Sanyo PLV-80 Service Manual page 40

Electrical Adjustments
Group No. Item
10 GAIN target
11 GAIN torelance
12 Auto Status
13 AutoWait
14 CHECK -Tolelance
681 AutoPC Adjsut
0 AutoPCAdjustEnable
1 Frequency Step
2 Frequency Threshold
3 Fine Phase
4 BLKDET
5 PHASEMSK
690 CUSTOM(Aspect)
0 Connect
1 Horizontal Scaler
2 Horizontal Position
3 RESET/STORE
4 Vertical Scaler
5 Vertical Position
6 RESET/STORE
7 Screen Select
8 CUSTOM ON/OFF
700 General
0 IP Mode
1 3:2 PullDown Mode
2 Detect Film Mode Enable
3 Force IP Mode
701 Deinterlacer setting
0 Motion Adaptive Weight Value
1 Angle Interpolation Level
2 CUE LOW Pass Filter Enable
702 Deinterlacer setting
0 Motion Adaptive Weight Value
1 Angle Interpolation Level
711 Noise Reduction (Time)
0 Noise Pixel Range
1 Noise Region 0
2 Noise Region 1
3 Noise Region 2
4 Noise Gain Level
713 Noise Reduction (Time)
0 Noise Pixel Range
1 Noise Region 0
2 Noise Region 1
3 Noise Region 2
4 Noise Gain Level
715 Noise Reduction (Time)
0 Noise Pixel Range
1 Noise Region 0
2 Noise Region 1
Function
White Level adj. Target Value
White Level Adj. Tolerance Range
Result of Auto Calibration (Maintain Last Adj.)
0: End correctly
1: On Calibration
9: End with Error
Wait value for each Settings
OFFSET Tolerance
0: AutoPCAdjust Enable 1:AutoPCAdjust Prohiit Normally
Frequency Step in TotalDot Search
Confirm TotalDot
0 [] <--- -----> 10 [No]
Executes Phase after Total Dot Adj.
0: Executes FinePhase1:Not Execute
Detection Area of Black Level
Phase Detection Filter 0:Effect All Bit 1: Disable lower 1 bit
2:Disable lower 2 bit 3:Disable lower 3 bit
Indivisual/Link Edition (0: Indivisual, 1: Link)
H-Scaler Edition
H-Position Correction
Reset of H-Aspect/Save (0: reset, 1: Save)
V-Scaler Edition
V-Position Correction
Reset of V-Aspect/Save (0: reset, 1: Save)
Screen Mode Selection (0:FULL 1:NORMAL)
Custom (0: Disable, 1: Enable)
Setting at IP OFF
0:Not used for IP Block
1:IP OFF with IP Block
bit0 : Global Motion
bit1 : Video Motion
0 : 2:3pull down & 2:2pull down
1 : 2:3pull down
2 : 2:2pull down
0 : IP Process Disable
1 : Force Normal IP Mode
2: Force Film Mode
Effective only for Progressive ON / Film
<KDEINT>
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
Effective only for Progressive ON - L2
<KDEINT>
0 : Conservative <====> 4 : Aggressive
Effective only for N.R L1
<NSRANGEY> / <NSRANGEUV>
<NSREGIONY0> / <NSREGIONUV0>
<NSREGIONY1> / <NSREGIONUV1>
<NSREGIONY2> / <NSREGIONUV2>
<NSFILTERY**> / <NSFILTERUV**>
Effective only for N.R L2
<NSRANGEY> / <NSRANGEUV>
<NSREGIONY0> / <NSREGIONUV0>
<NSREGIONY1> / <NSREGIONUV1>
<NSREGIONY2> / <NSREGIONUV2>
<NSFILTERY**> / <NSFILTERUV**>
Effective only for N.R OFF
<NSRANGEY> / <NSRANGEUV>
<NSREGIONY0> / <NSREGIONUV0>
<NSREGIONY1> / <NSREGIONUV1>
-40-
Range Initial Value
0 - 255 235
1 - 255 1
0 / 1 / 9 0 (Read only)
1 ~ 20 1
1 ~ 255 1
0 ~ 1 0
0-3 1
0 ~ 10 5
0 ~ 1 0
0 ~ 3 1
0 ~ 3 0
0 - 1 0
0 - 200 100
0 - 200 100
0 - 1 0
0 - 200 100
0 - 200 100
0 - 1 0
0 - 1 0
0 - 1 0
0 - 1 1
1 - 3 1
0 - 2 0
0 - 2 0 * Effective only for PSF signal
0 - 255 25
0 - 4 2
0 - 1 0
0 - 255 0x19
0 - 4 0x02
0 - 2 1
0 - 1023 12
0 - 1023 24
0 - 1023 40
0 - 255 50
0 - 2 1
0 - 1023 12
0 - 1023 24
0 - 1023 40
0 - 255 100
0 - 2 1
0 - 1023 12
0 - 1023 24