Genie GPS-IC Owner's Manual
  1. Manuals
  2. Brands
  3. Genie Manuals
  4. Garage Door Opener
  5. GPS-IC Series
  6. Owner's manual

Genie GPS-IC Owner's Manual

Automatic chain drive/belt drive garage door operator system
Hide thumbs Also See for GPS-IC:
Table of Contents

Advertisement

Quick Links

Automatic
Chain Drive/Belt Drive
Garage Door Operator
System
Complete with
and SERIES II Electronics
Operator MUST be installed with the included SERIES II Wall Control!
Self-diagnostic Electronic Sensory Protection System
(SAFE-T-BEAM SYSTEM) MUST Be Installed To Close Door!
Owner's Manual
SAVE FOR FUTURE REFERENCE
Customer Service
C A L L : 1 - 8 0 0 - 3 5 4 - 3 6 4 3
V I S I T : W W W . G E N I E C O M P A N Y . c o m
AUTOMATIC GARAGE DOOR OPERATOR SYSTEMS
HANG MANUAL NEAR YOUR WALL CONTROL
Remote Control
GPS-IC Series
PMX-IC B Series

TABLE OF CONTENTS

SECTION
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
ASSEMBLY
1
OPERATOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
1A Channel and Power Head Assembly . . . . . . . . . . .10
1B Rail and Power Head Assembly . . . . . . . . . . . . .10-11
INSTALLATION
2
2B Installation on Trackless Doors . . . . . . . . . . . . 15-17
3
4
WALL CONTROL INSTALLATION . . . . . . . . . . . . . . . . . . . . 20
5
CONNECT OPERATOR TO POWER . . . . . . . . . . . . . . . . . . 21
6
MAIN LIMIT SWITCH SETTINGS . . . . . . . . . . . . . . . . . . . . . 22
OPERATION
7
FORCE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Contact Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8
FINE LIMIT SWITCH ADJUSTMENTS . . . . . . . . . . . . . . . . . 24
9
REMOTE CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
10 BATTERY & VISOR CLIP INSTALLATION . . . . . . . . . . . . . . 25
11 LIGHT BULB AND LENS INSTALLATION . . . . . . . . . . . . . . 26
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
3507535556
PAGE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GPS-IC and is the answer not in the manual?

Questions and answers

Related Manuals for Genie GPS-IC

Summary of Contents for Genie GPS-IC

  • Page 1: Table Of Contents

    WARRANTY ..........32 3507535556 GPS-IC Series PMX-IC B Series OPERATOR ASSEMBLY .

  • Page 2: Pre-Installation Check List

    The Genie Company recommends that you read and fully understand all information and instructions contained herein before choosing a “Do-It-Yourself ” installation. Any questions should be directed to the Genie Company or an authorized Genie Dealer. ( The issue numbers below refer to the circled numbers in the illustrations on page 3.

  • Page 3: Typical Sectional Door Installation

    TYPICAL SUPPORT BRACKET 36” POWER CORD 120V GROUNDED OUTLET EXTENSION SPRING TORSION SPRING TYPICAL (TRACKLESS) 1-PIECE DOOR INSTALLATION TYPICAL (TRACK GUIDED) 1-PIECE DOOR INSTALLATION TYPICAL SECTIONAL DOOR INSTALLATION ADDED HEADER BRACKET MOUNTING BOARD BRACES SAFE-T-BEAM ® ONE-PIECE DOOR SECTIONAL DOOR...

  • Page 4: Safety Information

    SAFETY INFORMATION OVERVIEW OF POTENTIAL HAZARDS Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual.

  • Page 5: Parts Identification

    PARTS IDENTIFICATION NOTE: Accessories vary by model. FASTENERS - Shown full size. See Parts List for description. Bolt, #10-24 x 1/2” Bolt, 5/16”-18 x 1/2” Phillips Hex Head Screw, No. 10 x 1-1/4” Lag Screw, 1/4” x 2” Speed Nut Cold Head Pin FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM vary by model...

