Canon im2020 Setup Instructions
  1. Manuals
  2. Brands
  3. Canon Manuals
  4. Copier
  5. im2020
  6. Setup instructions
Canon im2020 Setup Instructions

Canon im2020 Setup Instructions

Copier and peripherals
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
im2020/2520/3520/2520f Copier
and Peripherals
SETUP INSTRUCTIONS

Advertisement

Table of Contents
loading

Related Manuals for Canon im2020

Summary of Contents for Canon im2020

  • Page 1 Copier and Peripherals SETUP INSTRUCTIONS...
  • Page 2 BLANK PAGE...
  • Page 3 Note: The System Stand must be unpacked and set in place prior to unpacking the copier. After completing the copier setup, return to the System Stand Setup Instructions in order to make the proper adjustments for the stand. Description Setup Overview for the im2020/2520/3520/2520f Copiers 9210 RADF 9211...
  • Page 4 BLANK PAGE...
  • Page 5 GMT (Standard Time) Atlantic Eastern Central Mountain Pacific Alaska Hawaii Note: Subtract an hour for Daylight Savings Time...
  • Page 6 BLANK PAGE...
  • Page 7 SETUP INSTRUCTIONS 9217 2-Way Paper Feed Cabinet NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4348-7747-02...
  • Page 8 9217 Description I Setup Overview 9210 RADF 9211 Multiposition Stapling Finisher 9216 9217 9218 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) 9218 Large Capacity Cassette (2700 sheets) 9219 Duplex Unit Copier: Printer Note: When setting 9219000000 Reversing Unit...

  • Page 9: Table Of Contents

    9217 I Unpacking 2. Remove protective tape from different parts of the Paper Feed Cabinet. 3. Remove the protective tape from the inside NOTE of the drawer. When removing the 2 Way Paper Feed Cabinet from its shipping carton, do not hold onto the reinforcement bracket (indicated by the arrow in the illustration below) (as a NOTE personal injury or a deformed frame could result).
  • Page 10 9217 I Attaching the Copier to the Paper Feed Cabinet 5. Using the Fixing Brackets and Shoulder 1. Remove the Lower Rear Cover of the copier Screws furnished with the Paper Feed (four screws). Cabinet, secure the copier to the Paper Feed NOTE Cabinet (at two places in the rear).
  • Page 11 9217 I Loading Paper 2. Install the Fixing Legs at two locations in the 1. Slide out the 3rd and 4th Drawer. front shown in the illustration. (six screws) 4348U095AA 4348U048AA 2. Load the paper stack so that it rests below the tab fitted to the Edge Guide.
  • Page 12 9217 I Checking the Paper Reference Position 7. Touch “3rd Drawer.” (This highlights the “3rd 1. Turn ON the copier. Drawer” key.) 2. Call the Tech. Rep. Mode to the screen. See the Service Manual for the procedure. 4348P017CA 4348P005CB 8.
  • Page 13 9217 I Adjusting the Paper Reference Position I Adjusting the Paper Reference Position (2) 1. Touch “END” on the Test Print screen. 1. Slide out the drawer and unload paper from 2. Loosen the three screws at the center of the Paper Lifting Plate.
  • Page 14 BLANK PAGE...
  • Page 15 SETUP INSTRUCTIONS 9218 Large Capacity Cabinet NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4348-7743-03...
  • Page 16 9218 Description I Setup Overview 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) 9218 Large Capacity Cassette (2700 sheets) Copier: Printer Note: When setting 9219 Duplex Unit up a system consisting...

  • Page 17: Check That The Following Items Are Contained In The Box Of Accessories

    9218 I Unpacking 2. Remove protective tape from the Large Capacity Cabinet. NOTE When removing the Large Capacity Cabinet from its shipping carton, do not hold onto the reinforcement bracket (indicated by the arrow in the illustration below) (as a personal injury or a deformed frame could result).
  • Page 18 9218 I Attaching the Copier to the Large Capacity Cabinet 5. Using the Fixing Brackets and Shoulder 1. Remove the Lower Rear Cover of the copier Screws furnished with the Large Capacity (four screws). Cabinet, secure the copier to the Large NOTE Capacity Cabinet (at two places in the rear).
  • Page 19 9218 I Loading Paper 2. Install the Fixing Legs at two locations in the 1. Press the Paper Descent button and then front shown in the illustration. (six screws) slide out the drawer from the Large Capacity Cabinet. 4348U098AA 4348U010AA 3.
  • Page 20 9218 I Making Settings for Paper Size I Checking the Paper Reference Position 1. Call the Tech. Rep. Mode to the screen. 1. Call the Tech. Rep. Mode to the screen. (See the Service Manual for the procedure.) (See the Service Manual for the procedure.) 4348P005CB 4348P005CB 2.
  • Page 21 9218 I Adjusting the Paper Reference Position 6. Touch “3rd Drawer.” (This highlights the “3rd 1. Touch “END” on the Test Print screen. Drawer” key.) 4348P017CA 4348P017CA 7. Press the Start key on the control panel. 2. Select “3rd Drawer” on the Registration (CD) (The copier will produce an output of a test screen.

