Related Manuals for DeWalt XR Li-Ion DCD790-XE
Summary of Contents for DeWalt XR Li-Ion DCD790-XE
-
Page 1: Instruction Manual
INSTRUCTION MANUAL DCD790-XE 18V BRUSHLESS CORDLESS COMPACT 13 mm DRILL/DRIVER DCD795-XE 18V BRUSHLESS CORDLESS COMPACT 13 mm DRILL/DRIVER/HAMMERDRILL... -
Page 3: Definitions: Safety Guidelines
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, Vibration emission value a CALL US AT: 1800 338 002 (Aust) or 0800 339 258 (NZ). Drilling into metal Technical Data m/s² DCD790-XE DCD795-XE Uncertainty K = m/s² Voltage Vibration emission value a Battery Type... - Page 4 accessories or poorly maintained, the vibration emission may differ. This may c) Keep children and bystanders away while operating a power tool. significantly increase the exposure level over the total working period. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY An estimation of the level of exposure to vibration should also take into account a) Power tool plugs must match the outlet.
-
Page 5: Electrical Safety
d) Remove any adjusting key or wrench before turning the power tool on. A 5) BATTERY TOOL USE AND CARE wrench or a key left attached to a rotating part of the power tool may result in a) Recharge only with the charger specified by the manufacturer. A charger personal injury. -
Page 6: Extension Cords
• Replacement of the supply cord. If the supply cord or plug is damaged, it must WARNING: ALWAYS wear approved protective safety equipment complying with be replaced by the manufacturer or an authorised D WALT Service Centre in the following standards: order to avoid a hazard. -
Page 7: Important Safety Instructions For All Battery Packs
NOTE: Do not store the battery packs in a tool with the trigger switch locked or DC ..direct current or AC/DC ..alternating or on. Never tape the trigger switch in the ON position....Class I Construction direct current WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If (grounded) no .......no load speed the battery pack case is cracked or damaged, do not insert into the charger. -
Page 8: Important Safety Instructions For All Battery Chargers
Important Safety Instructions for All Battery Chargers • Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal SAVE THESE INSTRUCTIONS: This manual contains important safety and operating heat. -
Page 9: Charge Indicators
Indicator Light Operation NOTE: This could also mean a problem with a charger. PROBLEM POWERLINE PACK CHARGING Some chargers have a problem powerline indicator. When the charger is used with some portable power sources such as generators or sources that convert DC to AC, the PACK CHARGED charger may temporarily suspend operation, flashing the red light with two fast blinks followed by a pause. -
Page 10: Storage Recommendations
be kept away from charger cavities. Always unplug the charger from the power FIG. 2 supply when there is no battery pack in the cavity. Unplug the charger before attempting to clean. 7. Do not freeze or immerse the charger in water or any other liquid. WARNING: Shock hazard. - Page 11 INTENDED USE NOTE: The torque adjustment collar is only engaged during screwdriving mode and not in drill and hammerdrill modes. These drills/drivers/hammerdrills are designed for professional drilling, percussion drilling and screwdriving applications. Dual Range Gearing (Fig. 2) DO NOT use under wet conditions or in presence of flammable liquids or gases. The dual range feature of your drill/driver allows you to shift gears for greater These drills/drivers/hammerdrills are professional power tools.
- Page 12 The belt hook (G) and bit clip (I) can be attached to either side of the tool using only FIG. 3 FIG. 4 FIG. 5 the screw (H) provided, to accommodate left- or right- handed users. If the hook or bit clip is not desired at all, it can be removed from the tool.
- Page 13 Drilling (Fig. 9) It does not indicate tool functionality and is subject to variation based on product components, temperature and end-user application. NOTICE: If drilling thin material, use a wood “back-up” block to prevent damage to the For more information regarding fuel gauge battery packs, please contact Stanley Black material.
- Page 14 5. Always start with lower torque settings, then advance to higher torque settings to MAXIMUM RECOMMENDED CAPACITIES avoid damage to the workpiece or fastener. DCD790-XE DCD795-XE FIG. 9 FIG. 10 FIG. 11 WOOD Auger 22 mm (7/8") 22 mm (7/8") Paddle 32 mm (1-1/4")
- Page 15 CHARGER CLEANING INSTRUCTIONS WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Repairs This charger and battery pack are not serviceable.
- Page 16 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (MAR13) Part No. N217114 DCD790-XE, DCD795-XE Copyright © 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...