Page 3
Preface Fujitsu would like to thank you for purchasing our ETERNUS DX80 S2/DX90 S2 Disk storage system. The ETERNUS DX80 S2/DX90 S2 Disk storage system is designed to be connected to a Fujitsu (PRIMEQUEST or PRIMERGY) or non-Fujitsu servers. This manual describes operation management and maintenance for the ETERNUS DX80 S2/DX90 S2 Disk storage system.
This chapter describes the components of the ETERNUS DX80 S2/DX90 S2 Disk storage system. ● Chapter 2 Basic Operation This chapter explains how to turn on and off the ETERNUS DX80 S2/DX90 S2 Disk storage system and how to operate the FUNCTION button on the controller enclosure. ●...
Page 5
ETERNUS DX Disk storage system and/or to other users CAUTION and their property, if the ETERNUS DX80 S2/DX90 S2 Disk storage system is not used properly. This symbol indicates IMPORTANT information for the user to note when using the ETERNUS DX80 S2/DX90 S2 Disk storage system.
Abbreviations Used in This Manual • "ETERNUS DX Disk storage system" refers to the DX80 S2/DX90 S2 Disk storage system. • "CA" refers to a host interface module that is used in an ETERNUS DX Disk storage system to connect to a server.
Page 9
A.2.5 Test Messages ............................. 149 A.2.6 Sense Codes..............................149 Appendix B Audit Log List Appendix C Event (SNMP Trap) Display When Using ServerView Operation Manager ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 10
Figure 1.27 Power supply unit............................28 Figure 1.28 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 1U, Max 2 enclosures connection) ....29 Figure 1.29 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U, Max 6 enclosures connection) ....30 Figure 1.30...
Page 11
Table 6.1 Time for volume formatting (disk) ......................93 Table 6.2 Rebuild process time (disk) ......................... 94 Table 6.3 Copyback process time (disk) ........................94 ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
3.5" type Figure 1.2 Front view of a 3.5" type controller enclosure Operation panel 3.5" disk or 3.5" Solid State Drive (SSD) Flange cover Flange cover ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
■ Dual-controller type Figure 1.4 Rear view of a controller enclosure (dual-controller type) Controller (CM#0) Controller (CM#1) Power supply unit (PSU#0) Power supply unit (PSU#1) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Figure 1.6 Operation panel (3.5" type controller enclosure) With a flange cover Without a flange cover POWER LED READY LED FAULT LED FUNCTION button MAINT/ID LED CACHE LED Power switch ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Maintenance or a status check via ETERNUS Web GUI or ETERNUS CLI is necessary. CACHE There is data in the ETERNUS DX Disk storage system cache memory. (green) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
CA#1 FAULT LED UNIT ID LED MASTER LED LAN (MNT) port PWC port LINK/FAULT LEDs ACT LEDs LINK LEDs Host interface (CA#0) Host interface (CA#1) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The controller is sending or receiving data via the LAN port (for operation management). (green) LINK The link between the LAN port (for operation management) and the destination has been established. (green) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Host interface ports (FC, iSCSI 10Gbit/s, FCoE (for FC cable connection)) (from left to right: Port#0 and Port#1 in CA#0, Port#0 and Port#1 in CA#1) These are the Dual LC connectors to connect FC cables. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Host interface ports (iSCSI) (from left to right: Port#0 and Port#1 in CA#0, Port#0 and Port#1 in CA#1) These are the RJ-45 connectors to connect LAN cables. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Each power supply unit contains fans. Figure 1.16 Power supply unit Inlet POWER LED PSU switch PSU FAIL LED AC MISSING LED FAN FAIL LED ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The power supply unit or the fan in the power supply unit is in error status. (off) (amber) (amber) (amber) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Figure 1.18 Front view of a 3.5" type drive enclosure 3.5" disk or 3.5" Solid State Drive (SSD) DE-ID (drive enclosure number) display panel Flange cover Flange cover ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
This section describes LEDs, a DE-ID (drive enclosure number) display panel, and drives of the front of the drive enclosure. ■ DE-ID (drive enclosure number) display panel The DE-ID (drive enclosure number) of the drive enclosure is displayed. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The drive enclosure is in error status. (amber) POWER The drive enclosure is operating normally. (green) ■ Drives ● 2.5" drives Figure 1.22 2.5" drive DRIVE READY LED DRIVE FAULT LED ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
DRIVE FAULT • The drive is in error status. (amber) • In response to commands from ETERNUS CLI, the location of the drive is identified. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The link between the DI (OUT) port and the destination port has been established. (green) DI (IN) LINKUP The link between the DI (IN) port and the source port has been established. (green) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The power supply unit or the fan in the power supply unit is in error status. (off) (amber) (amber) (amber) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The 1U power distribution unit has four outlets and two inlets. ■ Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 1U, Max 2 enclosures connection) Figure 1.28 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 1U, Max 2 enclosures connection) Main line switches Outlets (OUTPUT) Inlets (INPUT) ●...
■ Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U, Max 6 enclosures connection) There are 12 outlets. Figure 1.29 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U, Max 6 enclosures connection) Main line switches Outlets (OUTPUT) ● Part explanation •...
■ Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U, Max 8 enclosures connection) There are 16 outlets. Figure 1.30 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U, Max 8 enclosures connection) Main line switches Outlets (OUTPUT) ● Part explanation •...
For 1U power distribution unit Figure 2.1 ON position (marked "|") of the main line switches on a 1U power distribution unit Main line switch ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
For 1U power distribution unit Figure 2.3 OFF position (marked "O") of the main line switches on a 1U power distribution unit Main line switch ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
When turning the main line switch to ON (marked "I") right after turning the main line switch to OFF (marked "O"), turn it back to ON (marked "I") after the POWER LED of the power supply unit has turned off completely. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
For the drive enclosure, the POWER LED on the power supply unit and the LINE LED on the front emit green lights and the fan revolves at high speed for 30 seconds. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Use the power synchronized unit to turn on the ETERNUS DX Disk storage system. • Via the Wake On LAN function Use the Wake On LAN function to turn on the power. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 37
Press the Power switch of the controller enclosure. Drive enclosure Power switch Drive enclosure Controller enclosure The POWER LEDs on the controller enclosure and the drive enclosures are turned on. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
This section explains how to use the Power switch to turn off the ETERNUS DX Disk storage system. For other procedures, refer to the related manuals. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
The single-controller type only has a "Master CM" controller. • Restoring the factory default settings (network environment settings and firewall settings) of the LAN ports ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 40
Use the pin to push down the FUNCTION button for three seconds. The ETERNUS DX Disk storage system is not in maintenance status when the MAINT/ID LED is off. Attach the flange cover. End of procedure ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
License in the ETERNUS DX Disk storage system. For details on how to register the license, refer to the "Feature activation licenses" document that is provided with the Thin Provisioning Feature License. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The restrictions and points to note when using the Thin Provisioning function are as follows: • Storage capacity virtualization The maximum number of Thin Provisioning Pools (TPP) is 60 for the ETERNUS DX80 S2 and 120 for the ETERNUS DX90 S2. The maximum TPP capacity is 128TB.
