8143, 8144, 8146 Types 8422, 8423, 8427...
- Page 3 User Guide Types 8097, 8143, 8144, 8146 Types 8422, 8423, 8427...
- Page 4 RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in...
-
Page 5: Table Of Contents
Password protection Changing the battery . Erasing a lost or forgotten password (clearing CMOS) . © Lenovo 2005. Portions © IBM Corp. 2005. Replacing the cover and connecting the cables . Chapter 2. Using the Setup Utility . vi . vi program . - Page 6 User Guide...
-
Page 7: Important Safety Information
In the unlikely event that you notice any of the conditions listed below, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can © Lenovo 2005. Portions © IBM Corp. 2005. ™ Statement of Limited Warranty. -
Page 8: General Safety Guidelines
Note: If you notice these conditions with a product (such as an extension cord) that is not manufactured for or by Lenovo, stop using that product until you can contact the product manufacturer for further instructions, or until you get a suitable replacement. -
Page 9: Power Cords And Power Adapters
Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Power cords and power adapters Use only the power cords and power adapters supplied by the product manufacturer. -
Page 10: Plugs And Outlets
In addition many mobile products such as ThinkPad notebook PCs utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts. -
Page 11: Heat And Product Ventilation
Heat and product ventilation Computers generate heat when turned on and when batteries are charging. Notebook PCs can generate a significant amount of heat due to their compact size. Always follow these basic precautions: v Do not leave the base of your computer in contact with your lap or any part of your body for an extended period when the computer is functioning or when the battery is charging. -
Page 12: Additional Safety Information
v Check CD/DVD discs for cracks before each use. Do not use cracked or damaged discs Additional safety information Danger Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. -
Page 13: Modem Safety Information
Do not use the telephone to report a gas leak in the vicinity of the leak. Laser compliance statement Some personal computer models are equipped from the factory with a CD-ROM drive or a DVD-ROM drive. CD-ROM drives and DVD-ROM drives are also sold separately as options. -
Page 14: Power Supply Statement
Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. -
Page 15: Overview
Downloads and drivers v Links to other useful sources of information To access this information, point your browser to: http://www.lenovo.com/think/support © Lenovo 2005. Portions © IBM Corp. 2005. ® program, on your desktop, provides a link to more information xiii... - Page 16 User Guide...
-
Page 17: Chapter 1. Installing Options
Before you install or remove any option, read “Important safety information” on page v. These precautions and guidelines will help you work safely. Note: Use only the parts provided by Lenovo. Features This section provides an overview of the computer features and preinstalled software. - Page 18 Memory v Support for four double data rate (DDR or DDR2, depending on model) dual inline memory modules (DIMMs) v 512 KB flash memory for system programs Internal drives v 3.5-inch, slim, 1.44 MB diskette drive v Serial Advanced Technology Attachment (SATA) internal hard disk drive v Optical drive (some models) Video subsystem v An integrated graphics controller for a Video Graphics Array (VGA) monitor...
- Page 19 Expansion v Five drive bays v Two standard peripheral component interconnect (PCI) adapter connectors v One PCI Express x1 adapter connector v One PCI Express x16 graphics adapter connector Power v 310 W power supply with manual voltage selection switch v Automatic 50/60 Hz input frequency switching v Advanced Power Management support v Advanced Configuration and Power Interface (ACPI) support...
-
Page 20: Available Options
You can also obtain information by calling the following telephone numbers: v Within the United States, call 1-800-426-2968, your Lenovo reseller, or Lenovo marketing representative. v Within Canada, call 1-800-565-3344 or 1-800-426-2968. v Outside the United States and Canada, contact your Lenovo reseller or Lenovo marketing representative. User Guide... -
Page 21: Specifications
Specifications This section lists the physical specifications for your computer. Dimensions Height: 492 mm (19.4 in.) Width: 175 mm (6.9 in.) Depth: 450 mm (17.7 in.) Weight Minimum configuration: 10.5 kg (23 lb) Maximum configuration: 13.5 kg (30 lb) Environment Air temperature: System on: 10°... -
Page 22: Tools Required
Tools required To install some options in your computer, you might need a flat-blade or Phillips screwdriver. Additional tools might be needed for certain options. See the instructions that come with the option. Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components and options. -
Page 23: Locating The Connectors On The Front Of Your Computer
Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer. Note: Not all computer models will have the following connectors. IEEE 1394 connector USB connector USB connector Microphone connector Headphone connector Chapter 1. -
Page 24: Locating The Connectors On The Rear Of Your Computer
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. Diagnostic LEDs Voltage selection switch Power connector Audio line out connector Audio line in connector VGA monitor connector Parallel connector Serial connector (COM 1) PS/2 mouse connector... -
Page 25: Obtaining Device Drivers
Audio line in connector Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http://www.lenovo.com/think/support on the World Wide Web. Installation instructions are provided in README files with the device-driver files. Description Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. -
Page 26: Removing The Cover
Removing the cover Important Read “Important safety information” on page v and “Handling static-sensitive devices” on page 6 before removing the computer cover. To remove the computer cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. -
Page 27: Locating Components
Locating components The following illustration will help you locate the various components in your computer. Memory modules Power supply Hard disk drive PCI adapter connector Optional PCI adapter Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. -
Page 28: Installing A Memory Module
The following illustration shows the locations of parts on the system board. 12V power connector Diskette drive connector Speaker connector Memory module connector 4 Memory module connector 3 Memory module connector 2 Memory module connector 1 Clear CMOS/Recovery jumper Front Panel connector PATA IDE connector SATA 4 IDE connector SATA 3 IDE connector... - Page 29 To determine the type of memory required: 1. Remove the computer cover. See “Removing the cover” on page 10. 2. Locate the memory module connectors. See “Identifying parts on the system board” on page 11. v If the two memory module connectors closest to the edge of the board are a yellow color, your system board has DDR type memory.
