Sharp AR-P17 Software setupg guide Software Setup Manual page 20

USING THE MACHINE WITH A PARALLEL OR USB CONNECTION
Do not select liPS Printer Driver".
The PS printer driver for the
machine should only be installed
Iromthe
CD-ROM
thataccompanies
the AR-PH printer expansion kit.
DI~iJajlBEADME
I
._ .t'!.ame '- __ '_
o
()'~S
Printer
D,iv~
i'2l ~
PSDisplay Font
Packoge
Select Cl package to be installed.
Follow the on-screen instructions.
~
Select the "PS Display Font" checkbox .
and click the "Next" button.
l(DcautiO"
I
II the lanquaqe selection screen
appears after you double click the
"Setup" icon, select the language that
you wish to use and click the "Next"
button. (Normally the correct language
is selected automatically.)
Click the "start" button, click "My
Computer"
(~),
and then double-click
tile CD-ROM icon (
\id ).
In Windows 95/98/Me/NT 4.0/2000,
double-click "My Computer", and then
double-click the CD-ROM icon.
Double-click the "Setup" lcon
(~).
Insert the PS3 expansion kit AR-PK1
PRINTER UTILITIES CD-ROM into your
computer's CD-ROM drive.
If your computer is configured for auto
start on the CD-ROM, proceed to step 4.
The fonts used by the PS printer driver are contained in the "PRINTER UTILITIES" CD-ROM that
accompanied the PS3 expansion kit (AR-PK1). Install these fonts as needed for the PS printer driver.
INSTALLING THE PS DISPLAY
FONTS
,
.
r
USB
r
SI",,";?,;"'"'
r.
Porollel
r.
Connected 10In.. oampuler
Selectan inl", acelobe coon.doli
5.1.01 how ~~'" 1"",10' will b. oomee'.d
Cnoa•• an in,i.II.Uon illothod
E'O<:\JIe!he in".II.lIo~ by,...ohing .'MfP'oonnoolod la
,haTCP/lP
nelwOJk
oulo""l'lo.llY.
1~1.I"ork·~brl
i. oloolod
",lhLPFI_lio.I!Y,J
C"~'Cmin"'II'lIon~
E,.ouleths,,,,talalio<'l by'olllng. MFP with Tep/IP
network conneol"", n~otk ,h.to. U58 """".cl;on. 0'
poi.llejconneotiorL
fiW;IlH:mO@'ffllMil!ffiOH
I.
When you are asked how the printer is
connected, select "Connected to this
computer" and click the "Next" button.
If you are using Windows 95/NT 4.0, go to
step 12.
When the interface selection screen
appears, select "Parallel" and click the
IINext" button.
• Click the "Custom installation" button.
IiI
Click the" Next" button.
Double-click "My Computer"
(~),
and
then double-click the CD-ROM icon (~).
Selecta sortware to be installed.
I
IS'~
... ,,1
Insert the CD-ROM into your computer's
CD-ROM drive.
The "SOFTWARE LICENSE" window will
appear. Make sure that you understand
the contents of the license agreement,
and then click the "Yes" button.
If the language selection screen
appears after you double click the
"Setup" icon, select the language that
you wish to use and click the "Next"
button. (Normally thecorrect language
is selected automatically.)
The parallel cable must not be connected
to the machine. Make sure that the cable
is not connected before proceeding.
If the cable is connected, a Plug and Play
window will appear. If this happens, click
the "Cancel" button to close the window
and disconnect the cable.
Click the "Printer Driver" button.
To view information on the software, click
the "Display Readme" button.
(cPNote)
The cable will be connected in step21.
~
Double-click the "Setup" icon
(~).
• Read the message in the "Welcome"
window and then click the "Next" button.
Installation in Windows 95/98/Me/NT 4.0/2000 (parallel cable)
18
23