Page 43
Zero Reclamation Zero Reclamation cannot be performed for volumes that are undergoing RAID Migration. Zero Reclamation cannot be performed for volumes that are undergoing TPV balancing. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
License in the ETERNUS DX Disk storage system. For details on how to register the license, refer to the "Feature activation licenses" document that is provided with the Thin Provisioning Feature License. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
ETERNUS Web GUI or ETERNUS CLI. Make sure to add drives to expand the FTSP capacity by using ETERNUS SF Storage Cruiser before insufficient FTRP capacity is detected. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Page 46
FTRP balancing may not be performed regardless of what FTRP balancing level is used. FTRP balancing availability depends on the physical allocation status of FTVs. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
When deletion of the migration paths is complete, change the FC port mode from "Initiator" to "CA" and set the port parameters. Set the host affinity setting to recognize migration destination volumes from the server. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
SEDs that are installed in the ETERNUS DX Disk storage system. The common key cannot be changed or deleted after being set. The common key is used to authenticate RAID groups when key management server linkage is not used. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 49
Flexible Tier Volumes (FTVs) cannot be encrypted individually. Rather, the encryption status of TPVs depends on that of the Flexible Tier Pool (FTRP) to which the FTVs belong. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Rebuilding and performing copy back (when using Global Hot Spares) Performing a redundant copy (when using Global Hot Spares) Turning on the disk motor with the Eco-mode ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
For RAID groups in the following conditions, the Eco-mode schedule can be set but the drive motors cannot be stopped: SDPVs are registered ODX Buffer volumes are registered ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 52
To prevent this from occurring, the RAID configuration and drive installation must be taken into consideration. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Striping for multiple RAID groups • Wide Striping Distributing a single volume to multiple RAID groups makes I/O access from the server more efficient and improves the performance. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The final volume number (LUN) will be the same as the initial volume number, and from the point of view of the server, pre-migration, migrating and post-migration volumes are accessed indistinguishably. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
• If the power is turned off or an electrical power outage occurs during LDE, the process will simply continue when the power is restored. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
It is possible to add extra volumes to an already concatenated volume. • After concatenation, any number of formatting processes can be started at once. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
WSVs can be created by RAID groups when the stripe size is specified during WSV creation. Note that WSVs cannot be configured by concatenating RAID groups with different stripe sizes. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
If the Master CM is switched, the same IP addresses are reused. Therefore, even if the Master CM is switched and the physical port is changed, access can be maintained via the same IP addresses. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
The IP address of the Slave CM is used to switch the Master CM and display ETERNUS DX Disk storage system the status of the ETERNUS DX Disk storage system. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The status of the ETERNUS DX Disk storage system can be checked by the LEDs. If the FAULT LED in front of the ETERNUS DX Disk storage system is amber, contact your maintenance engineer. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The ETERNUS DX Disk storage system is under maintenance. Maintenance (Orange) The ETERNUS DX Disk storage system is in warning state. Warning (Yellow) Refer to "ETERNUS Web GUI User’s Guide" for details. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
When an event occurs in the ETERNUS DX Disk storage system, host senses (sense codes) are sent to the server. For details on sense codes, refer to "Appendix A Event Notification Message List" (page 103). ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Login User/Role ↓ Change settings Operation time ↓ Operation details Logout Operation result etc. Audit log System administrator ETERNUS DX Disk storage system Syslog server ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Do not uninstall or move a drive that is already installed. Contact your sales representative or maintenance engineer if a drive needs to be uninstalled or moved. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Failure to discharge static electricity may cause device failure. • Leave the drive in its package until ready to install it. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
ETERNUS DX Disk storage system are in normal status. Wear a wrist strap or touch a metal part to discharge the human body’s natural static electricity. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 68
Lock lever Insert the drive all the way into in the slot, making sure that it is firmly seated and keeping the lock lever open. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 69
