3 7 63 1515 0 SERVICE MANUAL DVD/CD RECEIVER MA158 2005 KD-DV6105,KD-DV6108 KD-DV6105 Area suffix UT ------------------------- Taiwan UN --------------------------Asean U -------------------- Other Areas KD-DV6108 Area suffix L 13942296513 A ------------------------ Australia UN --------------------------Asean TABLE OF CONTENTS PRECAUTIONS ............... 1-3 SPECIFIC SERVICE INSTRUCTIONS .
http://www.xiaoyu163.com 3 7 63 1515 0 SPECIFICATION AUDIO AMPLIFIER SECTION Maximum Power Output Front 50 W per channel Rear 50 W per channel 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more Continuous Power Output (RMS) Front than 0.8% total harmonic distortion.
http://www.xiaoyu163.com SECTION 1 3 7 63 1515 0 PRECAUTIONS Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 4
http://www.xiaoyu163.com Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Page 5
http://www.xiaoyu163.com Important for laser products 3 7 63 1515 0 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated.
http://www.xiaoyu163.com SECTION 2 3 7 63 1515 0 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. L 13942296513 u163 1-6 (No.MA158) http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 3 3 7 63 1515 0 DISASSEMBLY Main body section 3.1.1 Removing the front panel assembly (See Fig.1) Push the detach button in the lower left part of the front panel as- sembly and remove the front panel assembly. Front panel assembly Detach button Fig.1...
Page 8
http://www.xiaoyu163.com 3.1.3 Removing the front chassis assembly 3 7 63 1515 0 (See Figs.3 and 4) • Remove the front panel assembly and bottom cover. (1) From the front side of the main body, remove the two Front chassis assembly screws A attaching the front chassis assembly.
Page 9
http://www.xiaoyu163.com 3.1.5 Removing the rear bracket 3 7 63 1515 0 (See Fig.6) • Remove the bottom cover. (1) From the back side of the main body, remove the two Slot LINE IN cable SUBWOOFER cable screws E, two screws E', screw F, two screws G and three screws H attaching the rear bracket.
http://www.xiaoyu163.com 3.1.8 Removing the main sub board 3 7 63 1515 0 (See Figs.9 to 11) • Remove the front panel assembly, bottom cover, front chassis assembly, side heat sink, main board and DVD mechanism as- DVD mechanism assembly sembly. (1) From the top side of the DVD mechanism assembly, re- move the two screws L attaching the dust cover.
Page 11
http://www.xiaoyu163.com 3.1.9 Removing the switch board 3 7 63 1515 0 (See Figs. 12 to 14) • Remove the front panel assembly. (1) From the back side of the front panel assembly, remove the Rear cover five screws P attaching the rear cover. (See Fig.12.) (2) Release the ten joints i attaching the rear cover to the front panel assembly.
Page 12
http://www.xiaoyu163.com DVD mechanism assembly 3 7 63 1515 0 3.2.1 Removing the mechanism control board (See Fig.1) Caution: Before disconnecting the flexible wire extending from the DVD Lug wire Flexible wire pickup, solder the short-circuit point on the flexible wire using Feed motor a grounding soldering iron.
Page 13
http://www.xiaoyu163.com 3.2.2 Removing the top cover 3 7 63 1515 0 (See Fig.2) (1) Remove the two screws D attaching the top cover on the back of the body. (2) Remove the top cover upward. Reference: When reassembling, set part b of the top cover under the bending part c of the chassis frame.
Page 14
http://www.xiaoyu163.com 3.2.4 Removing the clamper unit 3 7 63 1515 0 (See Fig.5 to 7) • Remove the top cover and the mechanism section. (1) Remove the clamper2 spring on the bottom of the mecha- Clamper2 spring nism section. (See Figs.5.and 6.) (2) Release the part d of the clamper spring from the bending part of the chassis base assembly.
Page 15
http://www.xiaoyu163.com 3 7 63 1515 0 Clamper unit Clamper spring Fig.8 Clamper unit L 13942296513 Notch Fig.9 u163 (No.MA158)1-15 http://www.xiaoyu163.com...
Page 16
http://www.xiaoyu163.com 3.2.6 Removing the front unit 3 7 63 1515 0 (See Fig.10 to 12) • Remove the top cover and the mechanism section. (1) Disconnect the flexible wire from connector CN202 on the mechanism control board at the bottom of the body. (See Front unit Fig.10.) (2) Remove the screw G attaching the front unit on the top of...
Page 17
http://www.xiaoyu163.com 3.2.7 Removing the loading arm assembly 3 7 63 1515 0 (See Fig.13 , 14) • Remove the top cover, the mechanism section and the front unit. (1) From the top of the body, move the loading arm assembly from the front side upward, and release the bosses from the right and left joints k and m of the chassis base assem- bly.
Page 18
http://www.xiaoyu163.com 3.2.8 Removing the rod (L)(R)/roller assembly 3 7 63 1515 0 (See Fig.15 and 16) • Remove the top cover, the mechanism section, the front unit and the loading arm assembly. Collar Collar (1) Release the rod (L) and (R) from the joints q at the bottom of the loading arm assembly (See Fig.15.) (2) Remove the roller assembly from the loading arm assem- bly.
