Do you have a question about the B70 and is the answer not in the manual?
Questions and answers
Suzanne
March 2, 2025
My unit will not take in the water from the reservoir. Motor activated but no flow it’s a B70
2 comments:
Suzanne Owens
March 2, 2025
@Suzanne
Mr. Anderson
March 2, 2025
Your Keurig B70 may not be taking in water from the reservoir due to a few potential issues:
1. Clogged or Damaged Hose – If there is rust or debris in the hoses connected to the solenoids, water flow may be restricted. 2. Broken Internal Part – A small broken plastic fragment found in the reservoir could indicate an internal component failure affecting water intake. 3. Pump Damage or Obstruction – If the water pump has tears, dents, or other obstructions, it may not function properly and require replacement. 4. Solenoid Malfunction – If the solenoids controlling water flow are damaged or clogged, they may not allow water to be drawn from the reservoir.
Checking these components and performing necessary cleaning or replacement may resolve the issue.
Page 1
OWNER’S MANUAL: Getting the most from your new Platinum B70 Keurig Platinum B70 Keurig Elite B40 Keurig Brewer Brewer Brewer ® ® ® COMMENT UTILISER VOTRE CAFETIÈRE MANUEL D’UTILISATION : Tirez le meilleur de votre nouvelle cafetière Elite B40 de Keurig ®...
The use of accessory attachments not recom- tions or is damaged in any manner. Contact Do not, under any circumstances, cut or mended by the appliance manufacturer may re- Keurig Customer Service to report any remove the third (ground) prong from the ®...
Page 3
TABLE OF CONTENTS KEURIG GOURMET SINGLE CUP HOME BREWING SYSTEM ® Elite — Model B40 CAUTION: There are two sharp needles that puncture the K-Cup portion pack, ® Using Your Brewer one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
Open the box. and 2 brew sizes (Small Mug-7.25 oz. and Large case future shipping of the product is necessary. Mug-9.25 oz.) your Keurig Brewer gives you Remove enclosed literature. endless options to customize the size, flavor Turn the box on its side with front of box face WARNING: and brew that’s perfect for you.
Features Elite — Model B40 Brewer B40 Brewer Controls and Indicators Water Reservoir Lid K-Cup Portion Pack Housing Small Mug Button Auto Off Light (Green) ® Holder (E and F are the Water Reservoir Drip Tray Plate Large Mug Button Heating Light (Red) K-Cup Holder Assembly) Water Reservoir...
Page 6
SECTION 1 Priming & First Brew You cannot use your Keurig Brewer until ® Place Water Reservoir base into the left side IMPORTanT: fig. of the Brewer and be sure the Water Reser- it has been primed for its first use as set forth below.
CAUTION: K-Cup will be hot. CAUTION: There are two sharp needles that puncture the K-Cup, one above the K-Cup Holder Enjoy your first cup of Keurig Brewed Large Mug ® and the other in the bottom of the K-Cup Holder (9.25 oz.)
SECTION 1 First Brew adding Water Brewing Your First Cup (Continued) The red light next to ‘HEATING’ on the LED Control Center may be lit as The LED Control Center of your Brewer will the water is heated for the next brew cycle. The Brewer will be ready for indicate when the water level in the Water use in approximately 15 seconds.
Brewing hot Water The blue lights behind the Brew Buttons on the LED Control Center will flash. Be sure to have a mug or cup on the Drip Tray Plate and then Your Brewer is able to produce hot water for making hot cocoa in a packet, press a Brew Button.
SECTION 2 SECTION 3 Controls & Indicators Cleaning & Maintenance (LED Control Center) Programming auto Off Timer Feature cleaning External Parts Set the Brewer to turn off two hours after the last brew. Regular cleaning of the Brewer’s external components is recommended. Press the Power Button to turn on the Brewer.
De-Scaling Your Brewer The Funnel can be 2. Cleaning the Funnel — fig. removed from the K-Cup Holder by pulling on it until it pops off (fig. 9). The Funnel is Mineral content in water varies from place to dishwasher safe. To replace it, just snap it place.
SECTION Cleaning & Maintenance De-Scaling Instructions Step 4: You may need to perform additional water brew cycles if you notice any residual taste. A. PREPARE NOTE: If the red ‘DE-SCALE’ light is still illuminated on the LED Control Center Step 1: Make sure you have at least 48 ounces of undiluted white vinegar on after completing the procedure, repeat the de-scaling procedure above.
SECTION 4 Troubleshooting Situation Solution Situation Solution Brewer does not Plug Brewer into an independent outlet. Brewing a partial cup The Exit Needle may be clogged. (refer to page 11). • • have power Check to be sure that it is plugged in securely. •...
Brewer so that your purchase information will be stored SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO in our system. Keurig will, at its option, repair or replace the Brewer without YOUR B40 BREWER, INCLUDING ANY IMPLIED WARRANTY OF MER- charge upon its receipt of proof of the date of purchase.
Page 15
Keurig, Incorporated 55 Walkers Brook Drive Reading, MA 0187 Keurig, Incorporated is a wholly-owned subsidiary of Keurig Incorporated est une filiale à 100% de Green Mountain Coffee Roasters, Inc. Green Mountain Coffee Roasters, Inc. cLIcK, caLL OR ShOP I www.keurig.com I 1.8.901.BREW...
Need help?
Do you have a question about the B70 and is the answer not in the manual?
Questions and answers
My unit will not take in the water from the reservoir. Motor activated but no flow it’s a B70
@Suzanne
Your Keurig B70 may not be taking in water from the reservoir due to a few potential issues:
1. Clogged or Damaged Hose – If there is rust or debris in the hoses connected to the solenoids, water flow may be restricted.
2. Broken Internal Part – A small broken plastic fragment found in the reservoir could indicate an internal component failure affecting water intake.
3. Pump Damage or Obstruction – If the water pump has tears, dents, or other obstructions, it may not function properly and require replacement.
4. Solenoid Malfunction – If the solenoids controlling water flow are damaged or clogged, they may not allow water to be drawn from the reservoir.
Checking these components and performing necessary cleaning or replacement may resolve the issue.
This answer is automatically generated