ETERNUS DX Disk storage system are in normal status. Wear a wrist strap or touch a metal part to discharge the human body’s natural static electricity. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 70
Insert the drive all the way into in the slot, making sure that it is firmly seated and keeping the lock lever open. WARNING • Hold the drive with both hands to protect against jarring. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 71
In the [Disks] screen of [Component] on the ETERNUS Web GUI screen, check that the added drives are recognized. Set up RAID groups, volumes, hot spares, and Host Affinity settings on the new drives, as required. End of procedure ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
To avoid this, allow the packed drive enclosure sufficient time in the warmer place (one hour for each 15°C of temperature difference) to adapt to the new temperature. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
ETERNUS DX Disk storage system are in normal status. In addition, check the DE-IDs (drive enclosure numbers) of the installed enclosures in the [Drive Enclosure] screen. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 74
A screen to show how to install the drive enclosure appears. Wear a wrist strap or touch a metal part to discharge the human body’s natural static electricity. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 75
M5 Centering screw (10mm) M5 Cage nut M5 Pan head screw (10mm) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 76
(for left side). (Front rack pillars) Rack rail (for right side) "R" is stamped on the inner side of the rack rail (for right side). [Right] ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 77
(M5 screw) (M5 screw) Base line of drive enclosure Rack rails Tighten the M4 screws of the rack rails that were slightly unscrewed in Step (1). ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 78
Fasten the drive enclosure in the rack. ■ For the EMEA&I region Use two M5 screws to fasten it in the rack pillar. M5 screw M5 screw ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 79
Right front side of the drive enclosure Upper rear side of the drive enclosure DE_No. label The DE_No. labels are supplied with the ETERNUS DX Disk storage system. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 80
Attachment location of the bracket Left Right 2.5" type 3.5" type 3.5" type 2.5" type drive enclosure drive enclosure drive enclosure drive enclosure Bracket Thumb screw ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 81
When connecting QSFP cables, check the connector orientation and then firmly push it all the way When disconnecting QSFP cables, use the pull-tab to extract the connector. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Page 82
The following figure shows an example of attaching destination labels on the QSFP cables that connect the controller enclosure to drive enclosure 1. Drive enclosure 1 (Added drive enclosure) Controller enclosure ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 83
Each enclosure has two power supply units (PSU#0 and PSU#1). The power cords must be connected to the inlets of both power supply units. Connect the power cord plugs to the inlets of the power supply units. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 84
For details on drive installation, refer to "5.1.4 Additional Drive Installation Procedure" (page 67). If a wrist strap is used, remove the wrist strap. End of procedure ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
• Contact your maintenance engineer when a host interface is installed in the host interface 1 (CA#1) of the ETERNUS DX80 S2/DX90 S2. 5.3.1 Installation Rules for Host Interfaces This section explains the installation rules for host interfaces.
Failure to discharge static electricity may cause device failure. • Leave the host interface in its package until ready to install it. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Short wave SFP+ modules (16Gbit/s) and Long wave SFP+ modules (16Gbit/s) can be mixed in the same host interface (FC 16Gbit/s). For the dual controller type, the SFP+ module configurations for controller 0 (CM#0) and controller 1 (CM#1) must be the same. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
• Do not place any objects on top of SFP+ modules. • Do not knock or drop SFP+ modules on hard objects. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Push the tab on the FC cable connector and pull out the cable. Make sure to record the connecting port for the disconnected FC cable. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 90
Remove the connector cover that is attached to the Long wave SFP+ module (16Gbit/s) port and pull down the lever. Keep the removed connector cover in a safe place where they will not be lost. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 91
Repeat Step 5 through Step 8 to replace multiple SFP+ modules (FC 16Gbit/s). ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 92
FC port status is Normal and the SFP type is changed to "16G SFP+(SMF)". In addition, confirm that all of the other components are in normal status. End of procedure ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
The value shows the time required for volume formatting when the volume capacity is 100GB and there is no server I/O. The time that is required depends on the type and configuration of the disk. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
The value shows the copyback process time when the volume capacity is 100GB and there is no server I/O. The time that is required depends on the type and configuration of the disk. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
