Page 1 Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2). For (*1) and (*2), refer to GREEN PRODUCT PROCUREMENT LEAD-FREE SOLDER. © TOSHIBA CORPORATION file://C:\Program Files\zeus\js\!!fcover.html 11.05.2015...
Page 2: Service Mode
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 1 из 16 ADJUSTMENT Service Mode Entering to Service Mode 1. Press button once on remote control. ↓ ↓ ↓ ↓ 2. Press button again and hold button down. ↓ ↓ ↓ ↓ Service Mode display 3.
Page 3 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 2 из 16 Displaying the Adjustment Menu Press MENU button on TV. Service Mode Press ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ Press Adjustment Mode Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC.
Page 4: Setting & Adjusting Data
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 3 из 16 Test signal selection Selection of the adjustment items PROGRAMME (on TV or remote control) Change of the data value Volume +/- (on TV or remote control) Adjustment menu mode ON/OFF MENU button (on TV) Initialization of the memory (IC510) "i+"...
Page 5 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 4 из 16 Item Name of adjustment Address BRTC BRIGHTNESS CENTER COLC COLOR CENTER UVTT BASE BAND TINT CNTX CONTRAST MAX OPT1 TV SET OPTION 1 00F1 OPT2 TV SET OPTION 2 00F2 OPT3 TV SET OPTION 3 00F3 OPT4...
Page 6: Function Description
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 5 из 16 FFH. The variable range depends on the adjusting item. I2C Bus Off Turn off I2C communication between IC500, IC210 and IC320. 1) Press and hold the i+ button on the remote control, then press the Volume + button on the TV.
Page 7 Стр. 6 из 16 Series Model name Panel vendor OPT4 value XV565D EU Digital 37XV565D 0x16 OPT4 Ex. OPT4 value 0x65 indicates that panel vendor is SAMSUNG and panel size is 32. Upper 4bit is decided as below table. OPT4 (Upper 4bit) (bit7)
Page 8 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 7 из 16 BIT (Binary) High nibble Low nibble E.g. If Bit D7-0 = 0101 1010, Hex data is 0x5A. Exit from Service Mode Pressing POWER button to turn off the TV once. Initialization of Memory Data of IC510 and Setting Data of Signal Unit After replacing IC510 or signal board, the following initialization is required.
Page 9 8) Set I2C check function of TVOP to enable. 9) Check the picture carefully. If necessary, adjust any adjustment item above. Perform "Auto tune" on the owner's manual. MODEL ID (HEX) Model name Panel vendor 0x19 37XV565D file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.056\37X... 11.05.2015...
Page 10 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 9 из 16 Initializing Data setting flowchart after replacing the Signal Unit file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.056\37X... 11.05.2015...
Page 11: Test Signal Selection
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 10 из 16 Test Signal Selection Every pressing of button on the remote control changes the built-in test patterns on screen as described below in Service Mode. Picture Signal Red raster Green raster Blue raster All Black All White Self Diagnostic Function...
Page 12 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 11 из 16 2. During diagnosis, the following displays are shown. * Self check display and Item are subject to the models. TV CPU SW Version: Version information of TV Micro SW: Display 1 byte data. (Hex) EEPROM Version: Version information of TV Micro EEPROM: Display 1 byte data.
Page 13 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 12 из 16 For current input: OK: Signal Sync Detected NG: No Sync Detected TV Status: "official" is normal. Bus Errors: "none" is normal. Block: (SCART (FULL)) (SCART (S+AV)) (Component/Composite) HDMI1 HDMI2 HDMI3 DTV (Digital Only) Version Check Mode 1.
Page 14 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 13 из 16 TV Model Boot Code Version Core SW Version Seine SW Version TV Micro SW Version: Version information of TV Micro SW: Display 1 byte data. TV Micro EEPROM Version: Version information of EEPROM: Display 1 byte data. EDID Checksum: EDID data check item.
Page 15: Led Indication
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 14 из 16 --COMP : Component input --PC : PC input --OK : A/D adjustment set correctly. --NG : A/D adjustment set incorrect. : A/D adjustment is not needed. Because its picture format is not used. LED Indication The Green and Red LEDs on the TV (at the bottom center of the TV) indicate the TV's status, as described below.
