性能、 规格 主体性能 EYSDA212XD EYSDA218XD EYSDA407XD 型号 小螺丝: 小螺丝: 小螺丝: 建议作业 M2.5 ~ M4.5 M2.5 ~ M4 M3.5 ~ M5 0.3 N ・ m ~ 2.5 N ・ m 0.3 N ・ m ~ 2.0 N ・ m 1.5 N ・ m ~ 4.4 N ・ m 扭矩设置范围...
Page 20
性能、 规格 (续) 电源适配器规格 EYSZP001 型号 AC100-240 V 50/60 Hz 2.6 A 输入电压 DC30 V 3 A 输出电压 0.16 W ( 100 V ) 0.21 W ( 240 V ) 待机功率 ※ 未连接螺丝刀主体的状态 590 g 质量 (重量) 约...
Page 23
Operating Instructions Electric Screwdriver Table of Contents EYSDA Series Model No.: EYSDA212XD SAFETY PRECAUTIONS ..... 2 EYSDA218XD NAMES OF PARTS ....... 8 EYSDA407XD Accessories/ Separately sold items ....9 PREPARATION BEFORE USE .. 10 Using Forward/ Reverse Lever ....... 10 Connecting to Power Supply ..
SAFETY PRECAUTIONS Always adhere to the instructions Below are the instructions you should always adhere to, to prevent human harm and property damage. ■ The severity of harm and damage caused by incorrect use is presented with the following. WARNING May cause death or serious injury.
Page 25
If the tool malfunctions or makes abnormal noises during use, immediately turn off the trigger switch and stop using it. Consult your dealer or Panasonic Customer Support Centre. Using it as is may result in injury. Following the Operating Instructions, attach a bit or other pointed tools, and accessories securely.
Page 26
SAFETY PRECAUTIONS Always adhere to the instructions WARNING Do not use a socket or wiring device in the manner of exceeding the rated value. Use only within electrical rated range. Exceeding the rated value due to an overloaded socket may cause heat generation resulting in fire.
Page 27
WARNING Disconnect the power plug between uses. Failure to observe this may cause poor insulation resulting in electric shock or fire from electric leakage. Prohibited If it is thundering, do not touch this unit or the power plug. Failure to observe this may result in electric shock.
Page 28
SAFETY PRECAUTIONS Always adhere to the instructions CAUTION If the tool becomes hot, interrupt the work and wait for it to cool down before use. Failure to observe this may cause burns. To disconnect the power plug, always hold the power plug without pulling the cord.
Page 29
CAUTION Do not work in an unusual position. Otherwise you may fall over and be injured. Always stand on a stable footing and keep a good balance. Do not use the tool when you are tired. Failure to observe this may cause an accident or injury. ...
NAMES OF PARTS Tool ■ Front View ■ Side View ⑩ ② ⑫ ① ② ⑨ ⑪ ③ ④ ⑤ ⑧ ⑥ ⑦ ① Screwdriver cord ⑦ Bit holder (for hex shaft, 6.35 mm) ② Screwdriver hanger mounting hole ⑧ Clutch cover ③...
Accessories (No bit is supplied.) ■ 2 m Screwdriver Cord ■ Clutch Cover ■ Grip Attachment ■ Screwdriver Hanger * Supplied for EYSDA407XD only Separately sold items ■ Power Adapter (EYSZP001) [For China only] [For Malaysia only] [For Thailand only] Power Cord 1 m Power Cord 1 m Power Cord 1 m...
PREPARATION BEFORE USE Using Forward/Reverse Lever Attaching Screwdriver Hanger With the forward/reverse lever, you Pull the screwdriver hanger can change the rotation direction of the lightly on both sides. Electric Screwdriver or lock the start. Pulling the screwdriver hanger hard Trigger may prevent it from returning to its switch...
Page 33
■ Bits That Can Be Attached to This Attaching Bit Unit ATTENTION 6.35 mm A B When attaching or removing a bit, set the forward/reverse lever to the “○ (Trigger switch locked)” position, and turn OFF the power Ball groove section* Centre switch of the power adapter.
Page 34
PREPARATION BEFORE USE (cont.) Attaching Grip Attachment Components of the attachment ① Grip attachment (A) x 1 The grip attachment can be attached to ② Grip attachment (B) x 1 all models. (Supplied for EYSDA407XD only) ③ Trigger x 1 It can absorb the reactive force during ④...
Connecting to Power Supply Attach the power cord to the power adapter. ATTENTION Power adapter Before connection, set the forward/ (sold separately) reverse lever to the “○” position to lock the trigger switch. P. 10 Use only our power supply (screwdriver cord, power adapter, and power cord).
HOW TO USE ■ Switching to Push Start Mode Switching Start Modes Set the forward/reverse This unit has two modes for rotation lever to the “○” position. start. The trigger switch gets locked. Switch them according to the work P. 10 before use.
Adjust the torque with the NOTE clutch handle. The lever trigger switch can be ① ② removed as shown in the following figure. ① To increase the output torque, turn the clutch handle clockwise. ② To decrease the output torque, turn the clutch handle anticlockwise.
HOW TO USE (cont.) Recommended Fastening Torque Chart (Reference Values) These data are reference values measured under the following measurement conditions. In actual work, they vary depending on the surrounding conditions (such as screws, materials, and fixing methods). EYSDA407XD EYSDA212XD EYSDA218XD ...
Starting Work Start rotation. In “lever start” mode, pull the lever. Set the rotation direction In “push start” mode, push toward with the forward/reverse the bit. lever. Lever start Push start When you set it to the “F” position and the “R” position, the motor rotates forward (clockwise) and reverses (anticlockwise) respectively.
HOW TO USE (cont.) Checking Fastening Status Finishing Work This unit notifies you of the work status Set the forward/reverse with the detection lamp. lever to the trigger switch ■ Fastening OK lock position. When the clutch activates and the screw Set it to the “○”...
CAPACITY AND SPECIFICATIONS Tool Capacity Model No. EYSDA212XD EYSDA218XD EYSDA407XD Machine screw: Machine screw: Machine screw: Recommended Work M3.5 to M5 M2.5 to M4.5 M2.5 to M4 Torque Setting Range 0.3 N ・ m to 2.5 N ・ m 0.3 N ・ m to 2.0 N ・ m 1.5 N ・...
Page 42
CAPACITY AND SPECIFICATIONS (cont.) Power Adapter Specifications Model No. EYSZP001 Input Voltage 100 - 240 V AC, 50/60 Hz 2.6 A Output Voltage 30 V DC, 3 A 0.16 W (100 V) 0.21 W (240 V) Standby Power * When the screwdriver itself is not connected Mass (Weight) About 590 g Size (Estimated...
CLEANING AND STORAGE Cleaning Storage ■ Wiping with Soft Cloth ■ Avoid the following conditions during storage. Disconnect the power plug from the outlet, remove the screwdriver cord from • Car cabin or other hot places the tool, and then wipe it with dry soft •...
Page 47
Panasonic service center when disposing of this product. Customer care number (Toll free) : 1800 103 1333 ,1800 105 1333 Please see the Panasonic website for further information on collection centers, etc. or call the customer care toll-free number https://www.panasonic.com/in/corporate/e-waste-management.html...