If a possible error that may occur is detected or an error occurs when remote support service is used, the contents of events are automatically sent to the remote support center and notified to the user. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Has there been a recent main power failure? If the Power Resume function is enabled, the ETERNUS DX Disk storage system turns on automatically after the power is restored. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 97
Connect the QSFP cable while the drive enclosure is on. Press the controller enclosure’s Power switch to turn on the ETERNUS DX Disk storage system. End of procedure ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 98
In the details screen for each component, check the detailed information for each component with a contact your maintenance engineer. When checking the general status via ETERNUS CLI, refer to "ETERNUS CLI User’s Guide". ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 99
Use the pin that is provided with the ETERNUS DX Disk storage system to push down the FUNCTION button for three seconds. The ETERNUS DX Disk storage system is in maintenance status when the MAINT/ID LED is green. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 100
Click the icon of each part on the [Storage] screen of [Component] of ETERNUS Web GUI to check if an abnormality is detected in ETERNUS DX Disk storage system parts. If an abnormality is detected, contact your maintenance engineer. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 101
Check if an error occurs in a path by using a path management tool such as ETERNUS Multipath Manager. Refer to the relevant manuals and take the required actions. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
ETERNUS Web GUI. Refer to "ETERNUS Web GUI User’s Guide" for how to obtain this information. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 104
: The year is display with four digits. The detailed information of the event is displayed. For multiple process results, each process result is displayed on a separate line. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
6: Informational For the "RFC3164" format, the HEADER part follows the PRI part. For the "RFC5424" format, "1" and then a blank follow the PRI part. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 106
For the "RFC3164" format, a comma and then a blank follow this item. For the "RFC5424" format, a blank, a hyphen, and a blank follow this item in this order. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
For an ETERNUS DX Disk storage system, this Trap is sent when the controller starts up or restarts and when SNMP is set. authentictionFailure An unauthorized access occurred. enterpriseSepecific Extended Trap ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 108
[2]:snmpTrapOID coldStart The operation time of the SNMP 1.3.6.1.6.3.1.1.5.1 Agent (centiseconds) The operation time is reset when authenticationFailure 1.3.6.1.6.3.1.1.5.5 the SNMP Agent starts or restarts. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 109
TRAP No. 5 Information [3]:fjdaryTrapMessage Information [4]:fjdaryTrapWarningInfo fjdarye100 Notification of Information [1]:fjdaryTrapItemId SensorStatus alarm cancel Information [2]:fjdarySspMachineId ChangeTo for TRAP No. 6 Information [3]:fjdaryTrapSensorInfo Normal Information [4]:fjdaryTrapMessage ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 110
Information [5]:fjdaryTrapMessage Information [6]:fjdaryTrapWarningInfo fjdarye100 Notification of 1.3.6.1.4.1.211.4.1. Information [3]:fjdaryTrapItemId SensorStatus alarm cancel for 1.126.1.100.0.26 Information [4]:fjdarySspMachineId ChangeTo TRAP No. 6 Information [5]:fjdaryTrapSensorInfo Normal Information [6]:fjdaryTrapMessage ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
ETERNUS Web GUI or ETERNUS CLI. For details on the sense code that is notified to the server, refer to "A.2.6 Sense Codes" (page 149). ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Meaning Hot spares Thin Provisioning Volume(s) Thin Provisioning Pool SMART Self-Monitoring Analysis and Reporting Technology Firmware Hard Disk Drive Solid State Drive Direct Memory Access ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
: CM module ID (10 – 11) : CM number (0 – 1) : Model name (DX80S2 or DX90S2) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 114
Model name (DX80S2 or DX90S2) : EXP number (0) : Port number (0 – 1) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 115
: CM module ID (10 – 11) : CM number (0 – 1) zz: Model name (DX80S2 or DX90S2) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 116
: CM number (0 – 1) : Port number (0 – 1) pp... : Component number ss... : Serial number rr... : Version oo... : Additional information ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 117
: CM number (0 – 1) : Port number (0 – 1) pp... : Component number ss... : Serial number rr... : Version oo... : Additional information ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 118
: CM module ID (10 – 11) : CM number (0 – 1) : Model name (DX80S2 or DX90S2) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 119
: CM number (0 – 1) during maintenance : Model name (DX80S2 or DX90S2) operations. pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 120
: Disk information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 121
: Disk information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 122
: Drive information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 123
: Disk information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 124
: Drive information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 125
