Disable Duplex Unit; Disable Inverter Unit; Disable Stapler Unit; Disable Paper Desk Drawers - Sharp AR-C260P Key Operator's Manual

I Device settings
These programs are used to enable or disable the
use of a peripheral device, and select other modes,
registration adjustment, and auto paper selection
setting. (See pages 27 to 28)

Disable duplex unit

This program is used to disable duplex printing
when the duplex module malfunctions. When this
program is enabled, only one-sided printing can be
performed.
"DISABLE DUPLEX UNIT" is displayed as
indicated in the chart on page 27.

Disable inverter unit

Use this program when you need to prohibit the
inverter function
bypass/inverter unit has failed. When the program
is enabled, pages are only output face-down to the
centre tray of the machine. Duplex printing is also
prohibited (only one-sided printing is possible).
"DISABLE INVERTER UNIT" is displayed as
indicated in the chart on page 27.

Disable stapler unit

This program is used to disable stapling when the
stapler unit of the
malfunctions.
"DISABLE STAPLER UNIT" is displayed as
indicated in the chart on page 27.

Disable paper desk drawers

This program is used to disable use of the stand/1
x 500 sheet paper drawer, stand/3 x 500 sheet
paper drawer or duplex module/2 x 500 sheet
paper drawer when
malfunctions.
"DISABLE PAPER DESK DRAWERS" is displayed
as indicated in the chart on page 27.

Disable finisher

This program is used to disable use of the saddle
stitch finisher when it malfunctions.
"DISABLE FINISHER" is displayed as indicated in
the chart on page 27.

Disable large capacity tray

This program is used to disable use of the large
capacity tray when it malfunctions.

Disable shifter unit

Use this program when you need to prohibit the
shifter (offset) function in the centre tray or when
the shifter has failed.
"DISABLE SHIFTER UNIT" is displayed as
indicated in the chart on page 27.
or when the duplex
saddle stitch finisher
one of these units
DESCRIPTION OF PROGRAMS

Saddle stitch adjust

This program is used to adjust the stapling position
(folding position) when using the saddle stitch
function of the optional saddle stitch finisher.
The value can be adjusted in 0.1 mm increments
within ±3.0 mm from the reference position for
each paper size.
"SADDLE STITCH ADJUST" is displayed as
indicated in the chart on page 27.
Max. +3 mm
Position adjusted
to the plus
direction
1
2
Reference position

Auto paper selection setting

Use this program to select the paper type* for
which the automatic paper selection function
operates. Selections are "PLAIN", "R&P" (recylcled
and plain), and "RECYCLED".
* This is the paper type set for each paper tray in
the paper tray settings of the custom settings
(page 2-11 of the OPERATION MANUAL (for
general information)).
"AUTO PAPER SELECTION
displayed as indicated in the chart on page 27.

Registration adjustment

Use this program when the colour of characters
and lines in colour printing is off. Registration
adjustment can be performed in two ways:
manually and automatically. Normally [AUTO
ADJUSTMENT] should be used.
"REGISTRATION ADJUSTMENT" is displayed as
indicated in the chart on page 28.
Auto adjustment
Use this program to perform automatic registration
adjustment.
When "AUTO ADJUSTMENT HAS COMPLETED.
[OK]" appears, press the [OK] key to end the
program.
"AUTO ADJUSTMENT" is displayed as indicated
in the chart on page 28.
Manual adjustment
Use MANUAL ADJUSTMENT when you require a
higher degree of precision than can be obtained
with AUTO ADJUSTMENT.
See page 10 for the procedure for manually
adjusting the registration.
"MANUAL ADJUSTMENT"
indicated in the chart on page 28.
Min. -3 mm
Position adjusted
to the minus
direction
12
11
SETTING" is
is displayed as
9