-
Page 30: Installing Adapters
Installing adapters This section provides information and instructions for installing and removing adapters. Your computer has four expansion connectors. There are two connectors for PCI adapters, one for a PCI Express x16 adapter, and one for a PCI Express x1 adapter. -
Page 31: Installing Internal Drives
5. Close the adapter latch to secure the adapter. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 24. Installing internal drives This section provides information and instructions for installing and removing internal drives. -
Page 32: Drive Specifications
Drive specifications Your computer comes with the following factory-installed drives: v An optical drive in bay 1 (some models) v A 3.5-inch diskette disk drive in bay 4 (preinstalled in some models) v A 3.5-inch hard disk drive in bay 5 Any bay that does not have a drive installed has a static shield and bay panel installed. -
Page 33: Installing A Drive In Bay 1 Or Bay 2
Installing a drive in bay 1 or bay 2 1. Remove the computer cover. See “Removing the cover” on page 10. 2. Remove the front bezel by pushing the blue release button as shown. 3. Remove the static shield from the drive bay by using a flat-blade screwdriver to gently pry it loose. -
Page 34: Installing A Hard Disk Drive In Bay 3
v If there is a combination of optical and parallel ATA hard disk drives in bays 1 and 2, set the hard disk drive as a master device and the optical drive as a slave device. Refer to the documentation that comes with your drive for master/slave jumper information. - Page 35 2. Remove the front bezel by pushing the blue release button as shown. 3. Remove the knockout from drive bay 3 by using a flat-blade screwdriver to pry it loose. 4. PATA drives must be jumpered as either a master or a slave device. SATA hard disk drives do not require either a master or a slave device jumper.
-
Page 36: Connecting Drives
6. Install a retainer bracket on the side of the drive. 7. Install the drive into the bay until it snaps into position. 8. Continue at “Connecting drives.” Connecting drives The steps to connect a drive are different depending on the type of drive. Use one of the following procedures for your drive connection. -
Page 37: Connecting An Additional Optical Drive, Or Parallel Ata Hard Disk Drive
Connecting an additional optical drive, or parallel ATA hard disk drive 1. Locate the extra connector on the three-connector signal cable that is attached to the PATA IDE connector on the system board. See “Identifying parts on the system board” on page 11. 2. -
Page 38: Padlock
Padlock Your computer is equipped with a padlock loop such that the cover cannot be removed when a padlock is installed. Make sure that the padlock you install does not interfere with computer cables. Password protection To deter unauthorized use of your computer, you can use the Setup Utility program to set passwords. -
Page 39: Erasing A Lost Or Forgotten Password (Clearing Cmos)
Refer to “Lithium battery notice” on page x for information about replacing and disposing of the battery. To change the battery: 1. Turn off the computer and all attached devices. 2. Remove the computer cover. See “Removing the cover” on page 10. 3. -
Page 40: Replacing The Cover And Connecting The Cables
7. Restart the computer, leave it on for approximately 10 seconds. Turn off the computer by holding the power switch for approximately 5 seconds. The computer will turn off. 8. Repeat steps 2 through 4 on page 23. 9. Move the jumper back to the standard (pins 1 and 2). 10. -
Page 41: Chapter 2. Using The Setup Utility Program
Password considerations If you are setting any of the various types of passwords on your computer, you should read and understand the following information: © Lenovo 2005. Portions © IBM Corp. 2005. -
Page 42: User Password
v If you type an incorrect password, you will see an error message. If you type an incorrect password three consecutive times, you must turn the computer off and start again. v If you set both a User Password and an IDE Drive User Password to the same string, you will be prompted for the password only once when you turn on your computer. -
Page 43: Setting, Changing, And Deleting A Password
Attention Make sure that the IDE Drive Master password is stored in a safe place. If both the IDE Drive User password and the IDE Drive Master password are lost or forgotten, the IDE hard disk drive must be replaced. If both the IDE Drive User Password and the IDE Drive Master Password are to be set, the IDE Drive Master Password must be set before setting the IDE Drive User Password. -
