Table of Contents
Advertisement
Owner's Manual
(RrlFTXMrlN°
15.5 HP
ELECTRIC START
42" MOWER
6 SPEED TRANSAXLE
LAWN TRACTOR
Model No.
917.270654
•
Safety
• Assembly
• Operation
• Maintenance
• Repair Parts
CAUTION:
Read and follow all Safety Rules
and Instructions before operat-
ing this equipment.
For answers to your questions
about this product, Call:
1-800-659-5917
Sears Craftsman
Help Line
5 am - 5 pm, Mon - Sat
Seam, Roebuck and Co., Hoffman Estates, II 60179
Visit our Craftsman
website:www.sears,com/craftsman
Advertisement
Table of Contents
Related Manuals for Craftsman 917.270654
Summary of Contents for Craftsman 917.270654
- Page 1 Call: Read and follow all Safety Rules 1-800-659-5917 and Instructions before operat- Sears Craftsman Help Line ing this equipment. 5 am - 5 pm, Mon - Sat Seam, Roebuck and Co., Hoffman Estates, II 60179 Visit our Craftsman website:www.sears,com/craftsman...
- Page 2 Please contact your nearest service center. After 30 days from the date of purchase, warranty service is available by taking your Craftsman riding equipment to your nearest Sears Service Center. (in-home warranty service will still be available after 30 days from the date of purchase but a standard trip charge will apply).
- Page 3 DO NOT: • Turn off blades when not mowing. • Do not turn on slopes unless neces- • Stop engine before removing grass san/, and then, turn _lowly and catcher or unclogging chute. • Mow only in daylight or good artificial gradually downhill, if possible.
- Page 4 • Keep nuts and bolts, especially blade • Never make adjustments or repairs attachment bolts, tight and keep with the engine running. equipment in good condition. • Grass catcher components are subject • Never tamper with safety devices. to wear, damage, and deterioration, Check their proper operation regularly.
- Page 5 FT. LBS. Service Center/Department (See REPAIR PARTS section of this manual). TORQUE: CONGRATULATIONS on your purchase of a Craftsman Tractor. It has been designed, engineered and manufactured to give you the best possible depend- ability and performance. Should you experience...
- Page 6 Steering Wheel 11) Hex Bolt 3/8-16 x 1 (1) Large Flat Washer (1) Hex Bolt 5/16-18 x 1-1/4 (1) Locknut 5/16-18_ (1) Lockwasher 3/8 Steering Wheel Steering Extension Adapter //" Steering Shaft Boot Seat (1) Washer (1) Shoulder 17/32 x 1-3/16 x 12 Gauge Bolt 5/16-18 _(1) Knob...
- Page 7 Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes, To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
- Page 8 TO ROLLTRACTOR OFF SKID (See Label Operation section for location Seat function of controls) • Press lift lever plunger and raise Terminal attachment lift lever to its highest Batten Door position. • Release parking brake by depressing "re clutch/brake pedal. •Ptace gearshift lever in neutral (N) position.
- Page 9 CHECK PROPER POSITION INSTALL MULCHER PLATE OF ALL BELTS (If previously removed) • Raise and hold deflector shield in See the figures that are shown for replacing motion and mower blade drive upright position, belts in the Service and Adjustments •...
- Page 10 These symbols may appear on your tractor or in literature supplied with the product. Leam and understand their meaning. BATI'E RY CAUTION OR REVERSE FORWARD FAST SLOW WARNING ENGINE ON ENGINE OFF OIL PRESSURE FUEL CHOKE MOWER HEIGHT PARKING BRAKE UNLOCKED MOWER LIFT LOCKED...
- Page 11 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations various controls and adjustments. Save this manual for future refe:_nce. Light Switch Ignition Switch Attachment Clutch Lever...
- Page 12 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
- Page 13 • Move gearshift lever to 1st gear. • The average lawn should be cut to sure you have allowed room for tractor approximately 2-1/2 inches during the to roll slightly as you restart movement. cool season and to over 3 inches •...
- Page 14 ADO GASOLINE Insert key into ignition and turn key clockwise to "START" position • Fill fuel tank. Use fresh, clean, regular release key as soon as engine starts. unleaded gasoline with a minimum of Do not run starter continuously 87 octane. (Use of leaded gasoline will increase carbon and lead oxide...
- Page 15 MULCHING MOWING TIPS MOWING TIPS IMPORTANT: For best performance, • Mower should be properly leveled for best mowing performance. See "TO keep mower housing free of built-up LEVEL MOWER HOUSING" in the grass and trash. Clean after each use. Service and Adjustments section of •...