  • Page 6: Parts Identification

    PARTS IDENTIFICATION Stealth Power Head Combined Parts List Item Part Name Lens Front Cover Side Cover (by series/model) Top Plate Assembly Strain Relief Cord & Plug Assembly Component Panel (by series/model) Bottom Cover Screw, #8 x .75 Phil Hx Hd/W Sf Tap Screw, #8 x .62 Phil Pan Hd/W Sf Tap Screw, #8 x .50 Slt Hx Hd/W Sf Tap Screw, #8 x .38 Slt Hx Hd/W Sf Tap...
  • Page 7 PARTS IDENTIFICATION FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 52 64 PRO-MAX Power Head Item Part Name Main Drive Worm Screw, #8 x 3-1/8” Slot HH, Sf Tap Limit Switch Plate Screw, #6 x 3/8” Phillips w/Wshr, Sf Tap Screw, #4 x 5/8”, Slot HH w/Wshr, Sf Tap...
  • Page 8 PARTS IDENTIFICATION Channel Combined Parts List Item Part Name Belt & Bullet Assembly - 7’6” Door (Belt Models Only) Belt & Bullet Assembly - 8’ Door (Belt Models Only) Belt & Bullet Assembly - 10’ Door (Belt Models Only) Belt & Bullet Assembly - 12’ Door (Belt Models Only) Sprocket Bushing Sprocket, 10 Tooth - 7’6”...
  • Page 9 PARTS IDENTIFICATION Item Part Name Boom Support Kit (not shown) Safety & Maintenance Guide Emergency Release Tag (Tri-L) Entrapment WARNING Label Wire Rail (L=112.475”) Screw, 5/16”-18 x 3/4” Screw, 5/16” x 1/2” HH w/Wshr Pulley Support Chain Sprocket Saddle Screw, 5/16”-18 x 2-1/4” HH Bolt Retainer Screw, 5/16”-18 x 1-1/8”...

  • Page 10: Operator Assembly

    OPERATOR ASSEMBLY OPEN BLUE PARTS BAG Screws for attaching light cover are included in this bag. Please set aside for use later. 1. Attach emergency release knob cord (Fig. 1-1). • Tie overhand knot in end of cord. • Thread cord through knob so knot is inside knob. •...

  • Page 11: Determine Door Type And Mounting Method

    5. Fasten rail to power head. • Align mounting holes of sprocket saddle, rail and power head frame. • Insert the two (2) 5/16” x 1/2” hex head screws[112], then two (2) No. 10-24 x 1/2” hex head screws [69]. •...

  • Page 12: Installation On Track Guided Doors

    Alternate Mounting Methods NOTE: Materials for mounting are not included Angle Iron Method FOR TRACK GUIDED DOORS – FOR TRACKLESS DOORS GO TO PAGE 15 – WARNING • Do Not try to remove, repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items.
  • Page 13 CAUTION Header bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 3. Install header bracket (Fig. 2-3) • Place bracket so: – center hole is on line “V.” – all holes are on line “H.” •...
  • Page 14 “V” Top of Door Dessus de la porte “V” [ 96 ] [ 79 ] Sectional doors 8. Install door bracket (Fig. 2-6). • Contact door manufacturer. NOTE: Self-drilling screws are intended for use with light-weight door only, while lag screws are meant for wood doors only.

  • Page 15: Installation On Trackless Doors

    FOR TRACKLESS DOORS WARNING • Do Not try to remove, repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items. Repairs and adjustments must be made by a trained service person using proper tools and instructions.
  • Page 16 5. Install door braces (See CAUTION below). CAUTION Doors made of masonite, lightweight wood, fiberglass, and metal must be properly braced before mounting an operator. Contact door manufacturer or distributor for bracing instructions. 6. Install door bracket (Fig. 2-12). • Contact door manufacturer for proper installation. NOTE: Self-drilling screws are intended for use with light-weight door only, while lag screws are meant for wood doors only.
  • Page 17 OPEN YELLOW PARTS BAG CAUTION Mounting bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 9. Mount power head (See Section 2 ALTERNATE MOUNTING METHODS). • Be sure rail assembly and power head are on door center line (line “V”).

  • Page 18: Safe-T-Beam ® (Stb) System Installation

    SAFE-T-BEAM ® INSTALLATION WARNING There should be no electrical power to the operator while installing Safe-T-Beam ® System wires. If you have plugged in the power cord —UNPLUG IT NOW. NOTE: The operator will not close the door automatically unless the Safe-T-Beam ® System is installed.