Page 44: Selecting A Temporary Startup Device
Selecting a temporary startup device Use this procedure to startup from any boot device. Note: Not all CDs, hard disks, and diskettes are startable (bootable). Turn off your computer. 2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key. -
Page 45: Appendix A. Updating System Programs
8. Follow the instructions on the screen to complete the update. Updating (flashing) BIOS from your operating system Note: Due to constant improvements being made to the Lenovo Web site, Web page content (including the links referenced in the following procedure) is subject to change. -
Page 46: Recovering From A Post/Bios Update Failure
1. From your browser, type http://www.lenovo.com/think/support in the address field and press Enter. 2. Locate the Downloadable files for your machine type as follows: a. In the Use Quick path field, type in your machine type and click Go. b. Under Browse by product, click Continue. -
Page 47: Appendix B. Cleaning The Mouse
1. Turn off your computer. 2. Turn the mouse over, with the top side down, and look carefully at the bottom. Twist the retainer ring 1 to the unlocked position to remove the ball. © Lenovo 2005. Portions © IBM Corp. 2005. - Page 48 3. Place your hand over the retainer ring and ball 2 , and then turn the mouse over, top side up, so that the retainer ring and ball fall out into your hand. 4. Wash the ball in warm, soapy water then dry it with a clean cloth. Blow air carefully into the ball cage 4 to dislodge dust and lint.
-
Page 49: Appendix C. Manual Modem Commands
Basic AT commands In the following listings, all default settings are printed in bold text. Command DS=n © Lenovo 2005. Portions © IBM Corp. 2005. Function Manually answer incoming call. Repeat last command executed. Do not precede A/ with AT or follow with ENTER. - Page 50 Command Sr=n User Guide Function Force modem off-hook (make busy) Note: H1 command is not supported for Italy Display product-identification code Factory ROM checksum test Internal memory test Firmware ID Reserved ID Low speaker volume Low speaker volume Medium speaker volume High speaker volume Internal speaker off Internal speaker on until carrier detected...
-
Page 51: Extended At Commands
Extended AT commands Command &C_ &D_ &F_ &G_ &K_ &M_ &P_ &R_ &S_ &T_ &V Function &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command... -
Page 52: Mnp/V.42/V.42Bis/V.44 Commands
Command &W_ +MS? +MS=? +MS=a,b,c,e,f MNP/V.42/V.42bis/V.44 commands Command &Q_ +DS44=0, 0 +DS44=3, 0 +DS44? +DS44=? User Guide Function &V1 Display Last Connection Statistics &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 Disable auto-retrain Enable auto-retrain Displays the current Select Modulation settings... -
Page 53: Fax Class 1 Commands
Fax Class 1 commands +FAE=n +FCLASS=n +FRH=n +FRM=n +FRS=n +FTH=n +FTM=n +FTS=n Fax Class 2 commands +FCLASS=n +FAA=n +FAXERR +FBOR +FBUF? +FCFR +FCLASS= +FCON +FCIG +FCIG: +FCR +FCR= +FCSI: +FDCC= +FDCS: +FDCS= +FDIS: +FDIS= +FDR +FDT= +FDTC: +FET: +FET=N +FHNG +FLID= +FLPL +FMDL? -
Page 54: Voice Commands
+FPHCTO +FPOLL +FPTS: +FPTS= +FREV? +FSPT +FTSI: Voice commands #BDR #CID #CLS #MDL? #MFR? #REV? #VBQ? #VBS #VBT #VCI? #VLS #VRA #VRN #VRX #VSDB #VSK #VSP #VSR #VSS #VTD #VTM #VTS #VTX User Guide Phase C time out. Indicates polling request. Page transfer status. - Page 55 Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix C.
- Page 56 User Guide...
-
Page 57: Appendix D. Notices
Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk. -
Page 58: Television Output Notice
Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo PS/2 ThinkCentre... -
Page 59: Index
Ethernet connector 9 hard disk drive security 25 important safety information v information resources xiii input/output (I/O) features 2 © Lenovo 2005. Portions © IBM Corp. 2005. installing options adapters 14 external 6 memory 12 memory modules 12 security features 21... - Page 60 recovering from a POST/BIOS update failure 30 removing the cover 10 replacing the cover 24 SATA connectors 12 security features 3, 21 hard disk drive 25 padlock 22 security profile by device 27 serial connector 9 setup utility 25 Setup Utility 25 system board connectors 12 identifying parts 11...
- Page 62 Part Number: 19R0450 Printed in USA (1P) P/N: 19R0450...