Checklist - Kenmore N8MSL0701412A1 Installation Instructions Manual

a. Verify vent pipe is cool to the touch.
b. Disconnect power to furnace and remove vent con-
nector from furnace vent elbow.
c. Restore power to furnace and set room thermostat
above room temperature.
d. After normal start-up, allow furnace to operate for 2
minutes, then block vent elbow in furnace 80 per-
cent of vent area with a piece of flat sheet metal.
e. Furnace should cycle off within 2 minutes. If gas
does not shut off within 2 minutes, determine reas-
on draft safeguard switch did not function properly
and correct condition.
f. Remove blockage from furnace vent elbow.
g. Switch will auto-reset when it cools.
h. Re-install vent connector.
NOTE: Should switch remain open longer than 3 minutes,
furnace control board will lockout the furnace for 3 hrs. To
reset furnace control board, turn thermostat below room
temperature or from HEAT to OFF and turn 115-v power
OFF, then back ON.
3. Check Pressure Switch This control proves operation
of the draft inducer blower.
a. Turn off 115-v power to furnace.
b. Disconnect inducer motor lead wires from wire har-
ness.
c. Turn on 115-v power to furnace.
d. Set thermostat to "call for heat" and wait 1 minute.
When pressure switch is functioning properly, hot
surface igniter should NOT glow and control dia-
gnostic light flashes a status code 3. If hot surface
igniter glows when inducer motor is disconnected,
shut down furnace immediately.
e. Determine reason pressure switch did not function
properly and correct condition.
f. Turn off 115-v power to furnace.
g. Reconnect inducer motor wires, replace outer door,
and turn on 115-v power.
h. Blower will run for 90 sec and flash status code 1+2
before beginning the call for heat again.
i. Furnace should ignite normally.
Step 5--Checklist
1. Put away tools and instruments. Clean up debris.
2. Verify that heat off-delay time is selected as desired.
3. Verify that blower and burner access doors are prop-
erly installed.
4. Cycle test furnace with room thermostat.
5. Check operation of accessories per manufacturer's in-
structions.
6. Review User's Guide with owner.
7. Attach literature packet to furnace.
SECONDS FOR 1
REVOLUTION
Table 13--Gas Rate (cu ft./hr)
SIZE OF TEST DIAL
Cu Ft 2 Cu Ft 5 Cu Ft
SECONDS FOR 1
REVOLUTION 1 Cu Ft
10 360 720 1800 50 72
11 327 655 1636 51 71
12 300 600 1500 52 69
13 277 555 1385 53 68
14 257 514 1286 54 67
15 240 480 1200 55 65
16 225 450 1125 56 64
17 212 424 1059 57 63
18 200 400 1000 58 62
19 189 379 947 59 61
20 180 360 900 60 60
21 171 343 857 62 58
22 164 327 818 64 56
23 157 313 783 66 54
24 150 300 750 68 53
25 144 288 720 70 51
26 138 277 692 72 50
27 133 267 667 74 48
28 129 257 643 76 47
29 124 248 621 78 46
30 120 240 600 80 45
31 116 232 581 82 44
32 113 225 563 84 43
33 109 218 545 86 42
34 106 212 529 88 41
35 103 206 514 90 40
36 100 200 500 92 39
37 97 195 486 94 38
38 95 189 474 96 38
39 92 185 462 98 37
40 90 180 450 100 36
41 88 176 439 102 35
42 86 172 429 104 35
43 84 167 419 106 34
44 82 164 409 108 33
45 80 160 400 110 33
46 78 157 391 112 32
47 76 153 383 116 31
48 75 150 375 120 30
49 73 147 367
SIZE OF TEST DIAL
2 Cu Ft 5 Cu Ft
144 360
14t 355
138 346
136 340
133 333
131 327
129 321
126 316
124 310
122 305
120 300
116 290
112 281
109 273
106 265
103 257
100 250
97 243
95 237
92 231
90 225
88 220
86 214
84 209
82 205
80 200
78 196
76 192
75 188
74 184
72 180
71 178
69 173
68 170
67 167
65 164
64 161
62 155
60 150
34 441 01 1402 02