2gig Technologies Go!Control Panel Installation & Programming Manual

Wireless security system

Hide thumbs Also See for Go!Control Panel:

User manual (52 pages)

Installation and programming technical training (110 pages)

User manual (20 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual See also: User Manual

Go!Control Panel

Installation & Programming Guide

Firmware Version 1.12

ENGLISH

W I R E L E S S

S E C U R I T Y

S Y S T E M

WARNING: OWNER 'S I NS TRUCTION NOTICE

Not to be removed by anyone except occup ant

Table of Contents

Need help?

Do you have a question about the Go!Control Panel and is the answer not in the manual?

Questions and answers

Summary of Contents for 2gig Technologies Go!Control Panel

Page 1 Go!Control Panel Installation & Programming Guide Firmware Version 1.12 ENGLISH W I R E L E S S S E C U R I T Y S Y S T E M WARNING: OWNER ’S I NS TRUCTION NOTICE Not to be removed by anyone except occup ant...
Page 2 THIS PAGE INTENTIONALLY LEFT BLANK...
Page 3: Table Of Contents
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 About the 2GIG Go!Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing the System in Residential Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing the System in Commercial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Optional Features and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 External Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Internal Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Wireless Installation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Sensors and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Wireless System Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4 Go!Control Wireless Security System | Installation and Programming Guide Wired Sensor Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Q2: Wired Sensor Programming Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Summary of Wired Sensor # Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Wired Sensor Programming Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Q2: Select Wired Sensor # (1‐2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Q: Select Wired Sensor# Dialer Delay (0 to 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Q: Construct Wired Sensor # Voice Descriptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Q: Select Wired Sensor# Reports (0 to 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Q: Select Wired Sensor# Chime (00 to 13) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Wireless (RF) Key Fob Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Key Fob Programming Outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Summary of RF Key Fob # Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 RF Key Fob Programming Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 5 Q51: Manual Bypass Reports to CS (0‐1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Q52: AC Loss Reports to CS (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Q53: System Low Battery Reports to CS (0‐1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Q54: RF Low Battery Reports to CS (0‐1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Q55: Opening Reports to CS (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Q56: Closing Reports to CS (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Q57: Alarm Restore Reports to CS (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q58: Trouble Restore Reports to CS (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q59: Bypass Restore Reports to CS (0‐1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q60: AC Restore Reports to CS (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q61: System Low Battery Restore Reports to CS (0‐1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q62: RF Low Battery Restore Reports to CS (0‐1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q63: Phone Fail Detect (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q64: Smart Test Reports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Q65: RF Jam Causes Trouble (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Q66: Daylight Saving (0‐1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Q67: Daylight Saving Start Month (01‐12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Q68: Daylight Saving Start Monday (1‐7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 7: About This Guide
INTRODUCTION ABOUT THIS GUIDE This guide provides distributors, dealers, and authorized installation personnel with information about installing, testing, and maintaining the 2GIG Go!Control system. 2GIG by Linear products are not sold directly to consumers and can only be obtained from authorized distribution channels. For a list of authorized distributors, visit: http://www.2gig.com/find‐a‐ distributor. ABOUT THE 2GIG GO!CONTROL SYSTEM Depending on the options set during the installation, the 2GIG Go!Control system has the ability to provide three forms of protection: burglary, fire, and emergency, The system consists of the 2GIG Control Panel, wireless sensors for perimeter and interior burglary protection, and wireless smoke and carbon monoxide detectors. In addition, optional remote control key fobs, wireless panic buttons, and keypads may also be installed. The system monitors all protection sensor types (a.k.a., “zones”) and the system’s status. The Control Panel displays monitoring information and controls the alarm siren. The system can also be setup to send alarm and status reports to a Central Station and has the capability for two (2)‐way voice communications with the Remote Service Provider (RSP). When a security system is installed, insurers may offer discounts on the homeowners’ or renters’ insurance policy. Although the requirements and discount credits vary for each different insurer, users can generally save money as the level of protection increases. It is recommended that you inform the end user to check with their insurance agent to determine if the insurer has specific requirements and/or offers any discount(s). IMPORTANT INFORMATION The 2GIG Go!Control security system conforms to the Security Industry Alarm Coalition’s ANSI/SIA CP‐01: Control Panel Standard‐Features for False Alarm Reduction. It also meets the residential security system certification criteria for the ETL Listed Mark. The recommended storage temperature for all Control Panels is ‐10°C to 60°C (14°F to 140°F). For optimal Control Panel use, operation temperature is 0°C to 49°C (32°F to 120°F). No altitude range limitations have been reported while transporting Control Panel. Installing the System in Residential Settings When installing the system in a residential setting, be aware of the following: • Fire warning systems must be installed in accordance with national codes. In the United States, fire warning ...
Page 8: System Features
Go!Control Wireless Security System | Installation and Programming Guide SYSTEM FEATURES The 2GIG Go!Control system offers security protection for your property, 24‐hour emergency monitoring, and can optionally be used for fire detection in the home. Features include: • Full Voice Response. The panel gives clear notifications that indicate system status, zone descriptions, alarms, and emergencies. • Date, Time, and Weather Display.* Scroll through the date, time, and daily weather forecast. Provides the ability to receive messages, including severe weather warnings. • Quick Access. The one touch access buttons allow the quickest help possible in an emergency. The front panel and buttons serve as controls as well as indicators. Pressing the button displays emergency icons on the display for Panic, Fire, and Emergency alarm activation (each has programmable options and can be enabled or disabled). Pressing the button changes the system display to the Home screen • Full Color Touch Screen. Control all system functions with an easy‐to‐use color touch screen puts a wide range of security and home automation controls at your fingertips. • Multiple Arming Options. Secure your home by arming your system “AWAY” or “STAY.” The Quick Arm/Exit and Bypass features offer added convenience. • Home Automation Radio Module. The built in Z‐Wave radio enables various home automation functions including HVAC, appliances, lighting, and lock control. • Two (2)‐way Response Over Cellular.* Two‐way voice lets central station operators listen in and talk to you when a signal is received, ensuring that the proper emergency response personnel will be dispatched if necessary. • Fully Self‐Contained. The fully self‐contained panel contains a backup battery, and allows 32 user codes to monitor up to 48 wireless zones including eight (8) key fobs, four (4) keypads, It also provides two (2) hardwire loops, 15 sensor types (a.k.a., “zones), a supervised bell output, and a programmable solid‐state control output. • Over‐The‐Air (OTA) Updates.* There’s no need to worry about the panel’s software becoming outdated. With the OTA function, the panel can be remotely updated with the latest software. • Remote Control Options.* Always be in control by remotely managing your system from a computer or web‐...
Page 9: Optional Features And Accessories
