Download
Share
Print this page
Toro Z Master 7500-D Series Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z Master Professional 7500-DSeries
  6. Setup instructions
Toro Z Master 7500-D Series Setup Instructions

Toro Z Master 7500-D Series Setup Instructions

Professional riding mower with 144in turbo force rear discharge mower
Hide thumbs Also See for Z Master 7500-D Series:

Advertisement

Quick Links

Download this manual
Z Master
With 144in TURBO FORCE
Model No. 72144—Serial No. 400000000 and Up
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Professional 7500-D Series Riding Mower
Description
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
Operator's Manual
Engine owner's manual
Registration card
Operator training material
Key
Register at www.Toro.com.
®
Rear Discharge Mower
Qty.
–
Add fuel to the machine.
–
Check the engine-oil level.
–
Check the tire pressure.
–
Check the wheel lug nut torque.
Raise the rollover protection system
–
(ROPS).
–
Check the hydraulic-fluid level.
–
Check the deck gearbox-fluid level.
–
Check the wheel gearbox oil.
Check the machine before delivery to
–
the customer (All machines).
1
1
1
Delivering the machine to the customer.
1
2
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3445-183 Rev A
Setup Instructions
Use
*3445-183*

Advertisement

loading

Related Manuals for Toro Z Master 7500-D Series

Summary of Contents for Toro Z Master 7500-D Series

  • Page 1 Operator's Manual Engine owner's manual Registration card Delivering the machine to the customer. Operator training material *3445-183* © 2021—The Toro® Company Original Instructions (EN) 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420 Register at www.Toro.com. All Rights Reserved...

  • Page 2: Adding Fuel To The Machine

    Adding Fuel to the Machine Checking the Tire Pressure No Parts Required No Parts Required Procedure Procedure Add fuel to the machine before starting it; refer to your Rear tires air pressure specification: 152 kPa (22 Operator’s Manual for the correct fuel and procedure. psi).
  • Page 3 Push on the roll bar and ensure that both pins are engaged (Figure Raising the Rollover Protection System (ROPS) No Parts Required Procedure g008619 WARNING Figure 2 To avoid injury or death from rollover, keep 1. Engaged position 2. Partially engaged—do not operate the machine the roll bar in the fully raised, locked position with the roll back in this...

  • Page 4: Checking The Hydraulic-Fluid Level

    Checking the Hydraulic-Fluid Level No Parts Required Procedure g228816 Park the machine on a level surface, disengage Figure 4 the blade-control switch, and engage the parking 1. Full line 2. Add line brake. Move the motion-control levers to the Replace the dipstick and thread the fill cap position and start the engine.
  • Page 5 Checking the Deck Gearbox-Fluid Level No Parts Required Procedure Park the machine on a level surface. Lower the mower deck to the 2.5 cm (1 inch) height of cut. