Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Husqvarna HUV 4213-G
Summary of Contents for Husqvarna HUV 4213-G
- Page 1 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Gasoline Utility Vehicles...
- Page 3 Your authorized representative checked the vehicle before it was delivered to you and will provide you a copy of the completed vehicle warranty registration form. Husqvarna is not liable for errors in this manual or for incidental or consequential damages that result from the use of the material in this manual.
-
Page 4: Regular Maintenance Items
We hope you will consider this owner’s manual a permanent part of your Husqvarna vehicle. If you sell the vehicle, please include the manual so that the next owner will have the important operating, safety, and maintenance information it contains. -
Page 5: Table Of Contents
Master Cylinder ... 30 Engine Oil ... 31 Fueling Instructions... 35 Battery ... 36 Cleaning the Vehicle ... 38 Accessories... 38 Subsequent Owner Registration ... 39 Vehicle Specifications ... 40 Warranties... 42 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Page 3... -
Page 6: Safety Decal And Feature Identification
Safety Decal and Feature Identification SAFETY DECAL AND FEATURE IDENTIFICATION The following pages contain safety decal and feature identification information. For detailed information on specific features, read the appropriate section in this manual. Page 4 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... - Page 7 Decal, Rotating Parts Warning (on frame) Safety Decal and Feature Identification 102224301 Decal, Operating Instructions (on steering wheel) Serial Number Fuel Shut-Off Valve Low Oil Warning Light Accelerator Pedal Brake Pedal Fuel Gauge Light Switch 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Page 5...
- Page 8 Decal, Winch Safety Warning (on vehicle body, 102231601 below seat) Decal, Diode Safety Warning (on vehicle frame, 102345901 near diode) Page 6 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Decal, Bed Latch Warning (on vehicle body, below 102459301 bed latch) Forward/Reverse Control Park Brake Choke...
-
Page 9: Practice Safety
PROPOSITION 65 – STATE OF CALIFORNIA WARNING • This product contains or emits chemicals or substances that have been determined by the state of California to cause cancer and birth defects or other reproductive harm. 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Page 7... -
Page 10: Safety Details
• A CAUTION with the safety alert symbol indicates a hazard or unsafe practice that could result in minor personal injury. CAUTION • A CAUTION without the safety alert symbol indicates a potentially hazardous situation that could result in property damage. Page 8 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... -
Page 11: General Warnings
• The vehicle will not provide protection from lightning, flying objects, or other storm-related hazards. If caught in a storm while driving a Husqvarna vehicle, exit the vehicle and seek shelter in accordance with applicable safety guidelines for your location. -
Page 12: Model Identification
The instrument panel must be removed to view this decal. See following NOTE. NOTE: Have the vehicle serial number available when ordering parts or making inquiries. Page 10 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... -
Page 13: Controls And Indicators
• With the differential lock engaged, vehicle turning functions are greatly reduced. To prevent loss of vehicle control when differential lock is engaged, do not operate vehicle at speeds greater than half throttle and use caution when attempting to turn the vehicle. 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Controls and Indicators Page 11... -
Page 14: Key Switch
(NEUTRAL). The engine must be at idle before shifting the Forward/Reverse handle. See preceding WARNING and CAUTION. Husqvarna vehicles operate at a reduced speed in reverse. The reverse buzzer will sound as a warning when the Forward/Reverse handle is in the REVERSE position. -
Page 15: Accelerator Pedal
When the accelerator pedal is released, it will return to the original position and the engine will idle. See preceding WARNING and CAUTION. Figure 6 Accelerator and Brake Pedals Figure 7 Brake Pedal 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Controls and Indicators Page 13... -
Page 16: Brake Pedal
The choke is located on the seat support panel below and to the left of the driver’s left knee. If the vehicle is hard to start in cool or cold temperatures, activate choke: Pull the choke handle out to activate. Release the handle when the engine begins to run smoothly (Figure 9). Page 14 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... -
Page 17: Differential Lock
See following CAUTION. CAUTION • Failure to add oil immediately when the low oil warning light stays on may result in permanent engine damage. Figure 10 Differential Lock 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Controls and Indicators Page 15... -