Introduction Optional Features and Accessories Optional features that can be purchased to enhance the system include: • 2GIG GSM (Cellular) Radio Module. An on‐board digital communicators reports alarms and trouble to a Central Station receiver via the standard telephone network and a two (2)‐way voice communication with the Central Station. It also supports OTA updates and remote control of the system using telephone or a Web‐enabled device through the Internet. • 2GIG 900 MHz Transceiver Module. it sends and receives signals with wireless touch screen keypads and image sensors. Touch screen keypads allow remote control of the system through the same graphic interface design as the 2GIG Control Panel. Note that the 2GIG 900 MHz Transceiver Module, touch screen keypad, and image sensor are only available in some regions. • 2GIG Wireless Touch Screen Keypad. A wall‐mounted, full‐color, touch screen interface that provides many of the same easy‐to‐use keypad functions available on the Control Panel. It is designed for indoor use only and gives users the ability to control lights, thermostats, and door locks, as well as to view the status of every sensor zone. When the 2GIG 900 MHz Transceiver Module is installed in the Control Panel, the system can be programmed to communicate with up to four (4) Wireless Touch Screen Keypads. • 2GIG Go!Control POTS Module. The POTS (Plain Old Telephone Service) module offers the same features and the cellular module only over a land‐line (instead of cellular), such as two (2)‐way‐voice communication with the remote monitoring service. • 2GIG Go!Bridge IP Communicator. The Go!Bridge provides Internet connectivity between the monitoring service’s Central Station and the Go!Control® Panel (requires the 2GIG 900 MHz Transceiver Module and supports automatic firmware updates, provides interactive security services, and increases supervision using signal‐forwarding to the Central Station. • 2GIG Super Switch Takeover Module. The takeover module communicates with the 2GIG Control Panel and is designed to convert up to eight (8) pre‐wired zones to supervised wireless zones. • 2GIG Hardwire Conversion Kit. This kit provides installers with an easy way to convert the zones of a pre‐wired security alarm system to 2GIG wireless zones. The kit includes one (1) Super Switch Takeover Module (Wireless Takeover of an Alarm System, US Patent No. 8,638,218). You can also install two (2) additional modules, which provides installers with the capability to convert up to 24 pre‐wired security zones to wireless zones. Copyright © 2014 Linear LLC...
Page 10: System Configuration
SYSTEM CONFIGURATION This illustration details the entire system configuration (including optional features). See "Optional Features and Accessories" on page 7.12 Figure 1 Complete System Configuration Copyright © 2014 Linear LLC...
Page 11: External Features
CONTROL PANEL FEATURES EXTERNAL FEATURES Figure 2 Control Panel External Features A Alarm Sounder and Speaker Sounds all system local alarms, voice prompts, system sounds, and audio for two (2)‐ way voice communications with the Central Station B Color Display with Touchscreen Shows all system information, status, programming, and functions as the keypad. Display cycles clock, calendar, and weather with an Alarm.com account (press manually to change) C Microphone For voice communication with the Central Station D Emergency Button/Indicator Lights WHITE when enabled for emergency alarms and flashes during emergency alarms E Home Button/Indicator Sensor Status Lights GREEN when all sensors are closed (ready to arm) Not lit when any sensor is open (not ready to arm) Arming Status Lights RED when system is armed Flashes RED during the Entry Delay Alarm Memory Flashes RED during an alarm Flashes RED after an alarm while system is still armed Power Outage Flashes WHITE during power outage (system on battery backup) Flashes GREEN when all sensors are closed (ready to arm)...
Page 12: Internal Features
Go!Control Wireless Security System | Installation and Programming Guide INTERNAL FEATURES Figure 3 Control Panel Internal Features A Backup Battery Pack The standard backup battery that is included with all 2GIG Control Panels does not support UL 985 installations. To comply with the secondary supply requirement in UL 985 Household Fire Warning System Units, you must install the 2GIG Console Battery Pack (2GIG‐BATT2X). B Telephone Jack Used for RJ45 connection to installation's RJ31X telephone jack. See "Optional 2GIG Go!Control POTS Module" on page 16. C Terminal Block Connections for power, solid state output bell, and hardwire loops. D Alternate Power Supply Alternate connection for power. (Plug‐in barrel connector) E J4 Pin Connector Connector for the Firmware Update Cable used to update the firmware version on the Control Panel. F Optional Receiver Module 2GIG Go!Control POTS Module for over‐the‐air communication with the Central Station. . See "Optional 2GIG Go!Control POTS Module" on page 16. G Main Receiver Module Receiver for peripheral device transmissions (or an optional 2GIG 900 MHz Transceiver Module for use with the Wireless Touch Screen Keypad). H POTS Module (Optional) 2GIG Go!Control POTS Module for connecting the lineman's phone (a.k.a., buttset) for monitoring the telephone line. See "Optional 2GIG Go!Control POTS Module" on page 16. I Third‐Hand Hanger Strap Hooks onto mounting plate during installation to hold the Control Panel while wiring.
Page 13: Installation Outline
INSTALLATION OUTLINE Use the following outline in conjunction with this Installation and Programming Guide to guide you through the installation steps. Unpack the system and identify the system components. Create an Installation Floor Plan to determine the best centralized location for the Control Panel. Decide where to best install the wired and/or wireless sensors. Guidelines are available in the Installation Instructions included with each sensor. Identify an unswitched wall outlet to use for the Control Panel’s power supply. (Optional) Install the GSM (Cellular) Radio Module in the Control Panel. See "GSM (Cellular) Radio Module" on page 18. NOTE: (Optional) If installing the 2GIG Go!Control POTS Module, identify or install a USOC. RJ31X telephone jack to connect the module to the phone line. See "Optional 2GIG Go!Control POTS Module" on page 16. Use the Control Panel’s backplate to mark the drywall cutouts for the Control Panel. Then make the cutouts and attach the backplate to the wall. See "Control Panel Mounting Plate" on page 14. Install each of the system’s wireless sensors. If either of the two hardwire loops are going to be used, install the contacts and route the loop wire to the Control Panel’s wall cutout. Install the optional hardwire sounder, and route the connection wire to the Control Panel’s wall cutout. If used, route the telephone line from the RJ31X jack to the Control Panel’s wall cutout. Use the third‐hand hanger strap to hang the Control Panel on the mounting plate. Then connect all wiring to the Control Panel’s terminal block. See "Control Panel Wiring" on page 19 and "Terminal Block Wiring Diagram" on page 20. If you install the 2GIG Go!Control POTS Module, plug the telephone line into the POTS module. See "Optional 2GIG Go!Control POTS Module" on page 16. Plug the backup battery connector into the connector on the circuit board. Swing the Control Panel up, placing the bottom over the lip of the mounting bracket. Push the top of the Control Panel into the mounting bracket until it snaps into place, then secure it with the retaining screw. Plug the power supply into the unswitched wall outlet. Program the system as described in this manual and document any custom setup options for the end user in the space provided in the User Guide. Test the system as described "Installer Testing" on page 68. Educate the end user(s) about basic system operations and provide them with the Control Panel’s User Guide. Copyright © 2014 Linear LLC...
Page 14: Wireless Installation Tips
WIRELESS INSTALLATION TIPS When installing any wireless system, consider certain limitations. Low power wireless transmitter signals do NOT broadcast equally through all types of construction materials. However, the Control Panel does contain a sensitive receiver that typically allows for placement of transmitters in nearly all locations. To determine the best possible placement for wireless sensors, review the following illustration. Figure 4 Wireless Installation Tips Copyright © 2014 Linear LLC...
Page 15: Wireless System Sensors
SENSORS AND ACCESSORIES WIRELESS SYSTEM SENSORS • Thin Door/Window Contact • Recessed Door Contact • Passive Infrared (PIR) Motion Detector • Four (4)‐Button Keyfob Remote • Panic Button Remote • Glass Break Detector • Wireless Smoke/Heat Alarm • Wireless Touch Screen Keypad • Wireless Touch Screen Keypad • Super Switch Takeover Module (Wireless Takeover of an Alarm System, US Patent No. 8,638,218) SYSTEM ACCESSORIES • GSM (Cellular) Radio Module • Internal Antenna • External In‐Wall Antenna • External Attic Mount Antenna • Standard Battery Pack (UL 1023) • Console Battery Pack (UL 985) •...
Page 16: Control Panel Mounting Plate
INSTALLATION CONTROL PANEL MOUNTING PLATE Mount the Control Panel on the wall in a convenient location (or use the optional desk mount). These tools may be required to mount the Control Panel onto the wall: • Screwdriver • Wire Stripper • Staple Gun • Drywall Saw (or equivalent) • Ladder Remove the locking screw from the top of the Control Panel case and remove the mounting plate. Use the mounting plate as a template to mark the wall for the wiring cutout slot. Use a drywall saw to cut the slot. If using the optional GSM (Cellular) Radio Module with an external antenna, remove the plastic knockout labeled “EXTERNAL ANTENNA” on the mounting plate. Mark and cut a slot in the drywall for the external antenna. Attach the mounting plate to the wall using three (3) screws. Figure 5 Control Panel Mounting Plate A Mounting plate B Remove case screw and mounting plate C If using external antenna, remove knockout plate. D Use mounting plate as a template to mark wire cutout hole in dry wall. E Mount plate with three (3) screws. Copyright © 2014 Linear LLC...
Page 17: Wireless Sensors
Installation WIRELESS SENSORS REMOTE ALARM SOUNDER Install wireless sensors in the appropriate location using the The Control Panel provides two (2) terminals for an optional Install Instructions as your guide. Instructions are included connection to a remote electronic alarm sounder. with each wireless sensor. Figure 7 Remote Alarm Sounder HARDWIRE LOOPS Hardwire loops can be programmed either Normally Open (N/O) or Normally Closed (N/C). End‐of‐Line Resistors (EOLR) can also be used to supervise the loops. Only contacts should be used with the hardwire loops. NOTE: The Control Panel does not support powering external devices (PIR’s, etc.). NOTE: Hardwire loops cannot be used for a CO or Fire sensor loop. If either of the two (2) hardwire loops are going to be used, install the contacts and then route the loop wire to the Control Panel’s wall cutout. If end‐of‐line supervision is required for the loop, install a 2.2kΩ resistor (not supplied) as shown in Figure 6 Hardwire Loop Wiring. Wiring Hardwire loops need to be programmed for contact type. Figure 6 Hardwire Loop Wiring WARNING: To avoid damage to the output, do NOT ...
Page 18: Solid State Output