  • Page 22: Paper Size Label

    9218 I Adjusting the Paper Reference Position (2) 4. Let the copier produce another test print and 1. Press the Paper Descent button and then check for the good paper reference position. slide out the drawer from the Large Capacity 5.
  • Page 23 SETUP INSTRUCTIONS im2020/im2520/im3520 Copiers NOTES • Keep all packing materials out of the reach of children. • Before setting up, be sure to unplug the power cord of the machine. 4030-7744-02...
  • Page 24 I Setup Overview Description 9210 RADF 9211 Multiposition Stapling Finisher 9216 9217 9218 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) 9218 Large Capacity Cassette (2700 sheets) 9219 Duplex Unit Copier: Printer...
  • Page 25 I Unpacking I Removing Protective Tape and Packaging Materials and Unlocking • Check that the following items are contained in the Box of Accessories. Scanner 1 User Manual (Basic Operations) ............1 1. Remove pieces of protective tape and packaging materials.
  • Page 26 2. Remove screws that secure the PC Drum Unit in position (two each on the right and 4. Slide out the drawer and remove the left). protective tape. Silver screws found on the lower part of the PC Drum Unit 3.
  • Page 27 10. Align the shaft of the Developing Unit with the inner guide of the PC Drum Unit. 6. Ready a packet of starter and cut off one corner of the aluminum packet with scissors. 11. Slide the PC Drum Unit along the guide to check that the positioning pin is properly aligned with the mating hole.
  • Page 28 I Plugging in Power Cord and Turning Power ON I Clearing the Counters 1. Plug in the power cord to the copier. 1. Call the Tech. Rep. Mode to the screen. (For the procedure, see the Service Manual.) 2. Connect the power cord to a power outlet.
  • Page 29 I Installing the Toner Bottle 4. Open the Toner Holder and mount the Toner NOTE Bottle. The Toner Bottle is not shipped with the copier. Purchase one that is separately available. NOTE Place the Toner Bottle so that its seal surface faces upward.
  • Page 30 I Affixing the Tray Label I Setting Time-of-Day and Date 1. Affix the Tray Label to the 1st and 2nd 1. Call the Initial Mode to the screen. (For the Drawers. procedure, see the Service Manual.) 2. Load the drawers with paper.
  • Page 31 I Installing the Original Cover Kit • Check that the following items are contained. 1. Remove the Rear Upper Cover and Hinge Covers (three screws). 1 Original Cover ..................1 2 Hinge Cover (Right) ................1 3 Hinge Cover (Left)..................1 4 Document Scanning Glass Cover ............1 5 Screw .....................5...
  • Page 32 BLANK PAGE...
  • Page 33 SETUP INSTRUCTIONS im2520f Copier NOTES • Keep all packing materials out of the reach of children. • Before setting up, be sure to unplug the power cord of the machine. 4032-7744-02...
  • Page 34 im2520f I Setup Overview Description 9210 RADF 9211 Multiposition Stapling Finisher 9216 9217 9218 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) 9218 Large Capacity Cassette (2700 sheets) Copier: Printer 9219 Duplex Unit Note: When setting 9219000000 Reversing Unit...
  • Page 35 im2520f I Unpacking I Removing Protective Tape and Packaging Materials and Unlocking • Check that the following items are contained in the Box of Accessories. Scanner 1 User Manual (Basic Operations) ............1 1. Remove pieces of protective tape and packaging materials. 2 User Manual (Advanced Operations).............1 3 User Manual (Fax Operations)...............1 4 Setup Instructions (this manual).............1...
  • Page 36 im2520f 2. Remove screws that secure the PC Drum Unit in position (two each on the right and 4. Slide out the drawer and remove the left). protective tape. Silver screws found on the lower part of the PC Drum Unit 3.
  • Page 37 im2520f 10. Align the shaft of the Developing Unit with the inner guide of the PC Drum Unit. 6. Ready a packet of starter and cut off one corner of the aluminum packet with scissors. 11. Slide the PC Drum Unit along the guide to check that the positioning pin is properly aligned with the mating hole.
  • Page 38 im2520f I Plugging in Power Cord and Turning Power ON I Clearing the Counters 1. Plug in the power cord to the copier. 1. Call the Tech. Rep. Mode to the screen. (For the procedure, see the Service Manual.) 2. Connect the power cord to a power outlet. 2.
  • Page 39 im2520f I Installing the Toner Bottle 4. Open the Toner Holder and mount the Toner NOTE Bottle. The Toner Bottle is not shipped with the copier. Purchase one that is separately available. NOTE Place the Toner Bottle so that its seal surface faces upward.
  • Page 40 im2520f I Affixing the Tray Label I Setting Time-of-Day and Date 1. Affix the Tray Label to the 1st and 2nd 1. Call the Initial Mode to the screen. (For the Drawers. procedure, see the Service Manual.) 2. Load the drawers with paper. 4030U025AB I Attaching the Operator’s Manual Holder 4030P003CA...
  • Page 41 im2520f I Installing the Original Cover Kit • Check that the following items are contained. 1. Remove the Rear Upper Cover and Hinge Covers (three screws). 1 Original Cover ..................1 2 Hinge Cover (Right) ................1 3 Hinge Cover (Left)..................1 4 Document Scanning Glass Cover ............1 5 Screw .....................5 4599U005AB 2.
  • Page 42 BLANK PAGE...
  • Page 43 SETUP INSTRUCTIONS 9210 Duplexing Document Feeder NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4344-7741-01...
  • Page 44 9210 ■ Setup Overview Description 9210 RADF 9216 9218 9217 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) 9218 Large Capacity Cassette (2700 sheets) Copier: Printer Note: When setting 9219 Duplex Unit up a system consisting...
  • Page 45 9210 ■ Unpacking ■ Installing the Duplexing Document Feeder 1. Check that the following items are contained in the Box of Accessories. 1. Install the two Shoulder Screws furnished 1 Shoulder Screw ..................2 with the Duplexing Document Feeder to the hinge mounting portion.
  • Page 46 9210 ■ Adjusting the Height of Duplexing Document Feeder 5. Connect the hookup harness connector of 1. Place the Document Pad, with its side to which sponges are affixed facing up, onto the the Duplexing Document Feeder to the Original Glass. mating connector on the copier side.
  • Page 47 9210 ■ Checking for Skew Feed 4. Turn the screw on the left hinge as 20 mm 1. Prepare a test chart (A4 or Letter) as shown. necessary so that you feel resistance when 2. Plug in the power cord and turn ON the pulling out the strip of paper.
  • Page 48 9210 ■ Adjusting Skew Feed ■ Checking the Reference Zoom Ratio 1. Loosen the screw shown and adjust the 1. Prepare a test chart (A3 or 11× 17) as shown. position of the Automatic Document Feeder Draw a 270-mm-long straight reference line as detailed below.
  • Page 49 9210 ■ Adjusting the Reference Zoom Ratio 6. Make the Zoom Adjustment. 1. Call the Tech. Rep. Mode to the screen. (See the Service Manual for the procedure.) A (CD) / B (FD) 2. Touch “Tech. Rep. Choice.” 4344P010CA · If the line is longer than the specifications, adjust toward the reduction side.