- Page 16 MAINTENANCE SCHEDULE J_./-_/_n_ Check Operator Presence and Intedock Systems Check for Loose Fasteners Sharpen'Replace Mower Blades Lubdc.ation Chart Check Batter'/Level Clean Battwy end Terminals Check Transaxle Cooling Adjust Blade Belt(s) Tensk_n Adjust Motk_n Odve Belt(s) Tension Check Engine Oil Level Change Engine Oil Clean Air Filter Clean Air Screen...
- Page 17 IMPORTANT: To ensure proper assem- TRACTOR bly, center hole in blade must align with Always observe safety rules when star on mandrel assembly. performing any maintenance. • Reassemble hex bolt, lock washer BRAKE OPERATION flat washer in exact order as shown. If tractor requires more than six (6) feet •...
- Page 18 NOTE: Although multi-viscosity oils BATTERY (5W30, 10W30 etc.) improve starting Your tractor has a battery charging cold weather, these multi-viscosity oils system which is sufficient for normal use. will result in increased oil consumption However, periodic charging of the battery when used above 32°F.
- Page 19 • Clean cartridge by tapping gently on ENGINE COOLING FINS flat surface. If very dirty or damaged, Remove any dust, dirt or oil from engine replace cartridge. cooling fins to prevent engine damage • Reinstall cartridge, nut, precleaner, from overheating. cover and secure with knob(s).
- Page 20 CLEANING We do not recommend using a garden hose to clean your tractor unless the of all foreign matter. electrical system, muffler, air filter and Keep finished surfaces and wheels carburetor are covered to keep water out. Clean engine, battery, seat, finish, etc. free of all gasoline, oil, etc.
- Page 21 Before making any necessary adjust- TO LEVEL MOWER HOUSING ments, check that both front links are Adjust the mower while tractor is parked on level ground or driveway. Make sure equal in length. Both links should be tires arepropedy inflated (See "PROD- approximately 10-3/8".
- Page 22 TO REPLACE MOWER BLADE • Road test tractor for proper stopping DRIVE BELT distance as stated above. Readjust The mower blade drive belt may be necessary. If stopping distance is still replaced without tools. Park the tractor greater than six (6) feet in highest on level surface.
- Page 23 TRANSAXLE GEAR SHIFT LEVER • Replace washers and snap retaining ring securely in axle groove. NEUTRAL ADJUSTMENT • Replace axle cover. The transaxle should be in neutral when NOTE: To seal tire punctures and the gear shift lever is in neutral (N) (lock prevent flat tires due to slow leaks, tire gate) position.
- Page 24 PositiveTerminal Negative Terminal Bolt Negative (Black) Positive (Red) Cabte Cable TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. Battery • Replace bulb in holder and push bulb holder securely back into the hole in Negative Terminal...
- Page 25 TO ADJUST CARBURETOR ENGINE NOTE: The carburetor on this engine is Maintenance, repair, or replacement low emission. It is equipped with an idle the emission control devices end fuel adjusting needle with a limiter cap, systems, which are being done at the which allows some adjustment within the customers...
- Page 26 ACCELERATION TEST Idle Speed Throttle Screw Lever ° Move throttle control lever from slow to fast position. It engine hesitates dies, turn idle mixture valve out (counter-clockwise) 1/8 turn. Repeat test and continue to adjust, if neces- sary, until engine accelerates smoothly.
- Page 27 ethanol or methanol) can attract moisture Immediately prepare your tractor for which leads to separation and formation storage at the end of the season or if the tractor will not be used for 30 days or of acids during storage. Acidic gas can more.
- Page 28 TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Will not start • Out of fuel. • Fill fuel tank. • See"TO START ENGINE" • Engine not "CHOKED" properly. in Operation section. • Wait several minutes • Engine flooded. before attempting to start. • Bad spark plug.
- Page 29 TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Engine clicks but • Weak or dead battery. • Recharge or replace battery. will not start • Corroded battery terminals. • Clean battery terminals. • Loose or damaged wiring. • Check all wiring. • Faulty solenoid or starter.
- Page 30 TROUBLESHOOTING CHART CAUSE CORRECTION PROBLEM Poor cut - uneven • Worn, bent or loose blade. • Replace blade. Tighten blade bolt. I• Mower deck not level. • Level mower deck. • Clean underside of mower • Buildup of grass, leaves, and trash under mower.
- Page 31 TRACTOR -- MODEL NUMBER 917.270654 SCHEMATIC _AC_ BATTERY "_° FUSE STARTER AMMETER ..soG;_o_o __(OPTIONAL) CLUTCH / BRAKE (PEDAL UP) (PEDAL UP) " 1 SEAT SWITCH • IGNITION ..(NOT OCCUPIED) SWITCH C_L _T_C-H _ _6XK'E Ftl J_JK _ACK I BLAC x CLUT GROUNDING SPARK...