Go!Control Wireless Security System | Installation and Programming Guide SOLID STATE OUTPUT OPTIONAL 2GIG GO!CONTROL POTS The Control Panel provides one (1) solid state output that MODULE can be programmed to activate during various conditions. To use the telephone jack, you must install the 2GIG The output can switch up to 250 mA @ 16 VDC to ground. Go!Control POTS Module. Both the incoming and outgoing telephone line can be connected. NOTE: For ETL Listing, an external DC Backup Power Supply is required for a load connected to Terminal 4. Figure 9 2GIG Go!Control POTS Module NOTE: When the Control Panel is connected with an AC power source, Terminal 1 provides DC Power only. Figure 8 Solid State Output When the digital communicator activates, all local telephones are disconnected to prevent an off‐hook telephone on the premises from blocking the digital communicator’s call. Figure 10 2GIG Go!Control POTS Module Installation This output only functions while the Control Panel is ...
Page 19 Installation See "Wire Size and Length" on page 21 for wire size and IMPORTANT: You must program the module in order to maximum length. use it with the Control Panel. Run a four (4)‐conductor telephone cable from the Figure 11 Control Panel with 2GIG Go!Control POTS Module telephone company’s demarcation point to the Control Panel mounting plate. Install the 2GIG Go!Control POTS Module into the Control Panel. WARNING: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord for phone line communications. At the demarcation point, do the following: Disconnect only the house telephones that are wired to the box output. Do not disturb the telco input “drop” side of the box or any earth grounds. Connect the RED cable wire to the box Ring, and the GREEN cable wire to the box Tip. Connect the BLACK cable wire to the house telephone Ring wire(s), and the YELLOW cable wire to the house telephone Tip wire(s). At the Control Panel, do the following: Connect the cable’s RED wire to the RJ31X jack’s Ring in terminal, and the GREEN wire to the RJ31Xjack’s Tip in terminal. Connect the cable’s BLACK wire to the RJ31X jack’s Ring out terminal, and the YELLOW wire to the RJ31Xjack’s Tip out terminal.
Page 20: Gsm (Cellular) Radio Module
Go!Control Wireless Security System | Installation and Programming Guide GSM (CELLULAR) RADIO MODULE The GSM (Cellular) Radio Module should already be activated by the factory. If not, contact the Remote Service If installing the GSM (Cellular) Radio Module, see below: Provider. For the GSM (Cellular) Radio Module to function, Figure 12 In-Wall Antenna Installation it must be activated before it can be enrolled. Enrollment is accomplished by creating an account with the provider. A GSM (Cellular) Radio Module Connector B End of antenna hangs down inside the wall NOTE: The routing of the antenna wire is critical. You must route the wire exactly as directed or cell radio interference will occur. When using external antennas, plug the antenna connector into the GSM (Cellular) Radio Module. The antenna drops into the wall or mounts in the attic with the cable passing through the slot in the Control Panel’s mounting plate. Figure 13 Attic Antenna Installation A Attic antenna mounted as high as possible B Coaxial cable to Control Panel Copyright © 2014 Linear LLC...
Page 22: Control Panel Wiring
Go!Control Wireless Security System | Installation and Programming Guide Control Panel Wiring BACKUP BATTERY CONNECTION AND POWER SUPPLY WIRING The third‐hand hanging strap allows you to hang the Control Panel on the mounting plate during installation. The backup battery connects to the Control Panel’s circuit board with a two (2)‐pin header assembly. Hang the Control Panel on the mounting plate by the third‐hand hanger strap. The power supply features a two (2)‐position terminal block for connecting the power supply to the Control Panel power Connect the hardwire loop, external sounder, and open terminals (connection wire not included). collector output wiring (if used) to the Control Panel’s terminal block. Locate an unswitched wall outlet for the plug‐in power supply. Plug the telephone line (if used) into the telephone jack on the POTS Module. WARNING: Never connect the power supply to switch‐ controlled outlet. Figure 15 Third-Hand Hanging Strap Route two (2)‐conductor wire from the power supply location to the Control Panel mounting plate. For wire size and maximum length, see "Wire Size and Length" on page 21. Being careful to observe polarity, connect the wire to the power supply’s DC+ and DC‐ terminals. Do NOT plug ...
Page 23: Wire Size And Length
Installation Wire Size and Length To ensure proper operation, do NOT exceed the following maximum length for the wire size installed: Wire Size Maximum Length 22 AWG 55 ft (16.8 m) 20 AWG 85 ft (25.9 m) 22 AWG 2‐pairs 110 ft (33.5 m) (19 AWG equivalent) 18 AWG 135 ft (41.1 m) TIP: To ensure that the appropriate wire size and length is installed, measure the voltage between the power connection terminals at the back of the Control Panel. The voltage measured must not fall below 11 volts DC or the Control Panel may display nuisance “AC Power Loss” messages and send AC Loss Reports to the Central Station. See "Q52: AC Loss Reports to CS (0‐1)" on page NOTE: In the United States, wiring routed inside walls, ceilings, and floors must comply with requirements of ANSI/NFPA 70: National Electrical Code (NEC) and local building codes. For wiring from the output of the 2GIG Class II Power Supply, wiring rated CL2, CL2X, CL2R, or PLTC is recommended to satisfy these requirements. If this wiring is installed in an air plenum (space used for environmental air exchange) it must be rated CL2P (plenum‐rated). Figure 17 Power Supply Wiring A Left Terminal 14 VDC (+) C 14 VDC (+) Terminal 1 B Right Terminal 14 VDC (‐)
Page 24: Control Panel And Power Supply Mounting
Go!Control Wireless Security System | Installation and Programming Guide CONTROL PANEL AND POWER SUPPLY MOUNTING After all the wiring complete, follow these steps to power up the Control Panel: Place the bottom of the Control Panel over the lower lip of the backplate and flip the Control Panel upwards. Then push the Control Panel over the mounting bracket until it snaps into place. it with the retaining screw. Peel off the adhesive backing from the power supply retaining bracket and attach the bracket to the outlet with a wall plate screw. Figure 18 Connecting Battery and Closing Panel A Connect battery B Align mounting plate inside of console bottom edge C Swing console up and snap into the mounting plate D Secure console with screw in retaining hole Spread the retaining bracket ears and plug the Control Panel’s power supply into the unswitched wall outlet. Slots are provided on the bracket to secure the power supply with a zip‐tie. After about five (5) seconds, the Control Panel indicates that power has been applied. If the Control Panel does not power up, check the power supply polarity. Figure 19 Securing the Power Supply 1 Place the screw here for a bracket on a standard style outlet. 2 Place the screw here for a bracket on a decora style outlet. NOTE: In the United States (and other countries where it is required), use the power supply retaining bracket. In Canada, ...
Page 25: Commercial Installations
COMMERCIAL INSTALLATIONS For commercial installations, the Control Panel is designed for use only as a burglary alarm system, and not for fire protection. Installation location and wiring methods shall be in accordance with ANSI/NFPA 70: National Electric Code, UL 681: Installation and Classification of Burglar and Holdup Alarm Systems, and UL 827: Central‐Station Alarm Services. NOTE: All entries and exits within a commercial installation setup must be protected according to the criteria provided by UL 681: Installation and Classification of Burglar and Holdup Alarm Systems. Figure 20 Commercial Installations Copyright © 2014 Linear LLC...
Page 26: Nfpa Standard 72
NFPA STANDARD 72 Smoke detectors must be installed in accordance with National Fire Protection Association (NFPA) Standard 72: National Fire Alarm and Signaling Code, which reads as follows: “2‐1.1.1 Smoke alarms shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit including basements and excluding crawl spaces and unfinished attics. In new construction, a smoke alarm shall be installed in each sleeping room. 2‐1.1.2 For family living units with one or more split levels (i.e., adjacent levels with less than one full story separation between levels), a smoke alarm shall suffice for an adjacent lower level, including basements. (Exception: Where there is an intervening door between one level and the adjacent lower level, a smoke alarm shall be installed on the lower level.) • Ceiling mounted smoke alarms should be located in the center of the room or hall, or not less than 4 inches from any wall. When the alarm is mounted on a wall, the top of the alarm should be 4 to 12 inches from the ceiling. • Do not install smoke alarms where normal ambient temperatures are above 100°F (37.8°C), or below 40°F (4°C). Also, do not locate alarm in front of air conditioners, heating registers, or other locations where normal air circulation will keep smoke from entering the detector. A‐2.5.2.1 Smoke Detection ‐ Are More Smoke Alarms Desirable? The required number of smoke alarms might not provide reliable early warning protection for those areas separated by a door from the areas protected by the required smoke alarms. For this reason, it is recommended that the residential user consider the use of additional smoke alarms for those areas for increased protection. The additional areas include the basement, bedrooms, dining room, furnace room, utility room, and hallways not protected by the required smoke alarms. The installation of smoke alarms in kitchens, attics (finished or unfinished), or garages is not normally recommended, as these locations occasionally experience conditions that can result in improper operation or false alarms.” NOTE: Smoke alarms are not to be used with detector guards unless the combination has been evaluated and found suitable for the purpose. Figure 21 Recommended Smoke Alarm Locations Copyright © 2014 Linear LLC...
Page 27: Home Screen
