Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cyrus Mono X 200 Signature
Summary of Contents for Cyrus Mono X 200 Signature
- Page 1 ENGINEERED TO ENTERTAIN...
-
Page 2: Table Of Contents
Cyrus Mono X 200 Signature & Mono X 300 Signature User Instructions CONTENTS IMPORTANT! Read before operating this equipment! ....... 1 Power supply: ................1 Servicing: ..................1 Product service centres: ............... 1 WElCOME TO ThE WORld Of CyRuS! ..........2 Preparations for Installation ............ -
Page 3: Important! Read Before Operating This Equipment
RETAIN INSTRuCTIONS: The safety and operating instructions should be The mains supply requirement for your Cyrus Mono X Signature is marked retained for future reference. on a label on the rear panel. Before connecting, check that this voltage is fOllOW INSTRuCTIONS: All operating and use instructions should be the same as your mains supply. -
Page 4: Welcome To The World Of Cyrus
• 2 MC-BUS cables Now is a good time to register your new Cyrus product. Registration takes After removing these items, please retain the packaging. only a few minutes, brings the added benefit of a full two year factory... -
Page 5: Placement
Connecting to the AC Mains Supply If in doubt about the correct cable to choose, any Cyrus retailer will be Connect the socket on the AC Power cable to the Power inlet h on the able to advise. -
Page 6: Chain Output
Cyrus Mono X 200 Signature & Mono X 300 Signature User Instructions Chain Output Gain Matching The Chain output f allows more than one Mono X Signature to be All Cyrus power amplifiers, and all power amplifier stages in Cyrus connected to each channel of a pre-Amplifier or decoder. -
Page 7: Remote Power Control (Mc-Bus, Rs232 Or 12V Trigger)
Signature MC-BUS out MC-BUS in Cyrus Mono X Signature MC-BUS out MC-BUS in With MC-BUS established you can control the power function of the system from the front panel or remote control of the main Cyrus amplifier or Surround Processor. -
Page 8: Operation
Cyrus Mono X 200 Signature & Mono X 300 Signature User Instructions OPERATION INPUT Zero Feedback Mono X Key to the front panel drawing Standby key Standby indicator Input indicator Input selector key Power Control Input Indicator When power is first applied, the amplifier will initialise, then set to The INPUT Indicator c will glow red when the output of the Mono X Standby. -
Page 9: Cooling
Cyrus Mono X 200 Signature & Mono X 300 Signature User Instructions Cooling TROuBlEShOOTING GuIdE If your Mono X Signature is not operating properly, disconnect the power Cooling in use and check all connections using the notes in this handbook. If problems Due to the substantial power of the Mono X Signature, forced air-cooling persist, the checklist below may be helpful. -
Page 10: Specifications
Slew Rate (input filter bypassed) ..........700v/μS Frequency Response (-3dB) ..........0.1Hz-300kHz S/N Ratio (Ref. 150W / 8Ω) ............114dBA Chain Output (buffered) ..........(unity gain) 660mV (ref. 660mV RCA input, 1.3V Balanced input.) Cyrus reserves the right to change all specifications without notice. E & OE... -
Page 11: Warranty
Cyrus Mono X 200 Signature & Mono X 300 Signature User Instructions WARRANTy The warranty should be registered on-line within 8 days of purchase. No Dealer or Distributor may vary the terms of this warranty, which is personal to the original Purchaser and is not transferable. - Page 12 Cyrus Audio Ltd., Ermine Business Park, Huntingdon, PE29 6XY, U.K.
Need help?
Do you have a question about the Mono X 200 Signature and is the answer not in the manual?
Questions and answers