- Page 32 TRACTOR - - MODEL NUMBER 917.270654 ELECTRICAL...
- Page 33 TRACTOR -- MODEL NUMBER 917.270654 ELECTRICAL PART DESCRIPTION 144925 Battery 12 VOLT25 74760412 B_t Hex Hd 1/4-20uno x 3/4 156417 Case Battery 153664 Switch, Interlock Push-In 166182 Harness Asm Light W/4152j 4152J Bulb Light #1156 479gj Cable Battery 6 G_ 11 • red 146147 Cable Battery 6 Ga w/16 wire red 166180...
- Page 34 TRACTOR -- MODEL NUMBER 917.270654 CHASSIS AND ENCLOSURES _145...
- Page 35 TRACTOR -- MODEL NUMBER 917.270654 CHASSIS AND ENCLOSURES PART DESCRIPTION 169830 Chassis 169061 Drawbar 17060612 Screw, Roll 3/8-16 x 3/4 155272 Bumper Hood/Dash 168337)(013 Dash. STD533710 Bolt, Carriage 3/8-16 x 3/4 155927 Panel, Dash, L.H. 145660 Gr_l{e P/L ClipTinnerman 172107X010 Panel, Asm.
- Page 36 TRACTOR -- MODEL NUMBER 917.270654 GROUND DRIVE...
- Page 37 TRACTOR - - MODEL NUMBER 917.270654 GROUND DRIVE PART PART DESCRIPTION DESCRIPTION Screw 3/8-16 x 3/4 Transaxle (See Breakdown) 17060612 Cover Pedal BIkRound Peerless Model 206-545C 8883R Pulley Eng CI Mech 38deg LT/YT 146682 Spring Return DrakeT/a Zinc 140186 Bolt Hex 7/16-20 x 4 Gr 5 123666X Pulley Transaxle18/20"...
- Page 38 TRACTOR -- MODEL NUMBER 917.270654 STEERING ASSEMBLY...
- Page 39 TRACTOR - - MODEL NUMBER 917.270654 STEERING ASSEMBLY PART DESCRIPTION 139768 SteenngWheel 154427 Front Axle Assembly 156483 Spindle Assembly, L.H. 157473 Spindle Assembly, R.H. 6266H Bearing, Race, Thrust, Hardened 121748X Washer 25/32 x 1-5/8 x 16 Gauge 19272016 Washer 27/32 x 1-1/4 x 16 Gauge 12000029 Ring, Klip 3366R...
- Page 40 TRACTOR - - MODEL NUMBER 917.270654 ENGINE " _ "--, , OPTIONAL EQUIPMENT Spark Arrester "...
- Page 41 TRACTOR -- MODEL NUMBER 917.270654 ENGINE PART DESCRIPTION 162157 Control Throttle/Choke 17720410 Screw Hex Thd Cut 1/4-20x5/8 T Engine (See Breakdown) ..Briggs Model 28U707-1174-E3 Muffler Exhaust B&S Lt 137352 Gasket 1 313 Id Tin Plated 165291 13280324 Nipple Pipe 3/8 N]StX 3" 13200300 Elbow Std 90 Degree 3/8-18 Npt Washer Lock Ext Tooth 3/8...
- Page 42 TRACTOR - - MODEL NUMBER 917.270654 SEAT ASSEMBLY PART PART DESCRIPTION DESCRIPTION 140122 Seat 3350 BIk/blkCraftsman 121248X Bushing Snap BIk Nyl 50 Id 140551 Boll Rdhd Sht N_ 1/4-20x1-1/2 Bracket Pnt Pivot Seat (blk) 72050412 71110616 Bolt Fin Hex 3/8-16uoc X 1 134300 Spacer Split 28 X 96 Zinc...
- Page 43 TRACTOR -- MODEL NUMBER 917.270654 DECALS PART PART DESCRIPTION DESCRIPTION Decal. Fender 156368 Decal, Oper. Instr. 11 163207 Decal, V-belt Dr Sch 167178 Decal, Replcmnt 12 146046 Decal, Dash 163200 DecaI, HoodRh 13 163250 163202 DecaI, HoodLh 160396 Decal, V-belt Schematic 165388 Decal, Battery Dngr/Psn Eng Decal, Hp Engine...
- Page 44 TRACTOR - - MODEL NUMBER 917.270654 LIFT ASSEMBLY...