MAIN DISPLAY SCREENS For information about the Silent Control button, see the HOME SCREEN Control Panel’s User Guide. To go to the Home screen, press the Home button on the Control Panel. The Home screen reveals: ARMING SCREEN • System Status. The status of the system appears at the top left of the screen. For example, System The Arming screen lets users arm the security portion of Armed or System Ready, Not Armed. the system. It displays the system status and arming buttons for Stay and Away mode. It also includes these • Conditional Messages. A variety of conditional options: messages will also appear under the System Status. • Entry Delay Select this check box to arm the system • Time, Date and Weather. The current time, date, with an entry delay. Clear the check box to arm the and daily weather forecast (when the system system without an entry delay. See "(01) Exit/Entry 1" includes the GSM (Cellular) Radio Module and has on page 36 and "(02) Exit/Entry 2" on page 36. an active account with a Remote Services Provider) • Silent Exit Select this check box to silently arm the • System Status Icons. Icons in the top‐right corner system without sounding the exit delay beeps. Arming reveal a variety of conditions. See "System Status the system in Stay mode always uses silent exit. Icons" on page 29.
Page 28: System Status Screen
Go!Control Wireless Security System | Installation and Programming Guide SYSTEM STATUS SCREEN The System Status screen lists system status and any alerts. The date and time of alerts are listed in the displayed log. One option button for Silence is displayed; it temporarily stops the announcement of the system status during the status display. Figure 26 System Status Screen Copyright © 2014 Linear LLC...
Page 29: Toolbox Screens
TOOLBOX AND INSTALLER TOOLBOX The Control Panel includes two (2) different toolboxes for Figure 28 Toolbox (1 of 3) programming the system: • User Toolbox. Individuals with a user code can access basic programming functions. The user toolbox is simply called, the Toolbox. • Installer Toolbox. Individuals with the installer code can access both the basic programming functions of the user Toolbox and the more advanced programming functions of the Installer Toolbox. TOOLBOX SCREENS The Toolbox provides individuals who posses a user code Figure 29 Toolbox (2 of 3) with the ability to access basic programming functions. Accessing the Toolbox To access the basic Toolbox screens: At the Home screen, press Security, then Menu, and then Toolbox. At the Enter Your Code to Access the Toolbox screen, enter a user code. The default user code is 1111. Figure 27 Enter Your Code Screen Figure 30 Toolbox (3 of 3) When the Toolbox (1 of 3) screen appears, press the ...
Page 30: Accessing The System Configuration For System And Sensor Programming
Go!Control Wireless Security System | Installation and Programming Guide Accessing the System Configuration for System and Sensor Programming To access the system configuration screens for programming sensors into the system: Disarm the system by pressing Disarm and entering a user code. The default user code is 1111. Access the Installer Toolbox. See Accessing the Installer Toolbox above. At the Installer Toolbox screen, press the System Configuration button. NOTE: The other buttons let you restore the default Control Panel settings and provides access to a variety of system tests. Figure 31 Installer Toolbox Screen After pressing the System Configuration button, the first programming question appears. To learn more, see System Configuration Screens. SYSTEM CONFIGURATION SCREENS Use the System Configuration screens to program sensors into the system. Installers can access the System Configuration screens as described in Accessing the System Configuration for System and Sensor Programming. The System Configuration screens present installers with a sequential list of programming questions. For a list of all available programming questions, see "Programming Question Table" on page 33.
Page 31: Ac Power On/Off
SYSTEM STATUS ICONS The top line of the Control Panel’s display is the status bar TEST MODE that shows the current system mode, the status of the Figure 39 Test Mode sensors, and any current system trouble alerts. Special icons are displayed on the right side to provide visual This icon displays when the system is in Walk indications of the system’s current condition. Test mode. Figure 33 System Status Icons TOUCH SCREEN KEYPAD TRAFFIC Figure 40 Touch Screen Keypad Traffic An up arrow indicates the panel is sending information to the touch screen keypad (if installed). A down arrow indicates the touch screen keypad is sending information to panel. CELL RADIO Figure 41 Cell Radio If the option GSM (Cellular) Radio Module is ...
Page 32: Navigation Arrows & Go To Button
PROGRAMMING NAVIGATION When the installer is using the System Configuration QUESTIONS WITH SUB-OPTIONS menus, the Control Panel will present each programming Some of the programming questions have sub‐options. question sequentially. Most programming questions have a They navigate as follows. Questions with sub‐options single numeric value response or a simple enabled/ display a Skip button during the question. The Skip button disabled selection. Some programming questions have sub‐ advances to the next programming question/section. options that can be set. These sub‐options are displayed • The ↑ and ↓ arrows select the next or previous for the question selected and can be accessed through programming sub‐question. navigation keys on the display. • The ← and → arrows choose values for the ques on or move the cursor left and right along the white data NAVIGATION ARROWS & GO TO BUTTON entry field. The programming question screens display up, down, left, Figure 45 Questions with Sub-options and right navigation arrows. Use these arrows to scroll through the programming questions and to select sub‐ options. Press the Go To button and then enter a two (2)‐digit code ...
Page 33: Questions With Data Entry
Programming Navigation QUESTIONS WITH DATA ENTRY ADDITIONAL BUTTONS Some of the programming questions require entering Depending on the programming question, additional numeric or alphabetic data. For devices that can be named, buttons may be displayed on screen: the Control Panel contains a large vocabulary with words to • The Esc (Escape) button serves as an “undo”. choose from. See "Voice Descriptors" on page 38. Pressing Esc restores the value that was previously • The Insert button displays a word from the stored for the question or sub‐question. vocabulary. Use the ← and → arrows to scroll • The Sum (Summary) button displays a summary of through the word list, or enter the corresponding the values stored for the programming question and three (3)‐digit code. See "Voice Descriptors" on page sub‐options. 38. • The End button displays a summary of the values • The Backspace button moves the cursor to the left, stored for the entire Control Panel memory. deleting one (1) character at a time. • The Learn button is used to set the system to • The Delete button deletes a character to the right receive a sensor’s serial number during of the cursor, or any characters that are highlighted. programming.
Page 34: Ansi/Sia Cp-01 Compliance
PROGRAMMING OUTLINE Each system installed will require programming. Most After completing all setup and programming tasks, refer to installations being performed by the professional alarm the Control Panel’s User Guide for information about installer for a specific organization will have common operating the system. Check off the programmed options values set in every Control Panel that is reporting to the for the system in the User Guide. Central Station. Other programming values, such as the NOTE: Instruct the end user about proper system account number and sensor setup, may be unique for each operations, and leave the User Guide at the installation installation. site for reference. Use the following outline to guide you through the installation process. Understanding the Control Panel’s ANSI/SIA CP-01 COMPLIANCE programming structure will help to save time during each Several programmable options have the defaults pre‐set to installation. provide compliance with the American National Standards At this stage the following should be already completed: Institutes/Security Industry Association CP‐01 Control Panel • All wired sensors installed Standard. The table below details the settings that comply with ANSI/SIA CP‐01 and permanently programmed into • All wireless sensors installed the Console. The ANSI/SIA CP‐01 settings documented in • Control Panel mounted, connected, and powered the table below cannot be changed: Programming Ques‐ ANSI/SIA CP‐01 Range At the Home screen, press the system logo in the lower ...
Page 35: Programming Question Table
PROGRAMMING QUESTION TABLE Question Default Select RF Sensor # (01 to 48) Select RF Sensor # Type (00) Unused Select RF Sensor # Equipment Type Varies by RF sensor type Only shown for some sensor types Select RF Sensor # Equipment Code (0000) Other Enter RF Sensor # Other Equipment Code (0‐9999) NOTE: Only shown if (0000) Other is selected as the RF Sensor # Equipment Code Enter RF Sensor # Serial Number (7 digits) 0000000 Select RF Sensor # Equipment Age (0 to 1) (0) New Select RF Sensor # Loop Number (1 to 3) Varies with sensor model selected Select RF Sensor # Dialer Delay (0 to 1) (1) Enabled‡ (2) Disabled (for Fire and CO only) Construct RF Sensor # Voice Descriptor No Default Setting Select RF Sensor # Reports (0 to 1) (1) Enabled Select RF Sensor # Supervised (0 to 1) (1) Enabled Select RF Sensor # Chime (0 to 13) (0) Disabled Select Wired Sensor # (1 to 2) Select Wired Sensor # Type (00) Unused Select Wired Sensor # Equipment Age (0 to 1) (0) New Select Wired Sensor # Normal State (0 to 3) (0) Not Used Select Wired Sensor # Dialer Delay (0 to 1) (1) Enabled‡...
