Troubleshooting - Drayton MiStat P710R User Manual

Step 7: Additional User Settings
Start at "Home Screen"
→
Feature: Description:
Programme Temperature and time for the current period can be
Timetable
modified. See description in 'Step 5'
Copy days Will copy the current day to one or more other days
Add period Adds a Time/Temperature event. It will be added
at the correct position within the day. There is a
maximum of 8 periods.
Remove period Removes the selected period. There needs to be at
least two periods
Change The visible day-blocks available in "Programme
timetable type timetable" can be defined
Individual days Each day can be programmed individually
Week and Mon... Fri and Sat... Sun can be programmed as 2
weekend blocks
All week Mon...Sun can be programmed as one block
Stored MiStat contains 3 pre-set programmes, see step 6.
programmes
The 3 user profiles can be saved by name and
restored.
Load stored A pre-set programme can be loaded by name
programme
Save current The current programme can be saved by name (Each
programme pre-set program includes: Individual days, week/
weekend, all day and custom day schedules)
Step 9: Receiver - Key & LED
LED colour Mode Action
Green Normal Call for heat (boiler is firing)
Green Flashing Normal RF communication
Off Normal No call for heat (boiler is not firing)
Red RF loss or not bound No call for heat
Amber RF loss or not bound Call for heat
6444 Invensys MiStat Prog User 06490190001 IssE.indd 2
→
Factory Pre-Set: Feature: Description:
Help Tips Describes the button functions
Holiday A specific temperature can be set from .... until a date In the period until
switch off holiday starts the product will operate normally. If holiday is disabled
manually or terminates automatically, the mode before start of holiday will
be re-instated. An enabled holiday will be indicated with a suitcase symbol
in the top line. If holiday is active, in the Set: line the holiday end date will be
indicated. In the Summary screen the suitcase will be visible together with
the holiday temperature.
Status Enable or disable holiday mode.
Holiday Set the temperature to be controlled during your
temperature holiday
Holiday start Set the time for the start of your holiday
time (From)
Default
Holiday start Set the date for the start of your holiday
date (From)
Holiday end time Set the time for the end of your holiday
Programme 1 (To)
Holiday end date Set the date for the end of your holiday
(To)
Time and date settings
Set time To set time of day
Set date
To set date
Daylight saving To enable or disable daylight saving
Clock format
To select 12h or 24h clock mode

Troubleshooting

1
a
b
LED: See table below for details
c
d
2
a
Key: See table below for details
3
a
4
a
5
a
Key Function
6
None
None a
None
7
Switches the boiler On
a
Switches the boiler Off
Step 8: Changing the Batteries
How do I know when to change
the batteries?
When the batteries start to run low a battery icon will
Press Select to
flash in the display to indicate "low battery", during
enter a specific this time the MiStat will function normally. When
Setting. Options
the battery icon alone is shown in the display, the
shown below:
batteries are completely exhausted and the MiStat will
cease to function (see below). Re-activate by replacing
the batteries.
Factory Pre-Set:
Disabled
16°C
Current time -
nearest hour
Today
Current time -
nearest hour
Today + 1 week
Factory set
Factory set
Enabled
12hr
It is not warm early enough User Programme:
✎
Are time and temperature periods set correctly?
Programme 1
Is Optimum start switched on? (see Installation Guide Step
5 Installer settings/System settings)
Did the thermostat have enough time (a few days) to
determine the room data?
Was the radio link established properly and is it still
active? (see Installation Guide Step 5 Installer settings/
1st event
Signal Strength)
2nd event
Heating is starting earlier than set in the programme
3rd event
Is the Optimum start switched on? (see Installation Guide 4th event
Step 5 Installer settings/System settings)
5th event
Setting temperature values are restricted
6th event
7th event
Are Minimum/Maximum temperatures activated ? (see
Installation Guide Step 5 Installer settings/Zone settings)
8th event
No Signal is visible on the screen, no reaction on key
presses anymore
Is the receiver powered? (Red signal lamp should be
visible) Programme 2
Service due or overdue is visible on the screen, no
reaction on key presses
Check the service feature, see Installation Guide Step 5
1st event
Initialising... Press to force re-bind is visible on the
screen, no reaction on key presses anymore
2nd event
Is the receiver powered? (Red signal lamp should be
3rd event
visible)
4th event
Please wait... Press to force re-bind is visible on the
5th event
screen, no reaction on key presses anymore
6th event
Is the receiver powered? (Red signal lamp should be
visible)
7th event
8th event
How to replace the batteries
Remove the battery covers as shown. Replace the
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries
ensuring correct orientation. Replace the battery
covers pressing fully home.
Battery Covers:
Slide outwards to remove
Battery Handling
Batteries, rechargeable or not, should not be disposed
of into ordinary household waste. Instead, they must be
recycled properly to protect the environment and cut down
the waste of precious resources.
Your local waste management authority can supply details
concerning the proper disposal of batteries.
In compliance with the EU Directive 2006/66/EC, the
button cell battery located on the printed circuit board
inside the product, can be removed at the end of the
product life, by professional personnel only.
Programme 3
All week Week & Weekend or All week
Individual Days
Mon-Sun Mon-Fri Sat-Sun Mon-Sun
Time Temp Time Temp Time Temp Time
1st event
2nd event
3rd event
4th event
5th event
6th event
7th event
8th event
User Notes:
✎
All week Week & Weekend or
Individual Days
Mon-Sun Mon-Fri Sat-Sun
Time Temp Time Temp Time Temp
MiStat Rear
Week & Weekend or
Individual Days
Mon-Fri Sat-Sun
Temp Time Temp Time Temp
27/09/2013 09:32