Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric P95DW
Summary of Contents for Mitsubishi Electric P95DW
- Page 1 DIGITAL MONOCHROME PRINTER MODEL P95DW P95DE OPERATION MANUAL THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL MONOCHROME PRINTER. DIGITAL MONOCHROME PRINTER This digital monochrome printer complies with the requirements of the EC Directive 93/42/EEC.
- Page 3 FOR THE MODEL P91DW(UB) ONLY WARNING: In the USA or Canada, use the AC power cord according to the recommendations as below, in order to comply with UL60601-1 and CAN/CSA C22.2 No. 601.1. Case 1. Connect to the 120V receptacle of the room or the host equipment. The AC power cord should be UL or CSA approved and consist of type SJT, size 16 or 18AWG, length 2.5m or shorter cord with IEC60320-1/C13 type, 125V 10A or higher rating connector and NEMA 5-15 type, 125V 10A or higher rating,...
-
Page 4: Explosion Hazard
Indications according to IEC60601-1 1. Functions and intended usage of this product This product receives signals from diagnostic imaging equipment or a personal computer, and automatically prints and ejects the received image data on the thermal paper. 2. Classifi cation of this product •... - Page 5 CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning fl ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage"...
- Page 6 This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV. Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.
- Page 7 The Model P95DW/P95DE should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, the Model P95DW/P95DE should be ob- served to verify normal operation in the confi guration in which it will be used.
- Page 8 Guidance and manufacturer's declaration - electromagnetic emissions The Model P95DW/P95DE is intended for use in the electromagnetic environment specified below. The customer or user of the Model P95DW/P95DE should assure that it is used in such an environment. Compliance Emissions test...
- Page 9 Guidance and manufacturer's declaration - electromagnetic immunity The Model P95DW/P95DE is intended for use in the electromagnetic environment specified below. The customer or user of the Model P95DW/P95DE should assure that it is used in such an environment. IEC/EN 60601...
- Page 10 The Model P95DW/P95DE is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the Model P95DW/P95DE can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the Model P95DW/P95DE as recommended below, according to the maximum output power of the communications equipment.
-
Page 11: Table Of Contents
CONTENTS CONTENTS ..............1 PRECAUTIONS ............. 2 - 5 UNPACKING ..............6 FEATURES AND FUNCTIONS ....... 7 - 8 Front Panel ..................7 Rear Panel ................... 8 INSTALLATION OF PAPER ......... 9 - 10 EXAMPLE OF CONNECTION ........11 PRINTING ............12 - 13 ADJUSTMENT OF PRINT PICTURE .... -
Page 12: Precautions
PRECAUTIONS In the interest of safety, please observe the following pre- WARNING : THIS APPARATUS MUST BE EARTHED. cautions: AVERTISSEMENT : CET APPAREIL DOIT ETRE MIS POWER REQUIREMENT A LA TERRE. This digital monochrome printer is designed for operation This equipment is classifi ed as class , according to the on 100-240V AC 50/60Hz. -
Page 13: Thermal Paper
Note: If the paper absorbs non-volatile organic solvents (al- Mitsubishi brand thermal paper is specially treated with cohol, ester, katone, etc.) the print may be discolored. an anti-static coating against thermal head damage Particularly, if the paper comes in contact with soft caused by static-electricity discharge. - Page 14 SAFETY TECHNICAL CHECKS Periods: According to the recommendations of the manufacturer of medical device. Scope: a) Visual check Housing, cables, operator controls, readout device (displays, LED etc.), labels, accessories, instruction manual. b) Function test Performance check acc. instruction manual, also unity and applicability of set and accessory test.
-
Page 15: Product Outline
INTENDED USE The digital monochrome printer P95DW/P95DE is intended for use as a hard copy device for an image generated by a diagnostic imaging equipment. This product is intended to be used together with medical equipment and to be used for reference purpose, not for di-... -
Page 16: Unpacking
UNPACKING Take the unit out of the box by the following procedures. Make sure to check the contents. Open the top of the box. Take the unit out of the box carefully. • Make sure to keep the unit horizontal. Remove the cushion above the unit. -
Page 17: Features And Functions
FEATURES AND FUNCTIONS Front Panel OPEN button SHARP (sharpness) button Press this button to open the door. Press this button and then turn the adjustment control to adjust the Indicator sharpness of the print images. See page Displays stand-by, functions and error messages. -
Page 18: Rear Panel
Rear Panel Potential equalization terminal This is used to equalize the potential of the equipment connected to this unit. For details refer to the installation instruction of equipment to be connected. USB terminal Connects to the device equipped with a USB interface such as a personal computer. -
Page 19: Installation Of Paper
INSTALLATION OF PAPER Moisture, fi ngerprints or dust on Pull out the paper end. the paper surface may cause a noise at printing or deterioration in print quality. Set the paper by • Pull out the fi rst 15- the following procedure to prevent 20cm (6 in. - Page 20 When setting the paper, observe the following precautions to prevent paper jam. Do not use defective paper. Do not use bent or wrinkled paper. Adjust the paper position correctly. When the paper is fed out skewed from the print exit, adjust the paper position so that it is fed out straight.
