Samsung SCX-812x Series User Manual page 149

Message Meaning
Right door is open. The door is not
Close it. securely latched.
Scanner locked or The CCD (Charged
another problem Couple Device) lock
occurred. has been locked.
Scan System There is a problem in
Failure [error the scan system.
number]:Turn off
then on.
Second fax modem The second optional
card is not fax multiline kit is not
installed. Install installed.
the card.
Shake [color] toner Small amount of toner
cartridge. is left in the indicated
cartridge.
Side feeder door is The door is not
open. Close it. securely latched.
Staple cartridge is The staple cartridge
empty. Replace it. has reached the end
of its lifespan.
Staple cartridge is Small amount of
low. Replace staple cartridge is left.
cartridge. The estimated life of
staple cartridge is
close.
Staple cartridge is The staple cartridge is
not installed. not installed or the
Install it in finisher. staple cartridge is not
properly installed.
Staple cartridge of The staple cartridge of
booklet I is empty. booklet has reached
Replace cartridge. the end of its lifespan.
Staple cartridge of Small amount of
booklet I is low. staple cartridge of
Replace cartridge. booklet is left. The
estimated life of staple
cartridge is close.
Suggested solutions
Close the door until it
locks into place.
Unlock the CCD lock . Or
turn the machine off and
back on again. If the
problem persists, call for
service. Scanner
Turn the machine off and
back on again. If the
problem persists, call for
service.
Install the optional fax
multiline kit. If it is already
installed, try to reinstall
the optional fax multiline
kit. If the problem
persists, call for service.
You may temporarily
increase the printing
quality by redistributing
the toner (see
"Redistributing toner" on
page 125).
Close the door until it
locks into place.
This message appears
when the staple cartridge
is completely empty.
Replace the staple
cartridge.
Prepare a new staple
cartridge for a
replacement.
Install the staple
cartridge. If it is already
installed, try to reinstall
the staple cartridge. If the
problem persists, call for
service.
This message appears
when the staple cartridge
is completely empty.
Replace the staple
cartridge.
Prepare a new staple
cartridge for a
replacement.
Troubleshooting_ 149
Message Meaning
Staple cartridge of The staple cartridge of
booklet I is not booklet is not installed
installed. Install or the staple cartridge
the cartridge. is not properly
installed.
The clock became The time setting of
initial time. Set a machine is initialized.
time again.
Too much media in The center tray is full.
the center tray.
Remove printed
media.
Too much media in The booklet tray is full.
booklet tray.
Remove printed
media.
Too much media in The finishing tray is
finisher tray. full.
Remove printed
media.
Top door of
The duplex automatic
scanner is open.
document feeder
cover is not securely
latched.
Transfer belt The transfer belt
cleaning unit is not cleaning unit is not
installed. Install it. installed.
Transfer belt is not The transfer belt is not
installed. Install it. installed.
Transfer belt The life of the transfer
cleaning unit is belt cleaning unit
worn. Replace with expires totally.
new one.
Transfer belt unit The life of the transfer
is worn. Replace it. belt unit expires
totally.
[tray number] The tray is not
cassette is pulled securely latched.
out. Insert it
properly.
[tray number] door The tray is not
is open. Close it. securely latched.
UI System Failure There is a problem in
[error the UI system.
number]:Turn off
then on.
Suggested solutions
Install the staple
cartridge. If it is already
installed, try to reinstall
the staple cartridge. If the
problem persists, call for
service.
Set the time setting in
Machine Setup.
Remove printouts from
the center tray, the
machine resumes
printing.
Remove printouts from
the booklet tray, the
machine resumes
printing.
Remove printouts from
the finishing tray, the
machine resumes
printing.
Close the cover until it
locks into place.
Power off/on, if the
problem persists, call for
service.
Power off/on, if the
problem persists, call for
service.
Replace the transfer belt
cleaning unit with a
Samsung-genuine
transfer belt cleaning
unit, call for service.
Replace the transfer belt
unit with a
Samsung-genuine
transfer belt unit, call for
service.
Close the tray until it
locks into place.
Close the tray until it
locks into place.
Turn the machine off and
back on again. If the
problem persists, call for
service.