  • Page 19: Self-Diagnostic "Stb" System Troubleshooting

    CAUTION Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the STB System to stop working. When using the insulated staples, make sure you fasten them only as tightly as needed to hold the wire snugly. •...

  • Page 20: Wall Control Installation

    WALL CONTROL INSTALLATION WARNING Power cord must be unplugged before attaching wires. Be sure wire ends do not touch each other or other terminals. CAUTION • Use of any other wall control will cause the light not to work and could cause door to operate by surprise.

  • Page 21: Connect Operator To Power

    CONNECT OPERATOR TO POWER WARNING To reduce the risk of electrical shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet. If the plug does not fit into the outlet, contact a qualified electrician to install the proper outlet.

  • Page 22: Main Limit Switch Settings

    MAIN LIMIT SWITCH SETTINGS WARNING Door opens rapidly. • Keep path clear. • Position ladder to the side of power head so it is clear of all moving parts of door and operator. Set door operator so minimum force is needed to operate door.

  • Page 23: Force Adjustment

    FORCE ADJUSTMENT WARNING Adjust your door operator so that minimum force is needed to operate door. Position ladder to the side of the power head so that it is clear of all moving parts of the power head, rail assembly and door. During the following steps, the motor protector may open.

  • Page 24: Fine Limit Switch Adjustments

    FINE LIMIT SWITCH ADJUSTMENT During the following steps, the motor protector may open. Wait about 20 minutes for protector to reset. 1. Adjusting the “OPEN” limit switch (Fig. 8-1). • Run door to open position by pushing wall control. • Locate curved “OPEN” limit adjustment slot on back of power head.

  • Page 25: Battery & Visor Clip Installation

    • Press and release a remote control button. – LED on power head stops blinking. • Press and release same remote button again. – LED goes out. Remote is now programmed. 2. Program multi-button remote control • Repeat step 1 (“program one-button remote” for each button).

  • Page 26: Light Bulb And Lens Installation

    LIGHT BULB AND LENS INSTALLATION 1. Install light bulb(s) into socket(s). Do Not use short neck bulb(s). • Use bulb(s) rated for: – rough service. – vibration. – appliances. • 100 watt maximum. 2. Bend two (2) slotted tabs up. This will activate the ”living hinge”...

  • Page 27: Maintenance

    KEEP GARAGE DOORS PROPERLY BALANCED. See Owner's Manual. An improperly balanced door increases the risk of severe injury or death. Have a Genie Factory Authorized Dealer make repairs to cables, spring assemblies, and other hardware. SAVE THESE INSTRUCTIONS. FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM...

  • Page 28: Troubleshooting Guide

    TROUBLESHOOTING GUIDE Use this guide to correct problems with your door operator. If these solutions do not work, call Customer Service. CAUTION Use only with included SERIES II wall control Use of any other wall control can cause the door to operate unexpectedly and the light not to work.

  • Page 29: Wiring Diagram

    WIRING DIAGRAM FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM CAUTION Opening cover could cause electrical shock. ( Stealth Motor ) ( ProMax Motor )

  • Page 30: Accessories

    $4.00 Instructions Commandant Pas d’expédition contre remboursement. Veuillez inclure un chèque ou un mandat bancaire, le payable fait à The Genie Company. N’envoyez pas d’argent comptant. Accordez de 3 à 4 semaines pour la livraison. 1-800-354-3643. Ayez sous la main le numéro de la pièce et celui de la carte de crédit. Mettre à...
  • Page 31 INSTALLATION NOTES CONTACT NUMBERS NAME NAME NAME NAME NAME NAME FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM COMPANY COMPANY COMPANY COMPANY COMPANY COMPANY NUMBER NUMBER NUMBER NUMBER NUMBER NUMBER...

  • Page 32: Warranty

    Geographic scope: This warranty applies only to Genie products purchased in the United States, Canada or Mexico. What we will do: If your Genie product is defective, we will repair it or, at our option, replace it at no charge to you. If we repair your Genie product, we may use new or reconditioned replacement parts.

This manual is also suitable for:

Pmx-ic bStealthPmx-ic b series

Table of Contents