Error Severity : Component subtype Level in the event : DE-ID ("00" for a controller enclosure) notification setting. This is not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 126
The copy sessions are in normal status. M 13CE0006 13CE0006 Halt session was cleared. Halt status in the copy session was removed. The copy ses- sionsares in normal status. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 127
: RAID group number (hexadecimal) dant" is enabled for Error Severity Level in the event notification setting. This is not notified during main- tenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 128
Level in the event Copyback to the replaced drive is complete. notification setting. : RAID group number (hexadecimal) They are not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 129
: CM number (0 – 1) in which the pinned data occurred event notification : CPU number in CM setting. This is not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 130
E2070010 NOT READY(16:DE Build Error) The device is in Not Ready status. Failed to configure DE because of QSFP cable errors or FC cable errors. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 131
WARNING(decrease of available capacity) Usage status of the Flexible Tier Pool is changed: Normal to Warning or Attention to Warning : FTRP number (hexadecimal) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 132
Error : Key server ID Severity Level in the : Key group ID event notification setting. This is not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
: CM module ID (10 – 11) : CM number (0 – 1) : Model name (DX80S2 or DX90S2) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 134
: Port number (0 – 1) : CM number (0 – 1) : Model name (DX80S2 or DX90S2) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 135
: Device number (0 – 1) zz: CA type : CM number (0 – 1) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 136
7B000000 CE Intake temperature Warning Level in the event notification setting. CE intake temperature error (Warning) is detected. They are not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 137
: Disk information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 138
: Disk information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 139
: Drive information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 140
: Drive information (RAID level or hot spare (Spare)) pp... : Component number ss... : Serial number rr... : Version tt... : Data code : Configuration code ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 141
: CM module ID (10 – 11) : CM number (0 – 1) zz: Model name (DX80S2 or DX90S2) pp... : Component number ss... : Serial number rr... : Version ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 142
: Component subtype : DE-ID ("00" for a controller enclosure) This row indicates TrapWarningInfo for Trap No. 5 and TrapSensorInfo for Trap No. 6. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Snap Data Pool (encrypted) usage rate exceeds the threshold (Level2) and reaches : Threshold of Snap Data Pool : Usage rate of Snap Data Pool ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 144
Buffer Volume" is No free space in the ODX Buffer volume. enabled for : ODX Buffer volume No. Informational Level in the event notification setting. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 145
&c: Type (Global or Dedicated) &d : RAID group number (only for Dedicated Hot Spares) &e : RAID group name (only for Dedicated Hot Spares) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 146
Device shutdown has started. I 01050030 – – Controller firmware updated ( Detail information is not displayed. Controller firmware version is updated. xxxx (Firmware version) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 147
CA port exceeds the maximum. in the event : CM number (0 – 1) notification setting. : CA number (0 – 1) : Port number (0 – 1) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 148
Normal status is restored for an intake temperature setting. error in CE or DE. This row indicates TrapWarningInfo for Trap No. 25 and TrapSensorInfo for Trap No. 26. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
This sense code is notified when "Not ready" is enabled for Error Severity Level in the event notification setting. This is not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 150
CM EXP Out port is disconnected. CM NAND Controller is disconnected. CM SCU is disconnected. CA port is disconnected. CM FPGA is disconnected. CM LAN Port is disconnected. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 151
Bad Data (data lost identifier) exists. "Complete rebuild" is enabled for Error Severity Level in the event notification setting. They are not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 152
CM SCU error is detected. CA error is detected. CA port error is detected. CM FPGA error is detected. CM LAN port error is detected. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 153
"Temperature Warning" is enabled for DE intake temperature error is detected. Warning Level in the event notification setting. They are not notified during maintenance operations. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
"110" is output as a priority value for an audit log. For the "RFC3164" format, the HEADER part follows the priority part. For the "RFC5424" format, "1" and then a blank follow the priority part. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 155
For the "RFC3164" format, a comma and then a blank follow this item. For the "RFC5424" format, a blank, a hyphen, and a blank follow this item in this order. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED...
