Additional Safety Information; Batteries And Chargers - DeWalt DCE410 Instruction Manual

English
Before operating, inspect job site for hazards
•
including chemicals or waste that could remain
in pipes.
Before operating, read and understand all safety
•
and operating instructions including the fitting
manufacturer's installation instructions and the
instructions for any other equipment used with this
tool. Failure to follow all instructions and warnings
may result in property damage and/or serious
personal injury.
Secure and support the material to prevent
•
movement during operation.
Keep a firm grip on the tool at all times. Forces on the
•
tool may change during and after the operation.
Expansion operations may cause material pieces
•
to fly. Flying particles can cause permanent eye
damage. ALWAYS wear eye protection.
Always wear gloves when operating tool and
•
handling materials. The ends of the materials can be
sharp and can cause serious personal injury.
Always wear safety shoes to protect your feet from
•
sharp metal debris on the floor.
To reduce the chance of damage to your PEX
•
expander, always store your tool with the expander
head installed.
The expander cones sharp end may cause injury to
•
the user without the expander head installed.
Improper lubrication may lead to
•
defective connections.

Additional Safety Information


WARNING: Never modify the power tool or any part of
it. Damage or personal injury could result.

WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead‑based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from
chemically‑treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well‑ventilated
area, and work with approved safety equipment, such
as dust masks that are specially designed to filter out
microscopic particles.
6
Wear protective clothing and wash exposed areas
•
with soap and water. Allowing dust to get into your
mouth, eyes, or lie on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
Use the appropriate dust extractor vacuum to remove
•
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
Air vents often cover moving parts and should be
•
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.

CAUTION: When not in use, place tool on its
side on a stable surface where it will not cause
a tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack
but may be easily knocked over.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V .......................... volts
Hz ........................hertz
min ......................minutes
or DC ......direct current
....................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per minute
RPM .................... revolutions per minute
sfpm ................... surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the
safety instructions below and then follow charging
procedures outlined. When ordering replacement battery
packs, be sure to include the catalog number and voltage.
READ ALL INSTRUCTIONS
Important Safety Instructions for All
Battery Packs

WARNING: Read all safety warnings, instructions,
and cautionary markings for the battery pack,
charger and product. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or serious injury.
or AC/DC .... alternating or
direct current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all documentation
..................... do not expose to rain