Page 36 Go!Control Wireless Security System | Installation and Programming Guide Question Default Select Emergency Key (0 to 1) (1) Audible Select Quick Arming (0 to 1) (1) Enabled Select Swinger Shutdown Count (1 to 6) (2) Two Trips‡ Select Siren Supervision Time (0 to 3) (0) Disabled Enter CS Lack of Usage Notification Time, in Days (0‐255) 7 Days Enter Radio Modem Network Failure Time (0‐255) 30 Minutes Select Radio Network Failure Causes Trouble (0 to 1) (1) Enabled Select Radio Modem Network Failure Reports (0 to 1) (1) Enabled Select Auto Stay (0 to 1) (1) Enabled‡ Select Exit Delay Restart (0 to 1) (1) Enabled‡ Select Quick Exit (0 to 1) (1) Enabled Enter Periodic Test, in Days (0‐255) 30 Days Enter Cancel Time, in Minutes (5‐255) 5 Minutes‡ Select Cancel Display (0 to 1) (1) Enabled‡ Select Cross Sensor 47‐48 (0 to 1) (0) Disabled Enter Cross Sensor Timeout, in Seconds (10‐120) 10 Seconds Select Abort Window Dialer Delay (0 to 2) (1) 30 Seconds‡ Select Burglary Bell Cutoff (0 to 4) (0) 4 Minutes Select Fire Bell Cutoff (0 to 4) (0) 4 Minutes Enter Time to Detect AC Loss, in Minutes (1‐30) 10 Minutes...
Page 37 Programming Question Table Question Default Select Z‐Wave Door Locks Feature (0 to 1) (0) Disabled Select Temperature Display Units (0 to 1) (0) Degrees Fahrenheit Select Services Require Master Code (0) Disabled Select Master User Access to Z‐Wave Toolbox (0 to 1) (0) Disabled Select Disable Siren After Two‐Way Audio (0 to 1) (0) Disabled Select Keyfob/Remote Arming Mode on System Not Ready (0 (0) Auto‐Bypass with Zone Participation on Restore to 2) Select Z‐Wave Siren Mode (0 to 1) (0) Sound for Burglary and Fire/CO Select Allow Backlight Always On (Demo Mode) (0) Disabled Select Energy Feature (0 to 2) (0) Disabled and Hidden Select Radio Modem Supplier Varies by Supplier Select Network Device (0 to 1) (0) none Network Device ID (Read‐Only) NOTE: Only appears if (1) Go!Bridge is selected in Q92 Select Network Device (0 to 1) Select Port # (1 to 8) (1) Port 1 NOTE: Typically, you will skip this question unless additional programming is required. Select Used (0 to 1) (0) Disabled NOTE: Typically, you will skip this question unless additional programming is required. Enter Port Value (0‐65535) NOTE: Only appears if (1) Enabled is selected in Select Used (0 to ...
Page 38: Sensor Types (Zones)
SENSOR TYPES (ZONES) Each sensor (wireless or wired) installed in the system is (05) Day Zone programmed to a specific sensor number and sensor type This sensor type is the same as a perimeter zone, except (zone). when the system is disarmed, a violation displays a trouble alert on the Console’s display. Common uses for this sensor The sensor number identifies the specific sensor when it is type are protection of sensitive areas that require displayed on the Control Panel, recorded in the event log, notification and possibly a Central Station trouble report, or reported to the Central Station. This allows pin‐point but not an alarm when the system is disarmed. information about any sensor in the system. The sensor type determines how and when the Control (06) 24-Hour Silent Alarm Panel responds to signals from the sensor. Some sensors This sensor type is active independent of the system are armed all the time, others are armed only in certain arming status. The code for silent panic is sent to the arming levels, some cause Central Station Reports anytime Central Station, but for safety, there are no visual or they are activated. The sensor’s type, along with other audible indications locally that this sensor type has been programming options, determine this. triggered. (00) Unused This is the setting for unused sensor numbers that do not (07) 24-Hour Audible Alarm have a sensor programmed into them. No system action ...
Page 39 Sensor Types (Zones) (16) 24-Hour Fire with Veriﬁcation † This sensor type is continuously armed 24‐hours a day. A sensor programmed to this type can trigger the local alarm fire sounder and the bell output regardless of the mode the system is in. Typical use would be for wireless smoke detectors. This sensor type is always active and cannot be bypassed. For verification, this sensor type must be violated twice in two (2) minutes, or remain violated for 30 seconds. If any other fire sensor (verified sensor type or not) violates within two minutes, both sensors will cause a fire alarm. (23) No Response Type This sensor type is a special zone that can be monitored for activity or inactivity by the Central Station. It does not affect security system status. (24) Silent Burglary This sensor type is for silent triggering the burglary alarm with perimeter doors and windows that will not be used to enter or exit the protected premises while the system is armed. The Control Panel’s sounder and the bell output will not activate. An instant silent alarm will occur when this type of sensor is triggered with the system armed in either the Stay or Away mode. † Indicates Sensor types that are not allowed for hardwire loops. Copyright © 2014 Linear LLC...
Page 40: Voice Descriptors
VOICE DESCRIPTORS The Control Panel includes a system vocabulary. When Code Word Code Word programming sensors when using firmware version 1.12, 062 EIGHT 130 LIGHT you can use the codes detailed in this table: 063 EIGHTEEN 131 LIGHTS 064 EIGHTY 132 LIQUOR Figure 49 List of Voice Descriptors 065 ELECTRIC 133 LIVING Code Word Code Word 066 ELEVEN 134 LOADING 002 ABORT 070 ENTRY 067 EMERGENCY 136 LOCK...
Page 41 Voice Descriptors Code Word Code Word 194 SET 262 SERVICE 195 SEVEN 263 SUNROOM 196 SEVENTEEN 264 WAREHOUSE 197 SEVENTY 265 GATE 198 SHED 266 APARTMENT 199 SHOP 267 FOYER 200 SIDE 268 TV 201 SILENT 269 VIDEO 202 SIREN 270 PORCH 203 SIX 271 CORNER...
Page 42: Equipment Codes
EQUIPMENT CODES The table below details the available equipment codes in firmware version 1.12. Code Equipment (0000) Other (0862) DW10‐345Thin Door/Window Contact (0863) DW20R‐345 Recessed Door Contact (0869) PIR1‐345 PIR with Pet Immunity (0864) GB1‐345 Glass break detector (0895) SMTK2‐345 GE Smoke/Heat detector (USA/Canada) (1058) SMTK3‐345 2GIG Smoke Detector (0872) SMKE1‐345 Smoke Detector (USA) (0871) SMKE1‐345C Smoke Detector (Canada) (0868) PANIC1‐345 Panic Button Remote (0860) CO1‐345 CO Detector (USA) (0859) CO1‐345 CO Detector (Canada) (1026) CO3‐345 2GIG CO Detector (USA/Canada) (0873) TAKE‐345 Takeover Module (0637) HWD/W”5816” (0470) HW R‐D/W “5818MNL” (0533) HW PIR “5890” (0530) HW PIR “5894Pi”...
Page 43: Account Registration
INSTALLER PROGRAMMING • Q: Select RF Sensor # Supervised. Control Panel ACCOUNT REGISTRATION checks for status reports from the sensor, or does The account registration process is used to enroll the not check for status reports] Control Panel with remote service provider’s Central Station. • Q: RF Sensor # Chime. Select voice announcement and chime options for the sensor. Typically, the account registration data is created with the service installation contract and then stored in a database Q1: RF Sensor Programming Outline managed by the Central Station. The data includes items such as the customer name, address, and the Central Figure 50 RF Sensor Programming Outline Station telephone number and account number assigned to the Control Panel. If you will be installing the 2GIG Go!Bridge IP Communicator, additional registration information required. For details, see the Installation Instructions included with the Go!Bridge IP Communicator. WIRELESS (RF) SENSOR PROGRAMMING The Control Panel can be programmed with up to 48 RF sensors of different types. In addition to the 48 multi‐...
Page 44: Summary Of Rf Sensor # Screen
Go!Control Wireless Security System | Installation and Programming Guide Scroll between op ons using the ← and → arrows. Move to RF Sensor Programming Questions the previous or next prompt by pressing the ↑ and ↓ arrows. Q1: Select RF Sensor # (01-48) Up to 48 wireless RF sensors can be used with each Control To program another sensor click Next. Panel. The options for each sensor are programmed with To exit programming, click Skip then End and Exit. Upon sub‐option questions. exit, the panel takes several seconds to restart. Enter the RF sensor number or press the ← or → arrows *Only used for “other” equipment to select it. **Press Insert for each word. To select from the list, you Program the sensor details by using the ↑ and ↓ can use the keypad or press the ← or → arrows. arrows to select each of the sub‐options. Summary of RF Sensor # Screen NOTE: To skip Q1 and jump directly to Q2 for Wired Sensor Programming, press Skip. After setting all the options for a sensor, the RF sensor summary screen is displayed. The screen can also be displayed for programmed sensors during RF sensor Q: Select RF Sensor # Type program editing by pressing the Sum button.
Page 45 Installer Programming Q: Select RF Sensor # Equipment Type Q: Enter RF Sensor # Serial Number (7 Digits) DEFAULT: Varies by RF Sensor Type DEFAULT: 0000000 RF sensor serial numbers can be manually entered or NOTE: Some sensor types (zones) will require you to specify automatically transmitted from the sensor to the Control an equipment type selection, which affects the sensor’s Panel. extended reporting code. • For manual entry. Enter the sensor number that Simply enter the appropriate equipment type code (see was logged for the sensor being programmed. Press table below) or press the ← or → arrows to select the Shift to access alphabetic characters. appropriate equipment type. • For automatic entry. Press Shift, then press Learn The table below shows the Equipment Types available for to place the Control Panel into learning mode. Then each Sensor Type (Zone): trigger the RF sensor. The Control Panel will beep Sensor Type (Zone) Equipment Types four (4) times and learn the sensor’s serial number.
Page 46 Go!Control Wireless Security System | Installation and Programming Guide Q: Select RF Sensor # Loop Number (1 to 3) Q: Select RF Sensor # Reports (0 to 1) DEFAULT: Varies with sensor model selected DEFAULT: (1) Enabled The 2GIG Door/Window Contact sensors have two (2) RF sensors can be programmed to trigger a report to the inputs: an internal magnetic contact and an external Central Station or not. Normally Closed (N/C) hardwire input. Either or both sensor • The default setting (1) Enabled enables reporting inputs can be used. for this RF sensor number. TIP: Some sensors are capable of three (3) loop inputs. • To prevent reporting for this RF sensor number, select (0) Disabled. NOTE: When using both the internal magnetic contact and the external input, the magnet contact AND the Q: Select RF Sensor # Supervised (0 to 1) external contact must be assigned a different RF sensor ...
Page 47: Wired Sensor Programming