Page 156
The user name of the account which performed the target event process is output. If the user which performed the target event cannot be specified, no values are output. A comma, and then a blank follow this item. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 157
Login Logged in to the storage system. Detail information is not displayed. 01010002 Logout Logged out from the storage system. Detail information is not displayed. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 158
: Drive (DE-ID + Slot number (example: [Disk= 0000, 0001, 0002)) 02030001 Register Thin provisioning License The Thin Provisioning license is registered. Detail information is not displayed. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 159
The Eco-mode schedule is assigned to or released from the RAID group. [No= Schedule_No= Action= : RAID group number : Eco-mode schedule number : Eco-mode action (OFF, ON) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 160
: Migration source volume number [No= 02050008 Start Balancing Thin provisioning Volume The balancing of the Thin Provisioning Volume is started. [No= : Volume number ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 161
: Volume number [No= 0205000E Set Volume Encrypt The encryption setting of the volume is changed. : Volume number [No= Encryption= : Encryption by CM (Enable, Disable) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 162
: Transfer rate (1.5Gb, 3Gb, 6Gb, Auto) : Host response name : Reset Scope (Initiator, Target) : Release Reservation if Chip is Reset (Enable, Disable) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 163
: REC Sync transfer mode (Enable, Disable) : REC Stack transfer mode (Enable, Disable) : REC Consistency transfer mode (Enable, Disable) : REC Through transfer mode (Enable, Disable) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 164
[Name= [LUN= Volume= : Affinity group name or LUN group name : Affinity group number or LUN group number : Host LUN : Volume number ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 165
: Volume number that is to be added or changed 02060014 Release Mapping The LUN mapping setting is released. : Port group name [Port_Group= Port= : Port number ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 166
Set Port Group The port group settings are changed. : Port group name [Name= New_Name= Port= : New port group name : Port number (example: 001, 002) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 167
The access settings from the host is changed. : Port number (example: 001, 002) [Port= Host= &b State= : Host name : State (Online, Offline) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 168
: EC/OPC priority (Auto, High, Low, Very Low, Middle) : Copy schedule mode (Session Balancing, Dst RG Balancing) 02080007 Initialize Snap Data Volume The SDV is initialized. : SDV number [No= ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 169
: Drive (DE-ID + Slot number (example: 0000, 0001, 0002)) : Assigned CM (0, 1) : Encryption by CM (Enable, Disable) : Stripe Depth (64KB, 128KB, 256KB, 512KB, 1024KB) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 170
: LAN port (MNT, RMT) Engine_ID= Version= : Authentication Failure Trap (Enable, Disable) : Engine ID (example: 12, 13 ... or "Default") : MIB-II version (RFC1213, RFC4293) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 172
: Common Name : Subject Alt Name 020B0003 Import SSL Certificate The SSL server key and the SSL certificate are registered. Detail information is not displayed. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 173
: Port number for syslog server 2 020B0007 Set SED Key Machine Name The key management machine name is set. Key management machine name [Machine_Name= ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 174
: Administrator information : Description for the storage system 020C0003 Set Encryption The encryption mode is enabled or disabled. : Encryption mode (Fujitsu, AES, Disable) [Mode= ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 175
(Enable, Disable) : Early detection-and-isolation of a failed disk (Enable, Disable) : Use "Add Host Group" (Enable, Disable) : Use "Add Host" (Enable, Disable) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 176
Forced Write Back Write back is forcibly performed. Detail information is not displayed. 020C0018 Forced Restore Restoration is forcibly performed. Detail information is not displayed. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 177
: Timeout limit [minute] (5 – 60) 020D0001 Update Customer Information The customer information is registered or updated. [Delete_Customer_Identity_Info= : Deletion of the customer information in the storage system (Yes, No) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 178
(MNT, RMT) 020D000B Set Remote Support The remote support parameters are set. : Deletion of the customer information in [Delete_Customer_Identity_Info= the storage system (Yes, No) ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 179
The license for the additional host interface port is registered. Detail information is not displayed. 020E000B Upgrade Storage System Model The storage system model is upgraded. : Mode (Canceled) [Mode= ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 180
The log file is exported. : Customer Information (Enable, Disable) [Customer_Info= 02100008 Export Pinned Data The pinned data is exported. Detail information is not displayed. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 181
: Flexible Tier Pool number [No= 0211000C Stop Balancing Flexible Tier Pool Balancing of Flexible Tier Pool is stopped. : Flexible Tier Pool number [No= ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 182
The path group for Storage Migration is deleted. : Path group number [No= 03010001 Force Unlock The exclusive resources are forcibly released. Detail information is not displayed. ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 183
: fjdaryTrapMessage detected Information INFORMATIONAL Information event from , message: %s An information- event (*2) level event is : fjdarySspMachineId detected : fjdaryTrapMessage ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 184
: fjdaryTrapSensorInfo normal status : fjdaryTrapMessage For variable-bindings values, refer to "variable-bindings meanings" (page 111) "A.1.3 SNMP" (page 107). The default setting is "Disable" (no notification). ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation- Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0...
Page 185
However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the use of information in this manual. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual.