Packard Bell Vibe 100 Disassembly Manual
  1. Manuals
  2. Brands
  3. Packard Bell Manuals
  4. MP3 Player
  5. Vibe 100
  6. Disassembly manual
Packard Bell Vibe 100 Disassembly Manual

Packard Bell Vibe 100 Disassembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Packard Bell
Vibe 100
Disassembly Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vibe 100 and is the answer not in the manual?

Questions and answers

Related Manuals for Packard Bell Vibe 100

Summary of Contents for Packard Bell Vibe 100

  • Page 1 Packard Bell Vibe 100 Disassembly Manual...

  • Page 2: Table Of Contents

    Table of Contents Overview Technician Notes Disassembly Instructions Reassembly Instructions Required Tools Hazardous Voltage Avoid Electrostatic Discharge Power Supply Unit Opening the Casing Removing the Battery Removing the Hard Disk Removing the Mainboard/LCD assembly Notice Packard Bell Vibe 100 Disassembly Manual...

  • Page 3: Overview

    The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws that are removed are shown next to the image of the parts themselves. Packard Bell reserves the right to make changes to the Vibe 100 MP3 player without notice. Technician Notes Only technicians authorized by Packard Bell should attempt to repair this equipment.

  • Page 4: Hazardous Voltage

    (un)installed in the MP3 player. lo enlaces de telecomunicaciones, de red y de líneas de módem. No ponga en funcionamiento el lector Packard Bell Vibe 100 Disassembly Manual...
  • Page 5 Non avviare il behuizing geopend wordt. Zet de MP3 speler Vibe 100 senza aver prima messo a nooit aan als de behuizing geopend is. posto il coperchio. Packard Bell Vibe 100 Disassembly Manual...

  • Page 6: Opening The Casing

    1. Lift up the foil with product specifications on the backside; under the lower side corners are two screws. 2. Remove the two screws 3. Remove the cover, and lift the battery out, so that its connector is freely accessible (see Fig. 2). Packard Bell Vibe 100 Disassembly Manual...

  • Page 7: Removing The Hard Disk

    To remove the top cover, open the player (see Opening the Casing), remove the battery (see Removing the Battery), then perform these steps: 1. Lift out the hard disk. Fig. 3 The hard disk is lifted out. Packard Bell Vibe 100 Disassembly Manual...

  • Page 8: Removing The Mainboard/Lcd Assembly

    1. Lift up the mainboard to reach the HDD flat cable connector. 2. Lift up the tape covering the HDD connector. 3. Now push down the two clips on the side of the connector. 4. Take out the flat cable. Packard Bell Vibe 100 Disassembly Manual...
  • Page 9 The plastic LCD bracket should be properly clicked into the mainboard before inserting it into the top cover (else there will be too much pressure on the LCD panel when fixing it inside the casing. (see Fig. 6) Fig. 6 The LCD plastic bracket Packard Bell Vibe 100 Disassembly Manual...
  • Page 10 9. Make sure the hold switch is properly aligned (see Fig. 7) Fig. 7 The hold switch Packard Bell Vibe 100 Disassembly Manual...

  • Page 11: Notice

    INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. Copyright © 2006 Packard Bell B.V. All rights reserved. Company names and product names mentioned herein may be trade names, trademarks and/or registered trademarks of their respective owners.

Table of Contents