  • Page 50: Adjusting Registration

    9210 ■ Checking for Registration ■ Adjusting Registration 1. Prepare a test chart (A3) as shown. 1. Call the Tech. Rep. Mode to the screen. Draw a straight reference line at a point 20 (See the Service Manual for the procedure.) mm from the rear edge and another at a point 20 mm from the top edge of the chart.
  • Page 51 9210 ■ Affixing the Document Pad 1. Raise the Duplexing Document Feeder. 2. With the rear edge of the Document Pad 0 mm pressed up against the Original Length Scale, place it on the Original Glass so that its left edge is 0.5 to 1.0 mm away from the 0.5 to 1 mm Original Width Scale.
  • Page 52 BLANK PAGE...

  • Page 53: Setup Instructions (This Manual)

    SETUP INSTRUCTIONS 9219 Duplex Unit NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. • When the Duplex unit is installed, it is necessary to install the switchback unit at the same time. 4346-7741-02...
  • Page 54 9219 I Setup Overview Description System 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: When setting 9219 Duplex Unit up a system consisting...
  • Page 55 9219 I Unpacking I Installation 1. Check that the following items are contained in the Box of Accessories. 1. Remove four screws from the Right Door of 1 Coil Spring....................1 the copier. 2. Remove the cover of the Right Door of the 2 Screw (9735-0306).................1 copier (one screw).
  • Page 56 9219 6. Slightly raise the Right Door of the copier 9. Tighten the four fixing screws of the Duplex and, at the same time, remove the Lower Unit. Side Right Cover of the copier. NOTE Note the locking tab provided on the left side Tighten the screws in the following order.
  • Page 57 9219 I Replacing the Coil Spring 5. Remove the coil spring fitted to the copier 1. Open the Front Door of the copier. and, instead, fit the Coil Spring furnished with the Duplex Unit in position. NOTE When replacing the coil spring, keep the Right Door of the copier closed.
  • Page 58 9219 I Checking the Paper Reference Position 7. Touch “Duplex.” (This highlights the “Duplex” 1. Turn ON the copier. key.) 2. Call the Tech. Rep. Mode to the screen. See the Service Manual for the procedure. 4348P017CA 4348P005CB 8. Press the Start key on the control panel. 3.
  • Page 59 9219 I Adjusting the Paper Reference Position 1. Touch “END” on the Test Print screen. 4348P017CA 2. Select “Duplex” on the Registration (CD) screen. (This highlights the “Duplex” key.) 4348P015CA 3. Press the Clear (C) key and, using the 10- Key Pad, change the setting value as detailed below.
  • Page 60 BLANK PAGE...
  • Page 61 SETUP INSTRUCTIONS 9219000000 Switchback (Reversing) Unit NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4526-7741-02...
  • Page 62 9219000000 I Setup Overview Description 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: Wh en setting 9219 Duplex Unit up a system consisting...
  • Page 63 9219000000 I Unpacking I Removing the Fusing Unit 1. Check that the following items are contained in the Box of Accessories. 1. Pull the Lock Release Lever and open the 1 Tray ......................1 Right Door of the copier. 2 Upper Switchback Unit................1 3 Lower Switchback Unit................1 4 Shoulder Screw (3 mm) .................2 5 Screw (9733-0308-13) ................2...
  • Page 64 9219000000 I Removing the Fusing Cover 5. Unplug the three connectors of the Hookup 1. Remove one screw from the Fusing Cover. Harness of the Fusing Cover and that of the 2. Unhook the hooks (at three places) on the Fusing Unit.
  • Page 65 9219000000 I Installing the Switchback Unit 4. Install the Upper Switchback Unit to the 1. Remove the cover with a lever from the rear copier. side of the copier (one screw). The removed cover will not be used. NOTES • Make sure that the protrusions on the lower side of the Upper Switchback Unit are positively fitted into the positioning holes in the upper surface of the Fusing...