Page 18: Fuel Gauge/Hour Meter
To engage the seat latch, push down firmly on the seat back until the seat locks into place. See following WARNING. Page 16 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... -
Page 19: Pre-Operation And Daily Safety Checklist
• Make sure seat hinges and latch are securely engaged before operating vehicle. PRE-OPERATION AND DAILY SAFETY CHECKLIST Each Husqvarna vehicle has been thoroughly inspected and adjusted at the factory; however, upon receiving your new vehicle(s), you should become familiar with its controls, indicators, and operation. Carefully inspect each vehicle to ensure that it is in proper working condition before accepting delivery. -
Page 20: Driving Instructions
Driving Instructions Use the following checklist, in conjunction with the Pre-Operation and Daily Safety Checklist, as a guide to inspect the vehicle and check daily for proper operation. Any problems should be corrected by a Husqvarna distributor/dealer or a trained technician. -
Page 21: Starting The Vehicle
Turn the key all the way to the START position and hold, activating the choke as necessary, until the engine has started. The engine will idle with the Forward/Reverse handle in the NEUTRAL position. 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Driving Instructions... -
Page 22: Stopping The Vehicle
Remove the key and turn the fuel shut-off valve to the closed (OFF) position when the vehicle is not in use (Figure 14, Page 25). See also Figure 24 on page 36. Page 20 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... -
Page 23: Bed Latch And Prop Rod
In that event, please refer to the cab installation instructions for the shock absorber adjustment procedure. Figure 13 Prop Rod 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Bed Latch and Prop Rod Page 21... -
Page 24: Loading And Unloading
NOTE: A standard HUV4213 vehicle with a cab accessory weighing 235 lb. (107 kg) must reduce its maximum payload capacity by 235 lb. (107 kg). Page 22 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual HUV4213 800 lb. (363 kg) 1200 lb. -
Page 25: Towing With The Vehicle
• For use on public roads, the trailer must meet all federal, state, and local requirements such as taillights, brake lights, etc. • Never tow a Husqvarna vehicle behind a passenger vehicle or truck on a public road unless it is on an approved trailer. -
Page 26: Storage
6.4. Disconnect fuel vent line from fuel tank vent nipple. 6.5. Plug the fuel tank vent nipple so that it is air tight. We recommend using a slip-on vinyl cap. Page 24 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual ®... -
Page 27: Returning The Stored Vehicle To Service
Raise the cargo bed to access the engine and battery. See WARNING “For vehicles with cargo beds...” in General Warnings on page 9. Lift the front passenger seat. Restore fuel system to operation (Figure 24). 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Storage Page 25... -
Page 28: Maintenance
Any vehicle not functioning correctly should not be used until it is repaired. This will prevent further damage to the vehicle and avoid the possibility of injury due to unsafe conditions. Contact your local Husqvarna dealer for repairs, semiannual and annual periodic service. WARNING •... -
Page 29: Periodic Service Schedule
Periodic Service and Lubrication Schedules. Both the Periodic Service Schedule and the Periodic Lubrication Schedule must be followed to keep vehicle in optimum operating condition. 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Periodic Service Schedule Page 27... - Page 30 (or every 100 hours of operation, whichever comes first) Two year service by trained technician only (or every 200 hours of operation, whichever comes first) Page 28 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual SERVICE Pre-Operation and Daily Safety Checklist Performance Inspection Engine Tires...
-
Page 31: Periodic Lubrication Schedule
LUBRICATION POINTS Figure 15 Lubrication Points 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Periodic Lubrication Schedule RECOMMENDED LUBRICANT Dry Moly Lube (P/N 603 00 00-01) Dry Moly Lube (P/N 603 00 00-01) Chassis Lube (EP NLGI Grade 2) 29 oz. -
Page 32: Master Cylinder
CAUTION • Use only DOT–5 (silicone) brake fluid. Use of any other type brake fluid is not recommended. Page 30 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... -
Page 33: Engine Oil
Turn the key switch to the OFF position, then remove the key. Place the Forward/Reverse handle in the NEUTRAL position. Chock the front wheels. Access the engine compartment. See following WARNING. 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Engine Oil Page 31... - Page 34 This will allow the oil filter more clearance under the electrical component box (Figure 19). Relocate the oil drain pan to a position under the engine oil filter (Figure 20). Page 32 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Figure 18 Engine Oil Drain Plug and Pan...
