Duratrax Evader bx Pro Owner's Manual
Duratrax Evader bx Pro Owner's Manual

Duratrax Evader bx Pro Owner's Manual

Evader bx pro ready to run
Hide thumbs Also See for Evader bx Pro:

Advertisement

Quick Links

Length: 15.5" [394mm]
Width: 9-7/8" [251mm]
Height: 6.5" [165mm]
Weight: 44 oz. [1247g] without battery
Wheelbase: 11.6" [295mm]
Radio: Futaba
®
2PL Computer Radio
Motor: 15 Turn Team Orion
• DuraTrax
®
will warranty this kit for 90 days after the purchase date from defects in materials or workmanship. DuraTrax
will either repair or replace, at no charge, the incorrectly made part. Exception: Specific parts covered under the
Graphite Parts and Stress Tech
• Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase
and we must see it before we can honor the warranty.
• To return your Evader BX Pro for repairs covered under warranty you should send your buggy to:
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to
return this kit immediately in new and unused condition to the place of purchase.
READ THROUGH THIS MANUAL BEFORE STARTING. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS
CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.
v1.0 © Copyright 2003
READ
READ
®
Havok
ASSEMBLY AND OPERATION MANUAL
Guarantee, see page 3.
3002 N. Apollo Drive Suite 1
Champaign, Illinois 61822
Attn: Service Department
Phone: (217) 398-0007 9:00 am-5:00 pm Central Time M-F
E-mail: hobbyservices@hobbico.com
®
Y-T
O-R
UN
Y-T
O-R
UN
Warranty
Hobby Services
Technical Support Information
For technical assistance, contact:
DuraTrax Product Support
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
(217) 398-8970, Ext. 5
carsupport@duratrax.com
DTXZ3102 For Kit DTXD28**

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Evader bx Pro and is the answer not in the manual?

Questions and answers

Summary of Contents for Duratrax Evader bx Pro

  • Page 1 • Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase and we must see it before we can honor the warranty. • To return your Evader BX Pro for repairs covered under warranty you should send your buggy to: Hobby Services 3002 N.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION INTRODUCTION ..............2 Thank you for purchasing the DuraTrax Evader BX Pro. This IMPORTANT SAFETY PRECAUTIONS ......2 manual contains the instructions you need to build, operate HELPFUL HINTS ...............2 and maintain your new electric R/C vehicle. Read over this GRAPHITE &...
  • Page 3: Graphite & Stress Tech Parts Guarantee

    PARTS GUARANTEE All pictures, descriptions and specifications found in this We have engineered the Evader BX Pro to take the rough and instruction manual are subject to change without notice. tumble abuse that makes R/C fun. We are so confident of the...
  • Page 4: Finishing

    FINISHING 1. Remove the Evader BX Pro and radio system from the box. Route the antenna 2. Charge the 6- or 7-cell battery (not included) on the through the chassis charger (not included). See Safety Precautions before and then through the tube.
  • Page 5: Intellispeed Set Up

    8. Install the charged 6 or 7 cell battery into the battery slot (remove foam if using a 7-cell). Re-install the battery strap onto the Evader BX Pro. Note that there is a channel in the chassis for the battery strap to rest in. Re-install the body The following instructions will help you get trouble-free clip into the battery strap post.
  • Page 6: Speed Control Cautions

    Speed Control Cautions Acceleration / Traction Control • Do not run the car near water! Never allow water, moisture, The acceleration, or traction control function provides 3 or any foreign material inside the case of the ESC. optional time delays which control how quickly full forward speed is delivered to the motor after full deflection is given to •...
  • Page 7: Thermal Cutoff Protection

    ESC WORKS BUT OTHER PROBLEMS EXIST B. After two seconds, the green and red LED will blink TWICE. Press and release the pushbutton at this time to set a delay of 0.8 seconds. Problem: Rx glitches or stutters during acceleration. 1) The three required motor capacitors are not installed or C.
  • Page 8: Ball Differential Break-In

    Evader BX Pro. differential is properly broken-in and now requires Running of the Evader BX Pro with broken or damaged parts adjustment. Do not run the buggy again until the differential could result in damage to other parts.
  • Page 9: Assembly Guide

    ASSEMBLY GUIDE The following information has been provided to help maintain and tune the Evader BX Pro. Front Knuckle Arm, Hub Carrier, Axle 1. Attach the front hub carriers (28) to the front suspension arms (38) using the (95) front outer hinge pins.
  • Page 10: Servo, Servo Plate, Upper Plate

    Servo, Servo Plate, Upper Plate 1. Attach the servo mounting lugs (6) to the front of the servo mounts on the servo using two 3x8 self tapping screws (L). 2. Install a ball stud (81) into the steering servo horn (8). Insert the ball stud into the hole furthest from the center.
  • Page 11: Ball Differential

    Bulkhead, Bulkhead Brace, Front Suspension Arm, Front Shock Tower, Front Bumper 1. Attach the front bulkhead to the chassis using the (103) hinge pin. 2. Secure the hinge pin in place using a 2mm set screw. 3. Attach and secure the front suspension arms (38) to the front bulkhead (51) using the (104) front inner hinge pins.
  • Page 12: Slipper Clutch

    Slipper Clutch 1. Install the inner slipper plate (86) onto the top shaft (83). Make sure the notch in the inner slipper plate keys onto the 2x10 spring pin in the top shaft. 2. Place the slipper pad (64) and outer slipper plate (85) onto the top shaft (83). Make sure the slipper pad (64) is properly centered between the two plates (85 &...
  • Page 13: Gearbox

    Gearbox Note: When installing the bearings, make sure they are fully seated. If the bearings are not fully seated the gearbox halves may not properly fit together or may cause binding. 1. Install a 5mm washer (X) onto each end of the top shaft (83) 2.
  • Page 14: Shocks

    76 (Rear) 75 (Front) 78 (Rear) 71 (Rear) 77 (Front) 70 (Front) 2. Slowly screw the cap down about half way. Push the piston part way down to slowly bleed off excess oil. 3. Tighten the cap a little 1. Fill to the top more and push the piston with oil.
  • Page 15: Tuning Guide

    Toe-out will increase steering into corners, but will decrease the overall stability during acceleration. The When tuning the Evader BX Pro make sure that you have front typically is set-up with 0 to -2 degrees of toe-in.
  • Page 16: Battery Placement

    RIDE HEIGHT which is a good choice for most driving conditions. The ride height of the Evader BX Pro affects how it jumps and handles. The ride height of the Evader BX Pro is adjustable through the threaded pre-load adjusters on the shock bodies.

Table of Contents