Set Chime Zones; Set Part 2 Zones - Bosch Solution 64 User Manual

Solution 64 | User Guide
Zone 1 Name Z001 is
bypassed. To un-bypass,
press OFF.
Press OK or MENU
If the zone is not bypassed, the keypad will prompt:
Zone 1 Name Z001 is
un-bypassed. To bypass,
press ON.
Press OK or MENU
3. Press [ON] or [OFF] to toggle the zone to be bypassed/un-
bypassed.
4. Press [OK] to save and exit, or press [MENU] to exit without
saving.
Repeat steps 1 to 4 to bypass or un-bypass additional zones.
Inputs > Commands >

Set Chime Zones

This menu allows you to program zones to be monitored when
the system is turned off. Chime mode is ideal to monitor a front
door to sound the keypad buzzer when opened (faulted).
1. Enter [MENU] + [3] + [0] + [3].
A list of areas will display on the keypad.
2. Use the [ ] and [ ] keys to select the area that you want
to program zones for chime mode, then press [OK].
Alternatively, you can enter the area number that you want
to program chime zones, then press [OK].
The keypad will list all zones that can be programmed for
chime mode. A ' ' displayed on the right side of the zone
name indicates that the zone is already set for chime.
Z001 Zone 1 Name
Z002 Zone 2 Name
Z003 Zone 3 Name
Press
3. Use the [ ] and [ ] keys to select the zone that you want to
set for chime, then press [OK]. Alternatively, you can enter
the zone number that you want to set for chime, then press
[OK].
If the zone is not programmed for chime, the keypad will
prompt:
Zone 1 Name Z001
Zone Chime is OFF,
To turn ON, Press ON.
To Go Back Press OK
If the zone is programmed for chime, the keypad will
prompt:
16
MENU 3-0-3
OK or MENU
Zone 1 Name Z001
Zone Chime is ON.
To turn OFF, Press OFF.
To Go Back Press OK
4. Press [ON] or [OFF] to toggle the zone to be monitored
when chime mode is turned on.
5. Press [OK] to save and exit, or press [MENU] to exit without
saving.
Inputs > Commands >

Set Part 2 Zones

This menu allows you to program which zones are to be
monitored when an area has been turned Part 2 On.
1. Enter [MENU] + [3] + [0] + [4].
A list of areas will display on
2. Use the [ ] and [ ] keys to select the area that you want to
program zones for Part 2 On, then press [OK]. Alternatively,
you can enter the area number that you want to program
Part 2 On zones, then press [OK].
The keypad will list all zones that can be programmed for
Part 2 On. A ' ' displayed on the right side of the zone
name indicates that the zone is already bypassed.
Z001 Zone 1 Name
Z002 Zone 2 Name
Z003 Zone 3 Name
Press
3. Use the [ ] and [ ] keys to select the zone that you want to
set for Part 2, then press [OK]. Alternatively, you can enter
the zone number that you want to set for Part 2, then press
[OK].
If the zone is not programmed for Part 2, the keypad will
prompt:
Zone 1 Z001
Is not a PART2 Zone,
To Enable, Press ON.
To Go Back Press OK
If the zone is programmed for Part 2, the keypad will
prompt:
Zone 1 Z001
Is a PART2 Zone,
To remove, Press OFF.
To Go Back Press OK
4. Press [ON] to monitor the zone when the area is turned Part
2 On, or press [OFF] so that you do not monitor the zone
when the area is turned Part 2 On.
5. Press [OK] to save and exit, or press [MENU] to exit without
saving.
MENU 3-0-4
the keypad.
OK or MENU
Bosch Security Systems | 12/05 | BLCC110U