Page 16 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 15 из 16 3. Power TV on. 4. Insert SD card into the slot on FWA1209. The following OSD will be displayed: 5. Highlight OK and press the OK key on the remote. 6. Upgrading progress for OSD is displayed on TV as bellow. Please never power off while updating.
Page 17 ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 16 из 16 8. Remove the SD card. 9. Upon completion the power will off/on automatically. DTV Software Upgrade - from Boot Up 1. Extract upgrade files to an SD card. 2. Unplug TV. 3.
Page 18: Function And Operation
Стр. 1 из 3 FUNCTION AND OPERATION The Remote Control Simple at-a-glance reference of your remote control. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.239\37X... 11.05.2015...
Page 19 Стр. 2 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.239\37X... 11.05.2015...
Page 20 Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.239\37X... 11.05.2015...
Page 21: Controls And Input Connections
Стр. 1 из 2 FUNCTION AND OPERATION Controls and Input Connections A wide variety of external equipment can be connected to the input sockets on the side of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions.
Page 22 Стр. 2 из 2 Using the Controls and Connections file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.059\37X... 11.05.2015...
Page 23: Startup Application
Стр. 1 из 5 FUNCTION AND OPERATION Startup Application Before switching on the television put your decoder and media recorder to Standby if they are connected. Quick Setup file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.213\37X... 11.05.2015...
Page 24 Стр. 2 из 5 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.213\37X... 11.05.2015...
Page 25 Стр. 3 из 5 Auto Tuning file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.213\37X... 11.05.2015...
Page 26 Стр. 4 из 5 Auto Channel Update file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.213\37X... 11.05.2015...
Page 27 Стр. 5 из 5 Analogue Switch-off file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.213\37X... 11.05.2015...
Page 28: Dtv Settings
Стр. 1 из 4 FUNCTION AND OPERATION DTV Settings Channels file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.087\37X... 11.05.2015...
Page 29 Стр. 2 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.087\37X... 11.05.2015...
Page 30 Стр. 3 из 4 Manual Tuning file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.087\37X... 11.05.2015...
Page 31 Стр. 4 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.087\37X... 11.05.2015...
Page 32: Atv Manual Tuning
Стр. 1 из 4 FUNCTION AND OPERATION ATV Manual Tuning Tuning file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.410\37X... 11.05.2015...
Page 33 Стр. 2 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.410\37X... 11.05.2015...
Page 34 Стр. 3 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.410\37X... 11.05.2015...
Page 35 Стр. 4 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.410\37X... 11.05.2015...
Page 36: Software Upgrade
Стр. 1 из 3 FUNCTION AND OPERATION Software Upgrade Version Auto Upgrade file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.758\37X... 11.05.2015...
Page 37 Стр. 2 из 3 Searching for New Software Reset TV file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.758\37X... 11.05.2015...
Page 38 Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.758\37X... 11.05.2015...
Page 39: Safety Instruction
Handling the LCD Module Стр. 1 из 4 SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 40 Handling the LCD Module Стр. 2 из 4 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 41 Handling the LCD Module Стр. 3 из 4 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 42 Handling the LCD Module Стр. 4 из 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.741\37X... 11.05.2015...
Page 43: Panel Identification
Стр. 1 из 1 PANEL IDENTIFICATION Panel Identification If the several panels are alternatively used in the same model without amending the model name, the identification marking will be shown at the last digit of the set serial number on the specification label on the back cover.
Page 44 U06A U05A POWER MAIN U03A AC-SW U04B RMT U04A LED...