- Page 45 TRACTOR -- MODEL NUMBER 917.270654 LIFT ASSEMBLY PART DESCRIPTION 159460 Washer Asm Inner Spring W/Plunger 159471 Shaft Asm. Lift RH 105767X Pin Groove 12000002 E Ring #5133-62 19211621 Washer 21/32 x 1:x 21 Ga. 120183X Beadng Nylong 125631X Grip Handle Fluted 122365X ButtonPlungerRead 11 139865...
- Page 46 TRACTOR -- MODEL NUMBER 9i 7.270654 MOWER DECK • 106"< , 102 103 105 .146 103r\/_J 101/_,,_,,,,,,_/104 _147 1 1o2/_ >21...
- Page 47 TRACTOR -- MODEL NUMBER 917.270654 MOWER DECK PART PART DESCRIPTION DESCRIPTION Mower Deck Assembty,42" 139888 Bolt. Shoulger 5/16-18 UNC 165892 Bolt 131845 Arm Assembly, Pad, Brake STD533107 Bracket Assembly,Sway Bar, 133943 Washer, Hardened 138017 Front 55 155046 Arm, Idler Bracket Sway Bar 38/42" Deck .56 165723 Spacer, Retainer 165460...
- Page 48 TRACTOR - - MODEL NUMBER 917.270654 PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C 3SA 29B O'-_2 !I_.,--12 0_---28...
- Page 49 TRACTOR - - MODEL NUMBER 917.270654 PEERLESSTRANSAXLE- - MODELNUMBER206-545C KEY PART KEY PART DESCRIPTION NO. NO. DESCRIPTION NO. NO. Brake Lever 772147 Transaxle Cover 41A 790079 Screw 1/4 - 20 x 1-1 /4" 780086A Needle Bearing 5/8" 792073A Screw 1/4 - 20 x 2 1/4" 770128 Transaxle Case 42A 792085A...
- Page 50 TRACTOR -- MODEL NUMBER 917.270654 BRIGGS &STRATTON ENGINE-MODEL NUMBER 28U707,TYPE NUMBER 1174-E3 1022 914_' 1023 1033 VALVE OVERHAUL KIT 22 _ REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL lO18 LA.EL KITI _022 51A _...
- Page 51 TRACTOR -- MODEL NU MBER 917.270654 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707, TYPE NUMBER 1174-E3 _" _ REQUIRES SPECIAL TOOLSTO INSTALL SEE REPAIR INSTRUCTION MANUAL. 108A 634A_._ 127_ 51A_ LMT_ARBURETOR PARTNUMBER LOCAnONS 186 _ THIS CARBURETOR SERVICES BOTH CHOKE-A-MATIC AND MANUAL CHOKE SYSTEMS 121 CARBURETOR...
- Page 52 TRACTOR - - MODEL NUMBER 917.270654 BRIGGS & STRATTON ENGINE-MODEL NUM BER 28U707,TYPE NUMBER 1174-E3 013 ,_ I 3091 151ol 513 ,"_ 803 ,,F-_ 384 _" 305A 1051 _ " I 703÷ 1036 EMISSIONS LABEL...
- Page 53 TRACTOR - - MODEL NUMBER 917,270654 BRIGGS & STRATrON ENGINE-MODEL NUMBER 28U707,TYPE NUMBER 1174-E3...
- Page 54 TRACTOR - - MODE L NUMBER 917.270654 BRIGGS & STRATrON ENGINE-MODEL NUMB ER 28U707, TYPE NUMBER 1174-E3 PART PART DESCRIPTION DESCRIPTION 496412 Cylinder Assembly 94896 Screw (Flywheel Guard) 399265 Bushing/Seal 690602 Bushing-Throttle Shaft 391086 Seal-Oil 498030 Idle Mixture Kit 494238 Sump-Engina 94098 •...
- Page 55 TRACTOR -- MODE L NUMBER 917.270654 BRIGGS & STRATTON ENGINE-MODEL NUMBER 28U707,TYPE NUMB EFt 1174-E3 PART PART DESCRIPTION DESCRIPTION Gear-Pinion (For Steel Ring 94930 Screw (Cylinder Shield) 693713 Gear Only) 693551 Motor-Starter (For Steel Gear-Pinion (For Aluminum Ring Gear Only) 783A 693059 Ring Gear Only)
- Page 59 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SIGHTING ._. . CUT GUIDE Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face. Make turns gradu- ally to prevent tipping or loss of control.
- Page 60 For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME S" (1-800-469-4663) Para pedir servicio de reparaci6n a domicilio 1-800-676-5811 In Canada for all your service and parts needs call Au Canada pour tout le service ou les pi6ces 1-800-665-4455 For the repair or replacement parts you need: Call 6 am - 11 pm CST, 7 days a week...