-
Page 21: Example Of Connection
EXAMPLE OF CONNECTION Connecting to various equipment with USB interface such as medical equipment and personal computer. Connection Connect the digital monochrome printer with PC or medical equipment through a USB cable. Personal computer or medical equipment To USB terminal Connect Power cord Rear panel... -
Page 22: Printing
PRINTING Printing method Turn on the power. Cut the printed paper. • Press the • Cut the printed POWER paper with the switch on the cutter by rear panel to tearing off the turn on the paper in the power. upper right direction. - Page 23 Paper Feeding To feed the paper, press the FEED button on the front panel. When you release the FEED button within about 1 second after starting paper feeding, paper feeding automatically stops after feeding about 20 mm of the paper. Precautions on Printing When dark pictures are printed consecutively, the digital monochrome printer may become overheated and the indicator blinks.
-
Page 24: Adjustment Of Print Picture
ADJUSTMENT OF PRINT PICTURE Adjustment of Brightness, Contrast and Sharpness You can make fi ne adjustment of brightness, contrast and sharpness of the picture to be printed. Control panel • For adjustment, use the BRT " ", CONT " " or SHARP " "... - Page 25 Change the setting. Store the set value. By pressing the button being selected • Turn the control again, the setting value is memorized. clockwise to increase The memorized value will not be lost the value. even when the power is turned off. •...
- Page 26 Automatic restoration to the standby status from the adjust- ment or setting mode When left without any operation of buttons, and switches under the following conditions for more than 20 seconds, this unit automatically returns to the standby status (Indicator display : In this case, the newly set value is not memorized and the setting goes back to the value that was set before change.
-
Page 27: Setting Function Mode
SETTING FUNCTION MODE Function mode In this mode, the initial setting value of each function can be changed. Each time the FUNC button is pressed, the mode is switched as follows. Functions Stand-by status Gamma curve setting Adjustment control lock setting USB iSerial number setting Setting the function mode By turning the adjustment control, you can change the setting... - Page 28 Gamma curve setting Indicator Purpose and description • To select the gamma ( ) curve (relation between the density and the brightness of the image) to obtain an optimum density depending on the connected device. Five options are available. • The default setting is 1. Adjustment control lock setting Indicator Purpose and description...
-
Page 29: Error Display
ERROR DISPLAY In case of an error in the unit during operation, you are warned by an alarm tone or the LED indicator. Symptom/Remedy Cause/Error display [Symptom] Overheat • When the head gets overheated, the indicator blinks. When overheat occurs while more than one copy is being processed, printing starts as soon as the error is solved. - Page 30 Symptom/Remedy Cause/Error display [Symptom] No paper • When the paper runs out or the paper is not installed, printing becomes impossible and an alarm tone is heard. In this case, all the buttons become invalid. • If this error occurs while more than one copy is being printed or there are images waiting to be processed, printing is cancelled at the occurrence of the error.
-
Page 31: Error Display
Symptom/Remedy Cause/Error display [Symptom] Door error • When the door opens, an alarm tone is heard. The indicator displays " ". In this case, all the buttons and switches become invalid. • If this error occurs while more than one copy is being printed, printing is cancelled at the occurrence of the error. -
Page 32: Status And Modes
STATUS AND MODES Set state/Mode Contents of LED display LED display Power off Power off Stand-by During data receiving During data receiving Print state Remaining number of copies / number of copies 1 to 99 100 to 199 Continuous copy printing Printer brightness mode Fine adjustment of the picture brightness Fine adjustment of the picture contrast... -
Page 33: Use Of Cleaning Paper
USE OF CLEANING PAPER When the thermal head is dirty with dust, etc., white spots or stripes may appear on the print. In this case, clean the thermal head by the following procedure BY USING THE SUPPLIED CLEANING PAPER. Turn on the power. Close the door. -
Page 34: Maintenance
MAINTENANCE Turn off the power for maintenance. Maintenance of Main Unit Wipe off stains of the front panel with a soft cloth. When the panel is heavily stained, wipe with a cloth moistened with neutral cleanser diluted by water and fi nish with a dry cloth. Maintenance of Rubber Roller When the rubber roller is dirty with dust, etc., a blank spot may appear on the print. -
Page 35: Specifications
SERVICE INFORMATION Before requesting service please review this operation manual to correct minor complaints. If you are unable to correct the problem, consult your MITSUBISHI Dealer or MITSUBISHI Service Department. DO NOT ADJUST ANY CONTROLS NOT DESCRIBED IN THIS OPERATION MANUAL.
Need help?
Do you have a question about the P95DW and is the answer not in the manual?
Questions and answers
есть ли возможность менять тип бумаги S HD HG