Page 19
http://www.xiaoyu163.com 3.2.9 Removing the DVD pickup assembly 3 7 63 1515 0 (See Fig.17 to 19) • Remove the mechanism control board. (1) From the bottom of the body, turn the feed gear in the di- Feed gear rection of the arrow to move the DVD pickup outwards. (See Fig.17.) (2) Remove the screw J attaching the thrust spring.
Page 20
http://www.xiaoyu163.com 3.2.10 Removing the spindle motor 3 7 63 1515 0 (See Fig.20) • Remove the mechanism control board. Remove the two screws L attaching the spindle motor on the Spindle motor bottom of the body. Caution: Perform adjustment when reattaching the spindle motor. Fig.20 3.2.11 Removing the feed motor assembly (See Fig.21 and 22)
http://www.xiaoyu163.com SECTION 4 3 7 63 1515 0 ADJUSTMENT Test instruments required for adjustment Standard measuring conditions (1) Digital oscilloscope (100MHz) Power supply voltage DC14.4V(11 to 16V) (2) Jitter meter Load impedance 4Ω(2 Speakers connection) (3) Digital tester Line Output 20KΩ...
Page 22
http://www.xiaoyu163.com After replacing the pickup, set the unit in the service mode to display a jitter value on the LCD. Confirm that the jitter value measured 3 7 63 1515 0 with a jitter meter is within 12% of the jitter value displayed on the LCD. If it is within 12%, then adjustment is not necessary. Please note that a jitter value displayed on the LCD is hex data.
Page 23
http://www.xiaoyu163.com Jitter value conversion table 3 7 63 1515 0 Load the test DVD and set the unit to the service mode. A jitter value converted to the hex value is displayed on the LCD. Refer to the corresponding decimal notation value shown in the following Jitter Conversion Table. The adjustment is OK if the jitter value measured with a jitter meter is within 12% of the jitter value displayed on the LCD.
Page 24
http://www.xiaoyu163.com Service mode 3 7 63 1515 0 4.5.1 Standard input/output conditions Power supply voltage DC14.4V(11 to 16V) Load impedance 4Ω(2 Speakers connection) Line Output 20KΩ 4.5.2 Service mode setting procedure (The DVD does not need to be loaded before starting the following procedure.) [STANDBY/ON ATTENUATOR] button [SEL] button [DISC UP] button...
Page 25
http://www.xiaoyu163.com 4.5.3 Operation procedures 3 7 63 1515 0 Keep this state more than 2 seconds while continuing pressing the [SEL] button, [STANDBY/ON ATTENUATOR] button and [SOURCE] button sequentially. The unit enters the service mode. "INIT ALL" is Initialize all data to the factory setting Press the [SEL] key indicated on the LCD.
Page 26
http://www.xiaoyu163.com 3 7 63 1515 0 "CD ERROR" is Read loading and ejection error history Press the [SEL] key indicated on the LCD. : The error history saved in the system control is read and displayed. TOT-xxxx : Total error count. Total error count (A figure between 0 and 9999 is displayed.
Page 27
http://www.xiaoyu163.com 3 7 63 1515 0 "SYS-TEMP" is Thermistor's temperature data readout Press the [SEL] key indicated on the LCD. : Data in the temperature sensor in the system control is read every 5 seconds and displayed in hex numbers. "CHK MODE"...
Page 28
http://www.xiaoyu163.com 4.5.4 DVD unit check mode 3 7 63 1515 0 Change LCD indication with a [FF ] button and a [REW ] button. Check item list Example of A/D key DVD unit operation Indication contents LCD indication Start at normal speed NORMPLAY (After start, it is measured JITTER on the Laser current value...
http://www.xiaoyu163.com SECTION 5 3 7 63 1515 0 TROUBLESHOOTING 16 PIN CORD DIAGRAM Black Green GN/BK WH/BK Violet VI/BK GY/BK Gray Blue White Yellow Orange Brown BL/WH Yellow Green OR/WH 1 BK MEMORY 16 YL 2 RD 15 OR/WH ILLUMINATION CONTROL L 13942296513 9 WH...
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA158) Printed in Japan http://www.xiaoyu163.com...
Page 31
3 7 63 1515 0 SCHEMATIC DIAGRAMS DVD/CD RECEIVER KD-DV6105,KD-DV6108 CD-ROM No.SML200502 KD-DV6105 Area suffix UT ------------------------- Taiwan UN --------------------------Asean U -------------------- Other Areas L 13942296513 KD-DV6108 Area suffix A ------------------------ Australia UN --------------------------Asean Contents Block diagram Standard schematic diagrams...
http://www.xiaoyu163.com 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 40
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MA158SCH) http://www.xiaoyu163.com...
3 7 63 1515 0 PARTS LIST [ KD-DV6105 ] [ KD-DV6108 ] * All printed circuit boards and its assemblies are not available as service parts. KD-DV6105 Area suffix UT -----------------------------Taiwan UN --------------------------Asean U -------------------- Other Areas L 13942296513...