  • Page 66 9219000000 I Installing the Covers 1. Remove the small cover from the Column Support Cover on the control panel side (one screw). This is the Column Support Cover that has been removed in step 4 on p. 2. 4625U020AA 2. Install the Column Support Cover on the control panel side (one screw).

  • Page 67: Job Separator

    SETUP INSTRUCTIONS ZC3500070 Job Separator NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4347-7741-02...
  • Page 68 ZC3500070 I Setup Overview Description 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: W hen setting 9219 Duplex Unit up a system consisting...
  • Page 69 ZC3500070 I Unpacking I Installation • Check that the following items are contained in the Box of Accessories. NOTE 1 Tray ......................1 To install the Job Separator, the copier must be previously equipped with a 2 Sensor Unit ....................1 Switchback Unit. 3 Screw A (3 ×...
  • Page 70 ZC3500070 4. Unplug the connectors of the Switchback 9. Remove the cover (two screws). Unit. 4347U005AA 4347U009AA 5. Remove the screws at the front (two screws). 10. Press the Sensor Unit up against the Switchback Unit and secure the Sensor Unit 6.
  • Page 71 ZC3500070 13. Install the Switchback Unit. 21. Erect the column support of the Tray. 14. Install the screws that have been removed in 22. Secure the Tray using Screw B (one screw). step 5 (two screws). 15. Tighten the screws that have been loosened in step 6 (two screws).
  • Page 72 BLANK PAGE...
  • Page 73 SETUP INSTRUCTIONS 9211 Built-in Finisher NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4349-7741-02...
  • Page 74 9211 I Setup Overview Description 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: When setting 9219 Duplex Unit up a system consisting...
  • Page 75 9211 I Unpacking 1. Check that the following items are contained in the Box of Accessories. 1 Finisher Unit ...................1 2 Tray Unit....................1 3 Front Cover ....................1 4 Secondary Cover ...................1 9735 9739 9646 9735 5 Exit Tray (Upper) ..................1 6 Exit Tray (Lower) ..................1 2.
  • Page 76 9211 I Removing Protective Tape and Fixing Brackets 1. Remove pieces of protective tape. 4. Screw screws 1 and 2, which have been unscrewed from the fixing bracket in step 2, <Finisher Unit> <Tray Unit> to the Staple Unit (two screws). Screw them into the positions, from which they have been unscrewed.
  • Page 77 9211 I Installing the Finisher Unit 6. Holding the positions indicated by the arrows 1. Open the Front Door. in the illustration, place the Finisher Unit onto the rail of the copier. 2. Remove the Exit Cover (three screws). Rail 4349U026AC 4346U002AA 7.
  • Page 78 9211 I Installing the Tray Unit 10. Loosen the adjusting screw and move the 1. Make sure that the Paddle of the Finisher Unit is not advanced. Finisher Unit to the right or left as necessary (one screw). 2. If the Paddle is advanced, push the solenoid shown and turn the Misfeed Clearing Dial to bring the Paddle into its retracted position.
  • Page 79 9211 5. Using Screw B, secure the ground wire. 10. Install the Front Cover to the copier. NOTE Make sure that the ground wire runs in the direction shown in the illustration when secured. 4349U034AB 4349U055AA 6. Connect the connector. 11.
  • Page 80 9211 16. Using Screw D, secure the band and the Retaining Plate to the Secondary Cover (one screw). 17. Fit the label back to the Front Cover. 18. Close the Front Cover. 4349U041AB 19. Fit the upper and lower Exit Trays and secure them in position using Screws D (two screws each).