Page 45: Safety Precaution
Стр. 1 из 4 SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 46 Стр. 2 из 4 inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7. Parts mounting and routing dressing of wirings should be the same as that used originally.
Page 47 Стр. 3 из 4 Resistance values in orms ( ). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
Page 48: Product Safety Notice
Стр. 4 из 4 Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 49: Specification
Стр. 1 из 2 SPECIFICATION file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.936\37X... 11.05.2015...
Page 50 Стр. 2 из 2 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.936\37X... 11.05.2015...
Page 60: Schematic Diagram
Стр. 1 из 2 SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 61 Стр. 2 из 2 = Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4. Voltages read with DIGITAL MULTI-METER from point indicated to chassis ground, using a color bar signal with all controls at normal, line voltage at nominal AC volts.
Page 183: Parts List
Стр. 1 из 1 PARTS LIST All Block Block : Search 1 / 1970 Jump Page : Location : Search Parts No. : Block Location Parts No. Description U03A AC-SW (PE0533) U03A 75012739 PC BOARD ASSY, PE0533B1, AC-SW U03A AC-SW (PE0533) F850 75005842 FUSE, CARTRIDGE 5.2X20, FSL 250V 6.3A (EM) U03A AC-SW (PE0533)
Page 184 Стр. 1 из 1 PARTS LIST U03A AC-SW (PE0533) Block : Search 1 / 7 Jump Page : Location : Search Parts No. : Block Location Parts No. Description U03A AC-SW (PE0533) U03A 75012739 PC BOARD ASSY, PE0533B1, AC-SW U03A AC-SW (PE0533) F850 75005842 FUSE, CARTRIDGE 5.2X20, FSL 250V 6.3A (EM) U03A AC-SW (PE0533)
Page 185 Стр. 1 из 1 PARTS LIST U04A LED (PE0534) Block : Search 1 / 18 Jump Page : Location : Search Parts No. : Block Location Parts No. Description U04A LED (PE0534) U04A 75011070 PC BOARD ASSY, PE0534A1, LED U04A LED (PE0534) CB06 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z U04A LED (PE0534)
Page 186 Стр. 1 из 1 PARTS LIST U04B RMT (PE0534) Block : Search 1 / 15 Jump Page : Location : Search Parts No. : Block Location Parts No. Description U04B RMT (PE0534) U04B 75011071 PC BOARD ASSY, PE0534A2, RMT U04B RMT (PE0534) CB02 76619157 CAPACITOR, ELECTROLYTIC CHIP, 16V 100UF U04B RMT (PE0534)
Page 187 Стр. 1 из 1 PARTS LIST U05AS MAIN (PE0566) Block : Search 1 / 1887 Jump Page : Location : Search Parts No. : Block Location Parts No. Description U05AS MAIN (PE0566) U05AS 75012801 PC BOARD ASSY, PE0566C, MAIN U05AS MAIN (PE0566) B320 75011088 ACCESSORY FOR SCREW U05AS MAIN (PE0566)
Page 188 Стр. 1 из 1 PARTS LIST U06A KEY (PE0560) Block : Search 1 / 19 Jump Page : Location : Search Parts No. : Block Location Parts No. Description U06A KEY (PE0560) U06A 75011072 PC BOARD ASSY, PE0560A1, KEY U06A KEY (PE0560) GB01 23362042 DIODE, ZENER, UDZS6.8B U06A KEY (PE0560)
Page 189 Стр. 1 из 1 PARTS LIST Miscellaneous Block : Search 1 / 8 Jump Page : Location : Search Parts No. : Block Location Parts No. Description Miscellaneous B001A 75011199 LCD PANEL, LC370WUN-SAB1 Miscellaneous H001 75010735 TUNER, ENG37E05KF Miscellaneous MZ01A 75011515 WIRE, MF0211 Miscellaneous P801...
Page 190 Стр. 1 из 1 PARTS LIST Accessory Block : Search 1 / 6 Jump Page : Location : Search Parts No. : Block Location Parts No. Description Accessory Y101E 75012768 MANUAL, MANUAL FRANCE Accessory Y105 75010347 OWNERS MANUAL, STD EU Accessory Y130 75008381 REMOCON HAND UNIT, CT-90287...
Page 191 Стр. 1 из 1 PARTS LIST Cabinet Block : Search 1 / 7 Jump Page : Location : Search Parts No. : Block Location Parts No. Description Cabinet A201 75012769 CABINET/RACK FRONT BEZEL ASSY, FRONT BEZEL ASSY Cabinet A342 75011097 BUTTON ASSY, POWER Cabinet A345 23748087 WASHER, 10X4.2XT0.3TPO...
Page 192 Стр. 1 из 1 PARTS LIST Packing Block : Search 1 / 3 Jump Page : Location : Search Parts No. : Block Location Parts No. Description Packing A701 75012845 CARTON CASE TPO, CASE TPO Packing A702A 75012746 PAD TOP PACKING, TOP PACKING Packing A702B 75012747 PAD BOTTOM PACKING, BOTTOM PACKING...
Page 193 Стр. 1 из 2 PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 194 Стр. 2 из 2 : Metal Film : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.200\37X... 12.05.2015...

Toshiba 37XV565D Service Manual

Quick Links

Related Manuals for Toshiba 37XV565D

Summary of Contents for Toshiba 37XV565D

Table of Contents