Configuring The Printer Driver - Sharp AR-P17 Software setupg guide Software Setup Manual

USING THE MACHINE WITH A PARALLEL OR USB CONNECTION
USING THE PPD FILE
<;.l",llhodriver!<>;",t.1I
r.' PS
[<
NOI., 11 ~O" .,,,,,110 prinld"e"'l1 P5.l'OO need the oplion!i "
"PS
o,p.o::>on
1;,1",
Th.PPD d''''.r" nOlill,lollodho,e, See
I
!he.olupgr><lelo;",t.IIPPO
r-
PCL6
This completes the installation of the software.
• If you installed the printer driver, configure the
printer driver settings as explained in
"CONFIGURING THE PRINTER DRIVER"
(p.25).
011 youinstalledth_e_!,§-,)~nje-'.drivEJr,the
PS
display font call
be
illsfalledfroin the - - -
"PRINTER UTILITIES" CD-ROM that
accompanied the PS3 expansion kit (p.23).
Make sure that the power of the
machine is turned on, and then
connect the USB cable. (p.20)
Windows will detect the machine and the
Plug and Play screen will appear.
I
Follow the instructions in the Plug and
Play screen that appears in your
version of Windows to begin the
installation.
After completing the above steps, repeat the
installation procedure from step 1 if you are
installing the PCL5e or PS printer driver.
1. Repeat the installation procedure from step 1.
2. When the select printer driver to install
screen appears, remove the checkmark from
"PCL6" and select the checkbox of the
printer driver that you wish to install
("PCL5e" or "PS").
~"kno"""ol'".repocl;og,
Th. M,OtOloll 69it.' "!l'\1lluro ollllm,that,oil...,. h..
~e"" le,led w~il\if.,d""".r>d Ih., Ih. '011""'0 11" nD!
b.er..II ...d,,,,,,.,'WO,lo,l,d
II~ou.,anllo"';ohlotM",ro:oftdogil.lly"gn,,"
'01'''",0
1'l"llh,WIt>do"'~i>d'I.W.b,'
• .,
Wpll",ndDw,opd",miC1O<oli oomlo , ,,,, il o,,,, i,
"".,Ioblo
Th.,oll''''.I'O'J., •• """II"''''ldildo,,nolcon'~".
l.I,o,oooll<igllol,ign,iul.Therelole,lb"oi,,,,,
guaranleell1al'h"",rr""oWDIk,oorreclly,,"h
W"' O O",,
.. US8
~eIoclon",I"rloc"lobeco"rN'.d
In Windows 2000, if the following
screen appears while thefiles are being
copied (themessage may appear more
than once), click the "Yes" button.
Afterthe installation, a message
prompting you to restart yourcomputer
may appear. In this case, clickthe
"Yes" button to restart yourcomputer.
When the interface selection screen
appears, select "USB" and click the
11
Next" button.
fjl/.\;ijl.ji@
fUG w¥Ht1rffM'ZT
Select whether or not you wish to
install the display font and click the
11
Next ll button.
When "The installation of the SHARP
software is complete" appears, click the
"OK" button.
Follow the on-screen instructions.
'V\lhen the "Finish~..,creenalJpears,
click the'IIClose
ll -
button. - ----------------
A message will appear instructing you to
connect the machine to your computer.
Click the "OK" button.
l(Dcautio"
I
If printerresident fonts cannot be
specified fromthe application
software, the resident font information
has not been installed or the
information is not correct. In this case,
reinstall the resident font information.
Follow the on-screen instructions.
After the resident font information has
·beenoinstalled,.restarLyour.•computer..•. ~~~.~ .. ~~ .•.
c.
~ Follow the on-screen instructions.
When you are asked to specify the path of
the PPD file, enter the path as follows.
(Substitute the letter of your CD-ROM
drive for "R" in the following paths.)
*
In regions other than the U.S., enter "English"
instead of "EnglishA".
Operating system
PPD file path
Windows
95/9B/Me
R:\Drivers\Printer
\EnglishA\PPD\9XME
Windows NT 4.0 R:\Drivers\Printer
\EnglishA\PPD\NT40
Windows 2000/XP R:\Drivers\Printer
\EnglishA\PPD\2KXP
• If you are using Windows 2000 or Windows XP, the resident font information is automatically
installed when the PPD file is installed.
• Before installing the resident font information, be sureto install the PPD file.
Click the "start" button, click "Control
Panel", click "Printers and Other
Hardware", and then click "Printers and
Faxes ll
•
in operating systems other than Windows
XP, click the "Start" button, select
"Settings", and then click "Printers".
Click "Add a printer" in "Printer Tasks".
In Windows 95/9B/Me/NT 4.0/2000,
double-click the "Add Printer" icon.
The "Add Printer Wizard" will appear.
Insert the CD-ROM into your computer's
CD-ROM drive.
Insert the CD-ROM into your computer's
CD-ROM drive.
Double-click the "Drivers" folder, the
"Printer" folder, the "EnglishA" folder
(for regions other than the U.S.,
double-click the "English" folder), the
"PPD" folder, the "9XME" folder, and
"PFMSetup.exe".
Double-click" My Computer" (~), and
then-double-click-the. . CD-ROMjconc..
~
•• c
(~).
The PPD file enables the machine to print using the standard PS driver of the operating system, and
can be used when the optional PS3 expansion kit AR-PK1 is installed. Install the PPD file as needed.
Use the Add Printer Wizard in Windows to install the PPD file.
Be sure to read the Readme file before installing the PPD file. The Readme file is in the "EnglishA" or
"English" folder. For the location of the folder, see step 4.
If you have installed the PPD file in Windows 95/9B/Me and will use the resident font, you must install
resident font information for PPD. Follow the procedure below to install the resident fonts information.
Installing the resident font information for PPD (only
when the PPD file is installed in Windows 95/9B/Me)
24
17