Page 42
http://www.xiaoyu163.com 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. Switch board L 13942296513 Main sub board u163 http://www.xiaoyu163.com...
Page 43
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 Main board u163 http://www.xiaoyu163.com...
Page 44
http://www.xiaoyu163.com 3 7 63 1515 0 General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local LV10774-004A TOP CHASSIS LV40848-044A SPACER(P) LV34061-001A SIDE HEAT SINK QYSDST2003ZA TAP SCREW M2 x 3mm(x2) QYSDST2606ZA TAP SCREW M2.6 x 6mm(x2) QYSDST2604ZA TAP SCREW M2.6 x 4mm(x3)
Page 45
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local GE31683-011A LABEL (DVD) DV6105U,DV6105UN,DV6105UT,DV6108UN QLD0354-001 LCD MODULE QNZ0772-001 RUBBER CONN QUQ105-4510AD-E FFC WIRE 45pin 10cm QAM0680-001 HP CABLE QAM0685-001 LINE IN CABLE QAM0683-001 COMPOSITE CABLE QAM0684-001 SUBWOOFER CABLE VYTA500-001...
Page 46
http://www.xiaoyu163.com 3 7 63 1515 0 DVD mechanism assembly and parts list Block No. Grease FMU-JD4-1D = JVS-1003 = MOBIL-1 = JVG-31N = JC-803B = 1401C BACK SIDE L 13942296513 AFTER SET PICK UP SA. APPLY GREASE u163 INSIDE The parts without symbol number are not service. http://www.xiaoyu163.com...
Page 47
http://www.xiaoyu163.com 3 7 63 1515 0 DVD mechanism Block No. [M][J][M][M] Symbol No. Part No. Part Name Description Local VKZ4539-026 MINI SCREW (x2) QYSPSFT2040Z TAP SCREW M2 x 4mm LV43481-001A COOLING RUBBER (x2) LV10674-001A CHASSIS FRAME LV30225-0J6A SPACER (x2) VKZ4539-056 MINI SCREW VYSA1R4-056...
Page 48
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local LV43010-001A L.S.GEAR LV43063-001A L.S.COLLAR LV43011-001A THRUST SPRING QYSPSFT2040Z TAP SCREW M2 x 4mm LV33624-001A HOLDER(M) VKZ4539-026 MINI SCREW (x2) LV21288-001A HOLDER(S) VKZ4539-026 MINI SCREW (x2) LV43064-001A ROD(M) LV43065-001A...
http://www.xiaoyu163.com 3 7 63 1515 0 Electrical parts list Main board Symbol No. Part No. Part Name Description Local Block No. [0][1] D401 RB160M-30-X SB DIODE Symbol No. Part No. Part Name Description Local D421 MA111-X SI DIODE D431 MA111-X SI DIODE...
Page 50
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C103 QEKJ0JM-476Z E CAPACITOR 47uF 6.3V M C413 QCZ0202-155Z C CAPACITOR 1.5uF 25V Z C109 NCB31EK-223X C CAPACITOR 0.022uF 25V K C414...
Page 51
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C962 QEKJ1AM-227Z E CAPACITOR 220uF 10V M R305 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J C963 QEKJ1AM-227Z E CAPACITOR 220uF 10V M R306...
Page 52
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R437 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R781 NRSA63J-471X MG RESISTOR 470Ω 1/16W J R438 NRSA63J-472X MG RESISTOR 4.7kΩ...
Page 53
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local CN411 QGA2501F1-02 CONNECTOR W-B (1-2) R605 NRSA63J-272X MG RESISTOR 2.7kΩ 1/16W J CN421 QGA2501C3-03Z CONNECTOR W-B (1-3) R606 NRSA63J-392X MG RESISTOR...
Page 54
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local S610 NSW0206-001X TACT SWITCH C212 NCB31CK-104X C CAPACITOR 0.1uF 16V K S611 NSW0206-001X TACT SWITCH C213 NCB31CK-104X C CAPACITOR 0.1uF 16V K...
Page 55
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C411 NCB31CK-104X C CAPACITOR 0.1uF 16V K R307 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J C412 NBE41AM-476X TA E CAPACITOR 47uF 10V M R308...
Page 56
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local R437 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R438 NRSA63J-223X MG RESISTOR 22kΩ 1/16W J R441 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R442 NRSA63J-0R0X MG RESISTOR 0Ω...
Page 58
http://www.xiaoyu163.com 3 7 63 1515 0 Packing materials and accessories parts list Block No. A1,A3,A4 L 13942296513 KIT: A5,A6,A7, A8,A9,A10 u163 3-18 http://www.xiaoyu163.com...
Page 59
http://www.xiaoyu163.com 3 7 63 1515 0 Packing and Accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local GET0278-007A INST BOOK ENG,CHI(TAIWAN) DV6105UT GET0278-001A INST BOOK ENG,CHI(TAIWAN) DV6105U,DV6108A GET0278-003A INST BOOK ENG,INA DV6105UN,DV6108UN GET0278-002A INST BOOK KOR,THA,ARA,PER DV6105U,DV6108A GET0278-006A INSTALL MANUAL...