Installer Programming WIRED SENSOR PROGRAMMING Q2: Wired Sensor Programming Outline The Control Panel can be programmed with up to two (2) Figure 52 Wired Sensor Programming Outline wired sensors. The wired sensors are hardwire contact loops connected to the loop input terminals on the Control Panel’s terminal strip. To see where the two (2) hardwire sensors can be wired into the Terminal Block, see the "Terminal Block Wiring Diagram" on page 20. CAUTION: Wired sensors cannot be used for a CO or Fire sensor loop. IMPORTANT: Note that Wired Sensor reports as below: • Wired Sensor #1 = Reports as Sensor #49 • Wired Sensor #2 = Reports as Sensor #50 See Figure 52 "Wired Sensor Programming Outline" on page 45 on the next page for the steps required to program wired sensors into the Control Panel. The options that can be set for each wired sensor are: • Q2: Wired Sensor Number. Select 1 or 2. • Q: Wired Sensor # Type. Select the zone. For example, (01) Exit/Entry 1, (02) Exit/Entry 2, (03) Perimeter, and so on. See "Sensor Types ...
Page 48: Summary Of Wired Sensor # Screen
Go!Control Wireless Security System | Installation and Programming Guide Summary of Wired Sensor # Screen Sensor Types (Zones) RF Wired Sensors Sensors After setting all the options for a sensor, the wired sensor summary screen is displayed. The screen can also be (07) 24‐Hour Audible Alarm displayed for programmed sensors during wired sensor (08) 24‐Hour Auxiliary Alarm program editing by pressing the Sum button. (09) 24‐Hour Fire (10) Interior with Delay • While programming each wired sensor remember (14) 24‐Hour Carbon Monoxide that the ← and → arrow bu ons step through each of the wired sensor numbers. • To return to programming, click the Edit Current or Q: Select Wired Sensor# Equipment Type Edit Next buttons. DEFAULT: Varies by wired sensor type • Pressing Skip goes to question number Q3 (RF Key This question is only displayed when certain sensor types Fob Programming). See "Wireless (RF) Key Fob are selected.
Page 49: Q: Select Wired Sensor# Dialer Delay (0 To 1)
Installer Programming Q: Select Wired Sensor# Normal State Q: Select Wired Sensor# Chime (00 to 13) DEFAULT: (0) Not Used DEFAULT: (0) Disabled The two hardwire loops can be wired for normally open (N/ Each wired sensor can be set to sound a “ding‐dong” chime O) or normally closed (N/C) contacts, or for end‐of‐line and/or sound its (EOL) resistor. voice descriptor when the sensor is triggered. • The default setting (0) Not Used disables this wired • The default setting (0) Disabled inactivates the sensor. chime for this wired sensor. • To use this wired sensor, select the way the loop is • If a chime and/or voice is required for this wired wired: sensor, choose one of the other chime options: Wired Sensor Normal State Sensor Chime • (0) Not Used Code Sensor Chime •...
Page 50: Wireless (Rf) Key Fob Programming
Go!Control Wireless Security System | Installation and Programming Guide WIRELESS (RF) KEY FOB Key Fob Programming Outline PROGRAMMING Figure 54 Key Fob Programming Outline The Control Panel can be programmed with up to eight (8) RF key fobs. Programming the fobs into the Control Panel involves selecting the sensor number for a particular device, setting or learning the serial number, and selecting the other options for the sensor. IMPORTANT: RF key fobs 1 ‐ 8 report to the Control Panel as sensors 51 ‐ 58 (opening/closing, emergency, and low battery reports). Fob # Reports as Sensor # 4 See Figure 54 Key Fob Programming Outline for the steps required to program fobs into the Control Panel. The options that can be set for each fob are: • Q3: Select Fob Number. Select key fob number 1‐8. • Q: Select Fob # Used. Select (0) Disabled or (1) Enabled. • Q: Select Fob # Equipment Code. Select the four (4)‐digit equipment code that corresponds to the appropriate keyfob. See "Equipment Codes" on ...
Page 51: Summary Of Rf Key Fob # Screen
Installer Programming Summary of RF Key Fob # Screen Q: Enter Fob # Serial Number(7 Digits) DEFAULT: 0000000 After setting all the options for a key fob, the Summary of Fob # screen is displayed. The screen can also be displayed Key fob serial numbers can be manually entered or learned for programmed sensors during wired sensor program from the fob. editing by pressing the Sum button. • For manual entry, enter the fob number that was logged • While programming each key fob remember that the ← for the fob being programmed. Use the Shift button to and → arrow bu ons step through each of the key fob access alpha characters. numbers. • For automatic entry, press Shift, then press Learn. The • To return to programming, click the Edit Current or Edit Control Panel will wait for a fob transmission. Trigger Next buttons. the fob being programmed and the Control Panel will • Pressing Skip goes to question number Q4 (RF Keypad ...
Page 52: Q: Select Fob (#) Arm No Delay (0 To 1)
Go!Control Wireless Security System | Installation and Programming Guide Q: Select Fob (#) Arm No Delay (0 to 1) DEFAULT: (0) Disabled Key fobs can be set to arm the Control Panel with or without an entry delay. • The default setting (0) Disabled sets this fob to arm the system with an entry delay. • To set this fob to arm the system without an entry delay, select (1) Enabled. Q: Select Fob# Key 4 Output (0-2) DEFAULT: (0) Disabled The key fob’s auxiliary button can be used to trigger the Control Panel’s open collector output. The default setting (0) Disabled deactivates the fob’s auxiliary button. To use this fob’s auxiliary button, select the output function: • (0) Disabled • (1) Toggle Output • (2) Momentary Output Copyright © 2014 Linear LLC...
Page 53: Wireless (Rf) Keypad Programming
Installer Programming WIRELESS (RF) KEYPAD PROGRAMMING RF Keypad Programming Outline The Control Panel can be programmed with up to four (4) Figure 55 Keypad Programming Outline RF keypads or RF touch screen keypads. NOTE: RF Keypads 1 ‐ 4 report to the Control Panel as sensors 59 ‐ 62 (for emergency, and low battery reports) RF Keypad Reporting Codes Keypad 1 Reports as sensor #59 Keypad 2 Reports as sensor #60 Keypad 3 Reports as sensor #61 Keypad 4 Reports as sensor #62 • User Codes #1 ‐ #8 are reported for openings and closings • User Code #0 is reported for Quick Arming The following options can be set for each RF keypad: • Select RF Keypad Number. Select keypad number 1‐4. • Select RF Keypad # Used. Enable or disable the keypad. ...
Page 54: Summary Of Rf Keypad Screen
Go!Control Wireless Security System | Installation and Programming Guide Summary of RF Keypad Screen Q: Enter RF Keypad# Serial Number (7 Digits) DEFAULT: 0000000 After setting all the options for a sensor, the RF keypad summary screen is displayed. The screen can also be displayed for programmed RF keypads by pressing the Sum RF Keypad (#) Keypad ID (read‐only) button. Serial numbers for standard wireless keypads can be • To return to programming, click the Edit Current or manually entered or learned from the keypad. For Wireless Edit Next buttons. Touch Screen Keypads, serial numbers can only be learned • Pressing Skip goes to question Q5 (Control Panel from the keypad. Read‐only with Keypad ID’s refer to the programming). installer being unable to manually input an id. • To exit programming, click Skip then End and Exit. Standard Keypads: Upon exit, the Control Panel takes several seconds • For manual entry, enter the Wireless Keypad that to restart. was logged for the keypad being programmed. Press the Shift button to access alpha characters. RF Keypad Programming Questions •...
Page 55 Installer Programming Q: Select RF Keypad# Emergency Keys (0 to 1) DEFAULT: (1) Enabled NOTE: This step is not displayed for Wireless Touch Screen keypads. Standard wireless keypads have 24‐hour emergency buttons labeled Fire and Police. • The default (1) enables this RF Keypad’s emergency keys. • To disable this RF Keypad’s emergency keys, select disabled (0), the keys will not be able to trigger an alarm or report. NOTE: The RF Keypad’s POLICE button triggers a silent alarm if programming question Q16: Police Emergency Key (0‐2) is set to (2) Silent Panic. IMPORTANT: To ensure that a signal is sent, instruct the end user to press and hold down the emergency key on the keypad until its indicator light illuminates. Q: Construct RF Keypad# Voice Descriptor DEFAULT: (#) Keypad The voice descriptor is the words the Control Panel will announce for this RF Keypad. Up to five words are allowed.
Page 56: Programming Questions
CONTROL PANEL PROGRAMMING PROGRAMMING QUESTIONS • The default setting of 45 sets the timer to 45 seconds. Q1: RF Sensor Programming • To change the timer setting, enter a value between 30‐240 seconds. To learn about RF sensor programming, see "Wireless (RF) Sensor Programming" on page 41 Q8: Dialer (0-1) Q2: Wired Sensor Programming DEFAULT: (0) Disabled To learn about wired sensor programming, see "Wired The dialer (digital communicator) can be enabled for a Sensor Programming" on page 45 monitored system or disabled for a local alarm or when the GSM (Cellular) Radio Module is used exclusively for reporting. Q3: RF Key Fob Programming • The default setting (0) Disabled turns the dialer To learn about RF key fob programming, see "Wireless (RF) OFF. Key Fob Programming" on page 48.
Page 57: Q11: Cs #1 Phone Number (0‐25 Digits)
Control Panel Programming Q11: CS #1 Phone Number (0-25 Digits) • Press 2 to enable VOX mode two (2)‐way communications from the Central Station to the DEFAULT: No Default premises. Enter the telephone number for the Central Station #1. You • Press 3 to enable Listen mode one (1)‐way can enter up to 25 digits. communication from the premises to the Central • Enter the Central Station #1 telephone number. Station. • Access the pound and star symbols by pressing the • Press 7 to extend the session five (5) minutes Shift button. The P button adds a three (3)‐second without changing the mode of operation. pause to the dialing. • Press 9 to end the audio session an terminate the NOTE: If a second Central Station telephone number is call. programmed with question Q41: CS #2 Account Number, the Control Panel alternates between the two Central Q14: Silent Panic/Burglary Listen Only Station telephone numbers. After two failed telephone ...
Page 58: Q18: Emergency Key (0‐1)