  • Page 81: Punch Kit

    SETUP INSTRUCTIONS 9212 Punch Kit NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4512-7741-02...
  • Page 82 9212 Setup Overview Description 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: When setting 9219 Duplex Unit up a system consisting...
  • Page 83 9212 Unpacking Installation • Check that the following items are contained in the Box of Accessories. NOTE 1 Punch Unit....................1 It is recommended that the Punch Kit be installed to the copier before the Finisher is 2 Sensor Unit ....................1 mounted to the copier.
  • Page 84 9212 5. Remove the guide plate (two screws). 10. Withdraw the connector of the Sensor Unit through the hole shown in the illustration. 11. Open the cord clamp. 12. Connect the connector and close the cord clamp. 4512U009AB 4512U028AB 6. Remove the cover (two screws). 13.
  • Page 85 9212 17. Press the Punch Unit tightly up against the 23. Install the Punch Box. copier frame. 24. Reinstall the Finisher cover that has been 18. Tighten the screw shown to secure the removed in step 3 (four screws). Punch Unit in position (one screw). 25.
  • Page 86 9212 Adjustment 1. Make a copy in the Punch mode. 7. Affix the Label to the Front Cover. 2. Fold the copy into halves and check for possible deviation in hole positions. Specifications: 0 ± 2 mm 4512U027AA 4512U023AB 4512U024AB 3.

  • Page 87: Saddle Stitch Finisher

    SETUP INSTRUCTIONS 9214 Saddle Stitch Finisher NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. • When the Duplex unit is installed, it is necessary to install the switchback unit at the same time. 4511-7741-02...
  • Page 88 9214 Setup Overview Description 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: When setting 9219 Duplex Unit up a system consisting...
  • Page 89 9214 Unpacking • Check that the following accessories are available. 1 Saddle Unit.....................1 2 Creasing Unit ..................1 3 Exit Tray ....................1 4 Shutter....................1 5 Mounting Bracket (Right) ...............1 4511U005AA 4511U006AA 4511U007AA 6 Mounting Bracket (Left)................1 7 Shutter Mounting Holder ................2 8 Creasing Unit Adjusting Plate ..............1 9 Harness....................1 10 Mounting Bracket Cover.................1...
  • Page 90 9214 Removing Protective Tape Installing the Creasing Unit 1. Remove the Finisher. NOTE When mounting the Saddle Kit, it is recommended that the kit be installed before the NOTE Finisher is mounted to the copier. For the Finisher removal procedure, see Setup Instructions for 9211.
  • Page 91 9214 5. Carefully insert the Creasing Unit into the copier along the groove provided in the rear of the copier. 7. Secure the rear end of the Creasing Unit using Shoulder Screw A (1 screw). NOTE Use care not to allow the parts shown in the illustration to hit against the mating NOTE portions while the Creasing Unit is being inserted.
  • Page 92 9214 13. Reinstall the cover which has been removed 3. Move the Shutter up and down. Release the in step 11. Shutter from a higher position to check to Be sure first to fit the tab into position. ensure that the Shutter falls by its own (1 screw) weight.
  • Page 93 9214 9. Remove the knockouts. 13. Reinstall the Exit Tray mounting holder (left) which has been removed in step 7. (1 screw) NOTE Install the holder at a level one step lower than where it was removed in step 7. 4510U013AA 4511U030AA 10.
  • Page 94 9214 17. Loosen the screw shown, move it to the 22. Place the Mounting Bracket Cover over the front, and then tighten it again. (1 screw) Mounting Bracket. 23. Secure the Saddle to the Mounting Bracket NOTE (Right) using Screw C. This step must be performed properly to Tighten the Saddle together with the Mount- prevent any trouble.
  • Page 95 9214 Adjustments [If the crease deviates as shown on the left] <Crease Tilt Adjustment> 10. Fold the copy fed out along the crease. 1. Load the drawer with A3 or Ledger paper. 11. Check the crease for deviation. (Measure 2. Select the Crease mode and make a copy Center width A.) (A3 or Ledger copy).
  • Page 96 9214 20. Open the Saddle Unit Lock Release Lever. [If the Staple positions deviate as shown on the 21. Loosen the adjusting screw and move the left] Saddle to the left or right to adjust tilt as 28. Fold the copy fed out along the crease. necessary.

