Installing an adapter in a server ........................9 Installing a low profile bracket ........................9 Specifications ..........................10 HP NC375T PCI Express Quad Port Gigabit Server Adapter specifications............. 10 UTP cable specifications........................... 11 Regulatory compliance notices ..................... 12 Regulatory compliance identification numbers ..................... 12 Federal Communications Commission notice....................
Technician notes WARNING: Only authorized technicians trained by HP should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module-level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board.
Type the adapter name in the For product box and then click Go. For example, type NC375T. Download the drivers, firmware, or documentation as needed. HP contact information For the name of the nearest HP authorized reseller: • See the Contact HP worldwide (in English) webpage (http://welcome.hp.com/country/us/en/wwcontact.html).
For the latest functionality, features, and operating system support for this adapter, see the HP website (http://h18004.www1.hp.com/products/servers/networking/index-nic.html). UTP CAT5 cable The NC375T adapter can use existing UTP CAT5 (or better) cable to deliver Gigabit Ethernet over copper, according to the IEEE 802.3ab specifications. For new installations, CAT5e (enhanced CAT5) cable is recommended.
LED indicators The NC375T adapter has four auto-negotiating 10/100/1000 RJ-45 ports. LED indicators show activity, link, and port speed. Standard-height and low-profile brackets with RJ-45 ports and LED indicators are shown below. The LED indicators operate as described in the following table.
NOTE: Before removing the cover of your server, refer to the HP documentation for the proper methods for installing a PCI Express card and avoiding electric shock hazards.
Installing an adapter in a server The NC375T can be installed in either a standard or low-profile PCI Express slot. The kit includes brackets for both slot types. See the HP ProLiant server documentation for additional information on how to safely install a PCI Express card in the server.
Specifications HP NC375T PCI Express Quad Port Gigabit Server Adapter specifications Specification Value Network controller chipsets Netxen NX3031 Bus type x4 PCI-Express v2.0 & v1.1 Bus width Four lanes On-board memory 128MB for PCA Data transfer method Bus Master DMA...
UTP cable specifications The NC375T adapter can use existing UTP CAT5 (or better) cable to deliver Gigabit Ethernet over copper, according to the IEEE 802.3ab specifications. For new installations, CAT5e (enhanced CAT5) cable is recommended. Maximum distances for Gigabit over copper cable are 100 meters (328 feet).
Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number.
Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 • 1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded or monitored.) For questions regarding this FCC declaration, contact us by mail or telephone: • Hewlett-Packard Company P.
*Notified body number (used only if applicable—refer to the product label) Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany The official EU CE declaration of conformity for this device can be found on the HP website (http://www.hp.com/go/certificates). Japanese class B notice...
Page 15
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices.
Acronyms and abbreviations ACPI Advanced Configuration and Power Interface alert standard forum Canadian Standards Association direct memory access IEEE Institute of Electrical and Electronics Engineers light-emitting diode printed circuit assembly PCI Express Peripheral Component Interconnect Express Preboot Execution Environment Quality of Service RoHS Restriction of Hazardous Substances unshielded twisted pair...
Page 18
VLAN virtual local-area network Acronyms and abbreviations 18...
Need help?
Do you have a question about the NC375T and is the answer not in the manual?
Questions and answers