Go!Control Wireless Security System | Installation and Programming Guide Q18: Emergency Key (0-1) Q22: CS Lack of Usage Notification Time DEFAULT: (1) Audible (0-255) The Control Panel’s emergency button can be enabled or DEFAULT: (7) Seven Days disabled. The panel’s emergency button is displayed by If this system has not been armed for a specified number of pressing the Emergency button on the panel. days, inactivity reports can be sent to the Central Station. • The default setting (1) Audible sounds an audible • The default setting is (7) Seven Days. alarm when the button is pressed. • To change the duration, select a value between 1 to • To disable this button, select (0) Disabled. 255 days. NOTE: If all three (3) Emergency buttons are disabled, the • To turn this feature OFF, select (0) Disabled. Control Panel displays a message when its Emergency button is pressed. Q23: Radio Modem Network Failure Time (0-255) Q19: Quick Arming (0-1) DEFAULT: 30 Minutes...
Page 59: Q26: Auto Stay (0‐1)
Control Panel Programming Q26: Auto Stay (0-1) Q31: Cancel Time, in Minutes (5-255) DEFAULT: (1) Enabled DEFAULT: 5 minutes This feature must be enabled for ANSI/SIA CP‐01 compliance The minimum setting for ANSI/SIA CP‐01 compliance is 5 minutes. The number of minutes can be increased without When auto stay is enabled and the system is armed in the affecting ANSI/SIA CP‐01 compliance. Away mode, if an exit/ entry sensor is not violated during the Exit Delay, the system will arm in the Stay mode. A cancel report will be sent to the Central Station after an alarm, if the system is disarmed within the programmed • The default setting is (1) Enabled which turns the time. auto‐stay feature ON. • The default setting for the cancellation time is five (5) • To turn this feature off, select (0) Disabled. minutes. NOTE: If the system is remotely armed in Away mode using • To extend this time interval, enter a value between six a key fob, telephone, mobile app, or computer, the (6) to 254 minutes. auto‐stay feature will not switch the system to Stay •...
Page 60: Q34: Cross Sensor Timeout, In Seconds (10‐120)
Go!Control Wireless Security System | Installation and Programming Guide Q34: Cross Sensor Timeout, in Seconds Q37: Fire Bell Cutoff (0-4) DEFAULT: (0) 4 Minutes (10-120) DEFAULT: 10 Seconds When a fire alarm is triggered, the bell sounds until the fire bell cutoff time expires. The cross sensor timeout is the maximum period of time allowed between violation of sensors 47 and 48 that will • The default setting (0) 4 Minutes sets the burglary trigger an alarm. If both sensors are violated within this bell cutoff to four (4) minutes. time period, an alarm will be triggered. If both sensors are • To change the fire bell cutoff time, select an option not violated within this time period, an alarm will not be below triggered. Fire Bell Cutoff Time NOTE: Cross sensor verification must be enabled with (0) 4 minutes Q33: Cross Sensor 47‐48 for this feature to function. (1) 8 minutes (2) 12 minutes • The default setting for the cross sensor timeout is (3) 16 minutes 10 seconds. (4) Unlimited •...
Page 61: Q39: Random Ac Loss Report Time (0‐1)
Control Panel Programming Q39: Random AC Loss Report Time (0-1) When the panel answers the phone, the user will be prompted to enter their code. If a valid code is entered, the DEFAULT: (1) Enabled system will announce the current system status. If an invalid This feature allows the system to report AC power loss and code is entered, the panel will ask for the code again. After AC power restore at a random time of up to 45 minutes two invalid attempts, the panel will disconnect. After two after the event occurs. This helps to reduce Central Station calls, with two invalid attempts each, the panel will lock out. congestion due to a wide‐spread power outage affecting The lock out will last for 30 minutes. many Control Panels at once. The random AC power status • The default setting is (3) Data and Voice. report timer is triggered based on the time set by Q38: • To use data access only, select (1) Data Only. Random AC Loss Report Time. • To use voice access only, select (2) Voice Only. • The default setting (1) Enabled turns this feature ON. • To turn the remote access feature OFF, select (0) Disabled. • To turn this feature OFF, select (0) Disabled. Telephone Remote Control Phone ...
Page 62: Q43: Installer Code (4 Digits)
Go!Control Wireless Security System | Installation and Programming Guide Q43: Installer Code (4 Digits) fields, select (1) Default All Except CSID, Account/ Phone, Lockouts. DEFAULT: 1561 • To deny hard and soft resetting of the Control The installer code is a unique code that installation Panel, select (2) Default None. technicians use to access the Installer Toolbox on the If option 1 or 2 is selected, the option takes effect after the Control Panel. system runs for 48 hours. This allows the installer to go back • The default installer code is 1561. and make changes if required. • To change the installer code, enter a new four (4)‐ digit code. Q46: Trouble Doesn’t Sound at Night (0- IMPORTANT: If you change the installer code, always write it down so you can access the system later. DEFAULT: (1) Enabled NOTE: The installer code must be unique from the master user code and all other user codes. NOTE: For UL 985: Household Fire Warning System Units installations, this setting must be set to (0) Disabled The Control Panel will sound trouble beeps caused by AC ...
Page 63: Q51: Manual Bypass Reports To Cs (0-1)
Control Panel Programming Q48: Download CSID (6 Digits) Q52: AC Loss Reports to CS (0-1) DEFAULT: 000000 DEFAULT: (1) Enabled The system supports a six (6)‐digit CSID code that is used for AC power loss reports can be sent to the Central Station if remote telephone programming of the Control Panel. This the Control Panel loses AC power. code is verified when the Control Panel connects with the • The default setting (1) Enabled allows AC power loss downloading software. If the CSID code doesn’t match the reports. downloading software, the Control Panel will deny the • To turn off AC power loss reports, select (0) connection. Disabled. • The CSID code can be entered manually with this NOTE: The AC power will have to be absent from the programming question. Control Panel for the time set by programming question • If this field is left with the default (000000), the first Q38 before the AC power loss trouble alert is ...
Page 64: Q57: Alarm Restore Reports To Cs (0-1)
Go!Control Wireless Security System | Installation and Programming Guide Q57: Alarm Restore Reports to CS (0-1) Q61: System Low Battery Restore DEFAULT: (0) Disabled Reports to CS (0-1) Alarm restore reports can be sent to the Central Station DEFAULT: (1) Enabled after an alarm when either the bell timeout has been When a low battery condition is restored on the Control reached or the system is disarmed. If alarm restores are Panel, the system can send a restore report to the Central enabled and swinger shutdown is set to two, a restore will Station. be reported if the sensor is closed (normal state) at bell • The default setting (1) Enabled allows the system to cutoff or becomes closed after bell cutoff. If swinger send reports when low battery conditions are shutdown is set to one, a restore will only be sent if the restored. sensor is closed at the time of disarm. Restores are not sent • To turn this feature OFF, select (0) Disabled. if a sensor is in swinger shutdown until the time of disarm and the sensor is closed. • The default setting (0) Disabled prevents alarm Q62: RF Low Battery Restore Reports to restore reports.
Page 65: Q65: Rf Jam Causes Trouble (0-1)
Control Panel Programming Q65: RF Jam Causes Trouble (0-1) Q71: System Tamper Causes Trouble (0- DEFAULT: (0) Disabled The system can monitor the Control Panel’s sensor receiver DEFAULT: (1) Enabled and detect whether a transmitter is stuck on the air causing A tamper switch on the Control Panel detects if the case has jamming. When jam detect is enabled, the Control Panel been opened. The system can be programmed so that a will indicate a trouble condition if RF jamming is detected. tamper switch activation will cause a trouble indication if the system is disarmed, and an alarm if the system is armed. NOTE: This programming question only functions if trouble reports are enabled with programming question Q50. • The default (1) allows the Control Panel tamper switch to trigger trouble when the system is • The default setting (0) Disabled turns RF jam disarmed, and alarm when the system is armed. detection OFF. • To have the system ignore the Control Panel tamper • To turn on RF jam detection, select (1) Enabled. switch, select (0) Disabled. Q66: Daylight Saving (0-1) Q72: Quick Bypass (0-1) DEFAULT: (1) Enabled...
Page 66: Q75: Auto Un Bypass For Manual Bypass (0-1)
Go!Control Wireless Security System | Installation and Programming Guide Q75: Auto Un Bypass for Manual Bypass Open Collector Output Mode (0-1) (03) Activated on FTC (Failure to Communicate) (04) Activated on Siren Supervision DEFAULT: (1) Enabled (05) Activated on Radio Fault Violated (open) sensors can be manually bypassed by the (06) Activated on Burglary Alarm user through the User Toolbox or force bypassed at the time (07) Activated on Fire Alarm of arming. (08) Activated on Any Alarm Force bypassed sensors automatically have their bypasses (09) Activated on Any System Trouble removed when the system is disarmed. (10) Z‐Wave activation (Option #10 not currently active) Manually bypassed sensors can have their bypass (11) Follows Internal Sounder Alarm automatically removed at disarming or have their bypasses (12) Follows Exit/Entry Beeps remain in place. • The default setting (1) Enabled automatically removes bypasses from manually bypassed sensors when the system is disarmed. Q79: Z-Wave Feature (0-3) • To have manually bypassed sensors remain DEFAULT: (1) Disabled but Visible bypassed when the system is disarmed, select (0) ...
Page 67: Q82: Z-Wave Door Locks Feature (0-1)
Control Panel Programming Q82: Z-Wave Door Locks Feature (0-1) NOTE: When (1) Enabled, the Installer code will still be required to access the Advanced Toolbox menu. This DEFAULT: (0) Disabled prevents end users from adding or removing Z‐Wave Display of the Home Service’s Door Locks button can be devices. enabled or disabled. This programming question only functions if the Z‐Wave feature enable question Q79: Z‐ Wave Feature is set to (2) or (3). Q86: Disable Siren After Two-Way Audio • The default setting (0) Disabled hides the Door (0-1) Locks button. DEFAULT: (0) Disabled • To display the Door Locks button, select (1) This setting enhances system operation in personal Enabled. emergency applications and also provides the dealer with the option of the siren sounding until the bell cut off or to the end of a two‐way‐voice session. Q83: Select Temperature Display Units •...