  • Page 97: Output Bin

    SETUP INSTRUCTIONS ZC3500060 Output Bin NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4030-7772-02...
  • Page 98 ZC3500060 Setup Overview Description 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: When setting 9219 Duplex Unit up a system consisting...
  • Page 99 ZC3500060 Unpacking Installation: If 9214 is not mounted • Check that the following items are contained in the Box of Accessories. 1. Using Screws B, secure the Exit Tray 1 Exit Tray ....................1 Mounting Holder (Right) and Exit Tray Mounting Holder (Left) (one screw each). 2 Exit Tray Mounting Holder (Right) ............1 3 Exit Tray Mounting Holder (Left) ............1 4 Screw A (3 ×...
  • Page 100 ZC3500060 Installation: If 9214 is mounted 8. Plug the short connector into the empty 1. Using Screws B, secure the Exit Tray connector of the Finisher. Mounting Holder (Right) and Exit Tray Mounting Holder (Left) (one screw each). 4349U054AA 4349U005AC 9.
  • Page 101 ZC3500060 8. Plug the short connector into the empty connector of the Finisher. 4349U054AA 9. Reinstall the Secondary Cover (two screws). NOTE Make sure that there is a uniform clearance between the Misfeed Clearing Dial and Secondary Cover. 4349U036AC 10. Reinstall the Secondary Cover (one screw). 11.
  • Page 102 BLANK PAGE...
  • Page 103 OPTIONAL MEMORY BOARD SET-UP INSTRUCTIONS (2) In case of a Network Interface Card installed model, remove the Before installation, you must read this card. (3 screws) instruction sheet and understand the (3) Disconnecting Ni-MH battery cable. correct method of installation. CAUTION! 1.
  • Page 105 Network Scan Kit (ZC3500110)/Internet Fax & Network Scan Kit (ZC3500120) Installation Guide 1. Contents of Kit 2. Remove the I/F CLAN circuit board cover. Item Note Cable connectors • Disconnect the 2 cable connectors. Network Scan Circuit Board (96 MB) Network Scan Kit (ZC3500110) only •...
  • Page 106 Network Scan Kit (ZC3500110)/Internet Fax & Network Scan Kit (ZC3500120) Installation Guide (3) Install the network interface card Add the network interface card. 2. Install the circuit board that comes with this kit into expansion slot 2 (CN5) on the See the Network Interface Card Installation Guide for more information.
  • Page 107 Printer Controller (ZC3500080)/Printer Controller (ZC3500130/PS) Installation Guide 1. Contents of Kit 2. Remove the I/F CLAN circuit board cover. Item Note Cable connectors • Disconnect the 2 cable connectors. Printer Circuit Board (32 MB) ZC3500080 only • Remove the 2 cables from the cable clamp.
  • Page 108 Printer Controller (ZC3500080)/Printer Controller (ZC3500130/PS) Installation Guide (2) Installing the printer circuit board (3) Replace the CompactFlash card (only with the ZC3500130) 1. With the im2520f, disconnect the Ni-MH battery cable from CN3 on 1. Remove the ROM cover on the right side of the MFB3 circuit board.

  • Page 109: Network Interface Card

    INSTALLATION GUIDE Network Interface Card (ZC3500090) NOTE • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. ND-100096(E) 4513-7746-02...

