Using Dolby Pro Logic Ii, Dolby Digital And Dts Digital Surround (Remote Control) - JVC LVT0858-001A Instructions Manual

It will be convenient for you to use the remote control
for Surround adjustments, since you can make
adjustments from your listening point, and use the test
signal.
• When using the buttons on the front panel, see pages 36
and 37.
DVD
DVD
ANALOG/DIGITAL
INPUT
SOUND
TEST
TEST
BASS BOOST
EFFECT
SURROUND
SURROUND
ON/OFF
ON/OFF
PTY(
SURROUND
SURROUND
MODE
MODE
PTY SEARCH
TV VOL
VCR
CONTROL
/REW
DOWN
REC
RM-SRXE111R
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 15).
• You cannot adjust the center speaker output level when you have
set "CNTR SP" to "NO."
• You cannot adjust the rear speaker output levels when you have set
"REAR SP" to "NO."
• Remember not to change the speaker setting while using any
Surround modes; otherwise, it may be canceled when you
deactivate the speakers required for the Surround mode.
AUDIO
STB VCR TV
SLEEP TV DIRECT
STB VCR TV
TAPE FM AM
+
– +
BASS CENTER
1 2 3
– – +
BASS REAR•L
4 5 6
+ – +
TREBLE REAR•R
7 8 9
– – +
TREBLE SUBWOOFER
10 0 +10
100+
RETURN FM MODE
TA/NEWS/INFO
RDS
DVD
MENU
ENTER PTY9
DISPLAY MODE
DVD MENU
CHANNEL VOLUME
TV/VIDEO DIMMER MUTING
PLAY
FF/
TUNING UP
STOP PAUSE
REMOTE CONTROL
HOME CINEMA CONTROL CENTER
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround
(Remote Control)
Once you have adjusted the Surround modes, the adjustment is
memorized for each source.
• When playing back digital multichannel software (Dolby
Digital 5.1-channel or DTS Digital Surround), the
SURROUND MODE button does not work.
• For selecting Panorama control for Pro Logic II Music, use the
buttons on the front panel.
1
Select and play software you like.
2
Press SURROUND ON/OFF to activate
Surround mode.
Each time you press the button, Surround mode turns
on and off alternately.
• If you are playing back digital multichannel software such as
Dolby Digital 5.1-channel and DTS Digital Surround through
the digital input terminal, the appropriate multichannel
Surround mode is activated ("DOLBY D" or "DTS").
→ Go to step 4 .
L C R
SUBWFR LFE
DOLBY D
LS RS
Ex.: When Dolby Digital is activated.
• If you are playing back any software other than above, you
can activate Pro Logic II.
→ Go to step 3 .
If "AUTO SR (Auto Surround)" is set to "ON"
Playing a digital source automatically activates an appropriate
Surround mode. (See pages 18 and 19.) → Go to step 4 .
3
Except for the digital multichannel
software: Press SURROUND MODE
repeatedly to select "PL II MOVIE" or
"PL II MUSIC" according to a playing source.
PL II indicator lights up on the display.
PL ΙΙ
L R
LPCM
SUBWFR
4
Press TEST to check the speaker output balance.
TEST
PR ΙΙ
P
TO SR
PUT ATT
"TEST L" starts flashing on the display, and a test tone comes
out of the speakers in the following order:
(Left front speaker)
(Center speaker)
(Left rear speaker)
Notes:
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when "CNTR SP"
is set to "NO."
• No test tone comes out of the rear speakers when "REAR SP"
is set to "NO."
TO BE CONTINUED TO THE NEXT PAGE
SURROUND
ON/OFF
VOL
SURROUND
MODE
VOL
VOL
(Right front speaker)
(Right rear speaker)
33