Page 68: Q90: Energy Feature (0 To 1)
Go!Control Wireless Security System | Installation and Programming Guide Q90: Energy Feature (0 to 1) Q93: Enter Broadband Network Failure DEFAULT: (0) Disabled and Hidden Time (1-255) Select (1) Disabled but Visible to show but not activate the DEFAULT: 30 Minutes energy features. You can also select (2) Enabled to turn the NOTE: The Go!Bridge IP Communicator must be installed to energy feature ON. use this function. Sets the amount of time required for triggering a trouble Q91: Radio Modem Supplier condition if the system detects that the broadband network has lost its connection. After the connection has been DEFAULT: (0) None restored, the trouble condition clears. NOTE: If you enable Q44: Select Lock Installer • The default failure detection setting is 30 minutes. Programming, you will not be able to change this setting. • To choose a different failure detection time, enter the number of minutes between 1‐255. Select the option that corresponds to the appropriate ...
Page 69: Final Installation Setup
Control Panel Programming FINAL INSTALLATION SETUP or not, or to have conditional validity. Refer to the User Guide for details on setting User Code Access Schedules. When done, press Back. Exiting Programming (System Press Brightness/Volume. Set the level for the display Configuration) brightness. Set the chime & voice volume. When done, After programming the Control Panel, all the changes need press OK. to be saved in memory. After saving, the programmed settings will remain in memory, even after a total power loss. After setting all the required programming values for the sensors and the Control Panel, press End. Review the Summary of System Configuration screen. Use the ↓ and ↑ arrows to scroll through the lis ng. Verify that each option is set correctly. To view the 2nd Toolbox screen, press →. To set the display lighting timeout, press Back Light Timeout. Choose the length of time that the display will remain lit after it is idle. When done, press OK. To set the calendar and the clock press Set Date and Set Time. To save the programming changes, be sure the Save Changes option is checked. To exit without saving programming changes un‐check the Save Changes option (for verification, an additional confirmation screen appears). Press Exit. The Control Panel takes a few seconds to restart and display the Home screen. Customizing the Installation After programming the Control Panel, go to the User ...
Page 70: Access The Installer Toolbox
INSTALLER TESTING When installation and programming is complete, use the Fire Test. Trigger a 24‐Hour fire sensor (if installed) or option in the Installer Toolbox to test for proper system press the Control Panel’s Emergency button and operations. then press the Fire button (if enabled). Wait for approximately 45 seconds for the report to complete, then disarm the console. ACCESS THE INSTALLER TOOLBOX Panic Test. Trigger a 24‐Hour Panic sensor (if installed) To access the Installer Toolbox: or press the Control Panel’s Emergency button and At the Home screen, press the logo in the lower‐right then press the Panic button (if enabled). Wait about 45 corner. seconds for the report to complete, then disarm the At the Enter a Code screen, enter the installer code console. (the default installer code is 1561). Emergency Test. Trigger a 24‐Hour emergency sensor The Installer Toolbox (1 of 3) screen appears. (if installed) or press the Emergency button (if enabled), wait about 45 seconds for the report to complete, then disarm the console. DISABLE/ENABLE STATUS When testing the Control Panel, both the internal and Burglary Test. Arm the system, then trigger a burglary external sounder (if installed) will be activated. To limit sensor, wait for the system to go into alarm mode, then noise during the testing process, the Control Panel offers wait about 45 seconds for the report to complete, and an option to disable the sounder. ...
Page 71: Performing A Walk Test
Installer Testing Performing a Walk Test RADIO STATUS TEST If the GSM (Cellular) Radio Module is installed in the To perform a Walk Test: Control Panel, use the Radio Status screen to view signal At the Installer Toolbox screen, press the Walk Test strength, serial number, registration status, and other button. information for the cellular connection. The is a helpful tool NOTE: For the 25 minutes that the system is in Walk Test to use when troubleshooting the installation. mode, the system beeps once every 30 seconds. During the last five (5) minutes, the system beeps two (2) times Cell Phone Test every 30 seconds. The icon also flashes in the status To perform a cell phone test: bar. At the Installer Toolbox screen, press the Radio Status Press the ↓ and ↑ arrows to scroll through the sensor button. list. In the Radio Status screen, press the Cell Phone Test Activate the first sensor in the list and review the result button. on the screen: • When a sensor is received by the Control Panel, three (3) beeps occur and the display lights a green bar to the left of the sensor’s name. •...
Page 72: Telephone Test
Go!Control Wireless Security System | Installation and Programming Guide Telephone Test IMPORTANT: This action does not restore factory default settings for Z‐Wave questions Q79‐Q83. Use this test to verify the land‐line connection from the panel’s built‐in digital communicator and Central Station. Hard Reset At the Toolbox (3 of 3) screen, press the Telephone Test A hard‐reset restores all of the programming settings back button. to the factory defaults. NOTE: Before performing a hard reset, Q44: Lock Installer Programming must be set to option (1) or (2) and Q45: Lock Default Programming must be set to (0). See "Q44: Lock Installer Programming (0‐2)" on page 60. To perform a hard reset: Remove the Control Panel cover and completely disconnect all power to the Control Panel. On the inside back of the Control Panel, plug in the backup battery. Press and hold down the Emergency and Home At the Enter Master Code to Access Telephone Test buttons. screen, enter the master code. Continue to hold down the Emergency and Home The top area of the Telephone Test screen shows the buttons and then connect DC Power to the Control Control Panel actions and the bottom area shows the Panel. results. Release the buttons only after both the Emergency Press the ↓ and ↑ arrows to review the ac ons and ...
Page 73: Wireless Product Notice
REGULATORY INFORMATION WIRELESS PRODUCT NOTICE Radio controls provide a reliable communications link and fill an important need in portable wireless signaling; however, there are some limitations which must be observed. • For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. • A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. • Changes or modifications to the device may void FCC compliance. • Infrequently used radio links should be tested regularly to protect against undetected interference or fault. • A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the end users. FCC NOTICE This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Relocate the Console away from the TV/radio receiver. • Plug the Console into a different wall outlet so that the Console is on a different branch circuit. • Re‐orient the TV/radio antenna. • If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. FCC Telephone Rules and Regulations The FCC requires that this alarm dialer system not make more than 15 repetitive dialing attempts to a single telephone ...
Page 74 Go!Control Wireless Security System | Installation and Programming Guide NOTE: The standard backup battery that is included with all 2GIG Control Panels does not support UL 985 installations. To comply with the secondary supply requirement in UL 985 Household Fire Warning System Units, you must install the 2GIG Console Battery Pack (2GIG‐BATT2X). IMPORTANT: All conductors and attachments are manufactured in accordance with the Standard for UL 681: Installation and Classification of Burglar and Holdup Alarm Systems. The Control Panel contains hard wiring that is protected and not exposed. All conductors and attachments are manufactured in accordance with the UL 681: Installation and Classification of Burglar and Holdup Alarm Systems. Stranded conductors clamped under wire‐binding screws or similar parts shall have the individual strands soldered together or arranged in a construction that has been determined to be the equivalent. IMPORTANT: A local alarm sounding device, alarm housing, and control unit shall comply with the mercantile requirements in UL 365: Police Station Connected Burglar Alarm Units and Systems. Copyright © 2014 Linear LLC...
Page 75: Limited Warranty
LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for one (1) year. This warranty extends only to wholesale customers who buy direct from Linear LLC or through Linear LLC’s normal distribution channels. Linear LLC does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other warranties expressed or implied. 2GIG by Linear 1950 Camino Vida Roble, Suite 150 Carlsbad, CA 92008 USA For technical support in the USA and Canada: 855‐2GIG‐TECH (855‐244‐4832) Email: 2gigtechsupport@linearcorp.com Visit web site for technical support hours of operation For technical support outside of the USA and Canada: Contact your regional distributor Visit dealer.2gig.com for a list of distributors in your region 77‐000063‐001 Rev. A Copyright © 2014 Linear LLC...
Page 77 THIS PAGE INTENTIONALLY LEFT BLANK...

2gig Technologies Go!Control Panel Installation & Programming Manual

External Features

Wireless System Sensors

Control Panel Mounting Plate

Home Screen

Installer Toolbox Screens

Low Backup Battery

Ansi/Sia Cp-01 Compliance

RF Sensor Programming Questions

Quick Links

Need help?

Questions and answers

Related Manuals for 2gig Technologies Go!Control Panel

Summary of Contents for 2gig Technologies Go!Control Panel

Table of Contents