  • Page 110: Operating Environment

    1. Operating Environment Network Interface Card (ZC3500090) 1. CLAN Circuit Board....................1 Printer controllers (ZC3500080 and ZC3500130) operate under the following environment. 2. Card Spacer ....................... 1 3. CLAN Finger ......................1 Computer IBM PC or compatible PC : Pentium processor or higher 4.
  • Page 111 I Required tool: 3. Installation I Setup Overview • Phillips screwdriver • Before performing any operations, check that the amount of available memory is 100%. 9216 9217 9218 • If the amount of available memory is not 100%, explain this to the customer, and then either print out or delete any data in the memory.
  • Page 112 2. Remove the I/F CLAN circuit board cover. 5. Remove the bracket (connector). Cable connectors • Disconnect the 2 cable connectors. Remove the bracket (connector) plate. (1 • Remove the 2 cables from the cable screw) clamp. • Remove the I/F CLAN circuit board cover. (6 screws) C4514U003AA (2) Installing the memory circuit board...
  • Page 113 4. With the im2520f, reconnect the Ni-MH battery cable to CN3 on the MFB3 circuit board. 2. Install one of the following memory circuit boards into expansion slot 1 (CN4) on the MFB3 circuit board. NOTE • Printer memory circuit board (for ZC3500080) If the cable is not reconnected, there will be no backup power in case of a power failure.
  • Page 114 Installing the Network Interface Card (ZC3500090) (1) Preparing to install the CLAN circuit board After affixing the CLAN sheet to the CLAN cir- (Only for Europe) cuit board, attach the plate. 1. Attach the card spacer to the MFB3 circuit board.
  • Page 115 (3) Cutting an opening for the external line terminals 4. Checks After Installation Cut along the perforations in the rear cover to Perform the following operations and checks on the copier control panel. create an opening for the LAN and USB exter- If a printer controller (ZC3500080/ZC3500130) is installed: nal line connectors.

  • Page 116: Connecting The Cables

    5. Specifying Machine Settings Priority Device (Only for Europe) Specify the print timing for received print jobs. 1. Press the [Utility] key. 2. Touch [User Set]. 3. Touch [User’s Choice]. 4. Touch [Priority Device] on tab 6/6. Cable tie 5. Select either “Copier” or “Printer”, and then touch [OK]. Copier: Printing begins after the data for all pages of the print job is received.

  • Page 117: User Environment

    7. User Environment NOTE The following procedures are basically for administrators. Refer to the following only if a • Windows NT 4.0 does not support USB. request for setup is received from the user. • If the copier is to be connected to a PC, in which Windows 98 or 98SE is installed, through USB, it is necessary that the USB device driver be installed in the PC.
  • Page 118 Network Connection That Can be Selected in Each of Different Windows OSs Starting PageScope Light Different setting procedures apply depending on the output method (LPR, Windows Print- • This is the tool for making settings from the Web browser of the PC connected to the ing, IPP).
  • Page 119 Peer-to-Peer Printing NOTE When you want to print directly to a network printer from Windows 98/Me without going Refer to the “Windows” of PageScope Light for the NetBIOS name and the Printing Ser- through the server, install PageScope Network Setup from the PageScope CD (for admin- vice name.
  • Page 120 NetWare Printing Setting Scanning Functions Settings made on the controller side Specify settings for the scanning functions that can be used, depending on whether the network scan kit (ZC3500110) or Internet fax & network scan kit (ZC3500120) is installed. Settings are made to permit printing in the NetWare environment from PageScope Light. There are two ways to specify the settings: from the control panel of the copier or from the Web browser on a computer connected to the network (PageScope Light).
  • Page 121 • Specifying network settings Operation 1. Press the [Utility] key. 2. Touch [Admin. Management], [Admin. 2], then [Network Setting]. 3. Specify the following settings, depending on the scanning functions to be used. G: Required; 2: Available L: Necessary depending on environment; -: Unnecessary Parameter Operation Equipment Name...
  • Page 122 • Specifying settings using PageScope Light Operation 1. Start up PageScope Light. 2. Log into PageScope Light in Administrator mode. 3. Specify the following settings, depending on the scanning functions to be used. G: Required; 2: Available L: Necessary depending on environment; -: Unnecessary Parameter Scanner Settings screen Operation...

  • Page 123: Printing Functions

    I Printing Functions 1. Press the [Utility] key. 2. Touch [User Set], [FAX Input], then [One-Touch]. When printing cannot be effected over the network (With the im2020, im2520 and im3520, touch [User Set], [Mail Input], then [One-Touch].) Check Possible Cause Action 3.

