Contact Reverse - Genie GPS-IC Series Owner's Manual

7 7 7 7
FO O RC E E A A D D J J UST T ME E NT
. . . . . .
WARNING
Adjust your door operator so that minimum force
is needed to operate door.
Position ladder to the side of the power head so
that it is clear of all moving parts of the power
head, rail assembly and door.
During the following steps, the motor protector may
open. Wait about 20 minutes for protector to reset.
N N O O TE: Us s e wall c c ontrol l to run d d o o o o r to the fu u lly y
C C L L O O SE E D posi i ti o o n n bef f o o r r e e start t i i ng
a a a a d d j j u u u s s t t t m m m e e n n t t t t . . .
1. Adjust the OPEN Force (Fig. 7-1).
" "
Locate screw on back of power head marked
•
OPEN FORCE.
" "
Gently turn screw counterclockwise until it stops.
•
N N O O TE: : L L i i ttl e e ef f f f o o rt t is r r e e qu u i i red to o t t urn a a dju u s s tin n g sc c re e w.
Operate door using wall control.
•
If door does not completely open, turn
•
FORCE screw clockwise slightly.
"
Activate door using wall control.
•
Repeat force adjustment until door will
•
completely open.
N N OT T E: : Se e t t minim m um fo o rce requi i re e d t t o make doo o r o o pen.
Close door, use wall control.
•
2. Adjust the CLOSE FORCE
"
control to run door to the fully OPEN position
before starting CLOSE FORCE
"
Locate screw on back of power head marked
•
CLOSE FORCE.
" "
Gently turn screw counterclockwise until it stops.
•
N N O O TE: : L L i i ttl e e ef f f f o o rt t is r r e e qu u i i red to o t t urn a a dju u s s tin n g sc c re e w.
Operate door using wall control.
•
If door does not completely close, turn
•
FORCE screw clockwise slightly.
"
Operate door using wall control.
•
Repeat force adjustment until door will
•
completely close.
N N OTE: Set t the m m inim m u u m m fo o r r c c e r r e e qui r r e e d to ma k k e the
d d o o o o r r clo o s s e . . Smal l ler r t t h h e e number r th h e e sm m a a l l l er the
f f f f o o o o r r r c c e e . .
3.

CONTACT REVERSE

Fine adjustments for limit switches (see Section 8)
MUST BE completed before starting CONTACT
REVERSE.
Open door, use wall control.
•
Place a 2 by 4 board laid flat in center of doorway.
•
Close door.
•
Door MUST stop and reverse to open position. If it
•
does not, repeat fine adjustments for down limit
switch and CLOSE FORCE
"
door will reverse to the open position.
N N OT T E: : Set mini i mu u m f f o o rce r r equi i red t t o make d d oo o r clo o se. .
If door does not reverse, decrease
until door reverses.
O O PE E N FO O RCE
" "
MOR MOR
OPEN
"
OSE
LI
(Fig. 7-1). Use wall
"
adjustment.
"
CLOSE
"
(Fig. 7-2)
adjustment until the
"
CLOSE FORCE
" "
F F OR HELP-1.800. . 35 5 4.3643 3 OR GENIE E C C O O MPANY.C C O O M
OP N
CL SE
STEALTH
OR
LIMIT
SET
OPEN
FORCE
MORE
CLOSE
FORCE
FORCE
RADIO
SIGNAL
LEARN
CODE
PRO MAX
Fig. 7-1
CONTACT REVERSE
Fig. 7-2
1
2
NEC
CLASS 2
3
4
MO E MORE
PUSH
TO SET
C OSE OPEN
LIM TS
L MIT ADJUSTMENT
NEC
CLASS 2
USH
1
UTT N
2
OM
NOTE
AFE Y
3
USE O LY W TH
EAM
ER E CON RO S
4
O N T
P SH
L M T 5
N E S
O R I
A T C E
6
IMIT
ET
PEN
CLOSE OPEN
OR
MORE MORE
LOS MORE
ORCE FORCE
ADIO
IGN L
CLOSE OPEN EARN
ODE
LIMIT ADJUSTMENT
U S Pa ent No 5 243 7 4
5 221 869
1 1/2 Object
"
(or a 2 x 4
laid flat)
23