- Page 35 (Figure 21). This will help seal the filter to the oil filter mounting bracket. See following NOTE. NOTE: Use only Husqvarna oil filters (P/N 603 00 00-06) designed for this engine. 1. Snubber Bracket 2. Snubber 3. Compress Down Figure 19 Compress Snubber Downward ®...
-
Page 36: Oil Viscosity
19. Remove the dip stick and check the engine oil as a final step. Replace the dip stick. OIL VISCOSITY Choose the viscosity according to the temperature as indicated by the oil viscosity chart (Figure 23). Figure 23 Oil Viscosity Chart Page 34 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Figure 22 Add Engine Oil... -
Page 37: Fueling Instructions
Clean any spilled fuel from the tank top and around the tank area. Replace passenger seat. WARNING • Make sure seat hinges and latch are securely engaged before operating vehicle. 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Fueling Instructions Page 35... -
Page 38: Battery
The battery in the vehicle is a 12-volt, low-maintenance battery that requires infrequent checks (Figure 25). Electrolyte level should be checked semiannually. Turn the key switch to the OFF position and remove the key. Place the Forward/Reverse handle in the NEUTRAL position. Chock the wheels. Page 36 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual... - Page 39 (do not leave discharged overnight). 1. Level Indicator 2. Cap 3. Plates Electrolyte level at least 1/2 inch (13 MM) above plates or to level indicator. Figure 26 Battery Electrolyte Level 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Battery Page 37...
-
Page 40: Cleaning The Vehicle
See Safety Decal and Feature Identification on page 4. The winch kit available from Husqvarna includes a remote operation switch, which enables the operator to move away from the vehicle and cable. See following WARNING and CAUTION. -
Page 41: Subsequent Owner Registration
In the event a vehicle is bought as a used vehicle, we strongly urge the new owner to register the vehicle with Husqvarna. This will enable us to contact you if the need arises. Please send your name, address, and serial number of the vehicle to Husqvarna, 7349 Statesville Rd., Charlotte, NC 28269, Attention: Vehicle Registration. -
Page 42: Vehicle Specifications
Front wheel tread Rear wheel tread Weight (dry): with all-terrain tread with turf tread Forward speed Governed RPM: FE400 Engine Page 40 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual HUV4213-GXP HUV4213-G • • • • •... -
Page 43: Specifications
Fuel tank TIRE PRESSURE All-terrain tread (standard) Turf tread (optional) Traks Max II tread (optional) HUV4213-GXP 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Vehicle Specifications HUV4213-G 24 ft. 1 in. (734 cm) 139.6 in. (355 cm) 112.2 in (285 cm) 17 in. -
Page 44: Warranties
Portable Refreshment Center, and all other original equipment options and accessories supplied by Husqvarna are warranted with respect to parts and labor against defects in material and workmanship for a period of one year or 1000 hours of operation, whichever first occurs, from the date of purchase. -
Page 45: How To Make A Warranty Claim
REPAIR OF THE DEFECTIVE VEHICLE OR COMPONENT THEREOF IS THE SOLE REMEDY OF THE PURCHASER. HUSQVARNA MAKES NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, AND NO REPRESENTATIVE, EMPLOYEE, OR DEALER OF HUSQVARNA HAS THE AUTHORITY TO MAKE OR IMPLY ANY REPRESENTATION, PROMISE OR AGREEMENT, WHICH IN ANY WAY VARIES THE TERMS OF THIS WARRANTY. -
Page 46: California Emission Control Warranty Statement
- As the vehicle engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. Husqvarna recommends that you retain all receipts covering maintenance on your vehicle engine, but Husqvarna cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. - Page 47 Husqvarna will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part. *Husqvarna, its authorized dealers, or a service agency approved by Husqvarna.
-
Page 48: No Consequential Damages
5. NO CONSEQUENTIAL DAMAGES: In no event shall Husqvarna be liable for any incidental or consequential damages including, but not limited to, loss related to property other than the vehicle, loss of use, loss of time, inconvenience, or any other economic loss. This warranty is applicable only where the California or U.S. - Page 52 Publication Part Number 603 00 43-23 Edition Code 0707C0608B...
Need help?
Do you have a question about the HUV 4213-G and is the answer not in the manual?
Questions and answers