  • Page 124: Scanning Functions

    I Scanning Functions Internet FAX Reception Scan to E-mail/Internet FAX Transmission Condition Possible Cause Action Cannot receive. The LAN cable is not con- Correctly connect the LAN Condition Possible Cause Action nected correctly or there is a cable and restart or replace Cannot send.
  • Page 125 Scan to PC (FTP) Transmission Network FAX Transmission Condition Possible Cause Action Condition Possible Cause Action Cannot send. The LAN cable is not con- Correctly connect the LAN Data is not reaching The LAN cable is not con- Correctly connect the LAN nected correctly or there is a cable and restart or replace the machine.
  • Page 126 BLANK PAGE...
  • Page 127 SETUP INSTRUCTIONS ZC3500050 Hard Disk Drive Kit NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. • Before mounting the Hard Disk Drive Kit, be sure to install the Net- work Interface Card separately available as an option.
  • Page 128 ZC3500050 I Setup Overview Description 9210 RADF 9216 9217 9218 9211 Multiposition Stapling Finisher 9212 Punch Unit 9214 Saddle Stitch Finisher 9216 Plain Stand 9217 Copy Desk (550 x 2) Copier: Printer 9218 Large Capacity Cassette (2700 sheets) Note: When setting 9219 Duplex Unit up a system consisting...
  • Page 129 ZC3500050 I Unpacking NOTE 1. Check that the following items are contained in the Box of Accessories. If the Hard Disk Drive Kit is to be mounted at the same time that the Network 1 Mounting Bracket ...................2 Interface Card separately available as an option is mounted, be sure to mount the Network Interface Card first and then mount the Hard Disk Drive Kit.
  • Page 130 ZC3500050 4. Remove the Hookup Harness of the copier 8. Remove the reinforcement plate (four from the wiring saddle. screws). NOTE Note that the type of the harness differs between that for the copier and that for the fax machine. 4599U041AB 4599U036AA 5.
  • Page 131 ZC3500050 I Assembling the Hard Disk Drive 4. With the M marking on the Hard Disk Drive 1. Secure the two Mounting Brackets that come used as reference, connect the Flat Cable. with the Hard Disk Drive to the board side of the Hard Disk Drive (four 9654-0304 NOTES screws).
  • Page 132 ZC3500050 I Installing the Power Supply Unit I Wiring the Power Harness 1. Remove two handles and the cover from the 1. Connect the Harness that comes with the rear of the copier (six screws). Hard Disk Drive to the Power Supply Unit. 4599U010AA 4599U018AA 2.
  • Page 133 ZC3500050 I Installing the Hard Disk Drive to the Copier 5. Affix the Protective Film furnished with the 1. Reinstall the Mechanical Board Cover to the Hard Disk Drive to the reinforcement plate. copier (five screws). NOTE NOTE Clean the surface of the reinforcement Use care not to allow the harness on the 4599U042AA plate, to which the Protective Film is to be...
  • Page 134 ZC3500050 I Installing Covers I Setting the Hard Disk Drive 1. Reinstall the handle and cover to the rear of 1. Turn ON the Power Switch. the copier (six screws). 2. Call the Tech. Rep. Mode to the screen. (For the procedure, see the Service Manual.) 3.
  • Page 135 ZC3500050 I Formatting the Hard Disk 7. When the message “The Hard Disk format 1. Turn ON the Power Switch. completed” appears, touch “OK” on the lower 2. Call the Tech. Rep. Mode to the screen. right corner of the screen. (For the procedure, see the Service Manual.) 3.
  • Page 136 BLANK PAGE...
  • Page 137 SETUP INSTRUCTIONS ZC3500100 Parallel Interface Kit NOTES • Before setting up, be sure to unplug the power cord of the machine. • Keep all packing materials out of the reach of children. 4513-7749-01...

  • Page 138: Package Contents

    I Package Contents 3. Remove the back panel. (13 screws) (When • Parallel interface circuit board .................1 removing the panel, slightly lift it up.) • Relay harness......................1 • Power relay harness ....................1 • Mounting plate (for the external connectors) ............1 •...
  • Page 139 7. Remove the current mounting plate (2 screws), and then install the enclosed mounting plate (for the external connectors) (2 screws). A. If the external connector has shape A, as shown in the illustration, continue with steps 6 through 9. B.
  • Page 140 9. Install the cover over the external connectors. (2 screws) 13. Remove the two screws from the connector 10. Remove the screw at the rear of the on the parallel interface circuit board. machine. C4513U108AA 14. Attach the parallel interface circuit board to the rear of the machine, and then secure it to the mounting plate using the two screws that were removed.
  • Page 141 16. Attach the four wire holders for the relay 19. Remove the power supply fan. (2 screws) harness to the rear of the machine. C4513U114AA 20. Disconnect the 2-pin connector for the low- voltage power supply. C4513U111AA 17. Connect the relay harness connector to the connector (CN8) on circuit board MFB3.
  • Page 142 22. Insert the 2-pin connector disconnected in 25. Insert the connector on the power relay step 20 into the relay connector for the harness into the connector on the parallel power relay harness. interface circuit board. C4513U118AA C4513U120AA 26. Install the Printer Controller and the Network Interface Card. See the Network Interface Card Installation Guide for more information.

  • Page 143: Installing The Printer Driver

    I Connecting the Cables I Installing the Printer Driver The procedure described below may differ slightly depending on the operating system 1. Connect the IEEE1284 (Centronics) cable to the parallel connector on the copier, and being used. then secure both connectors with the locking clips. 1.

This manual is also suitable for:

Im2520Im3520Im2520f

Table of Contents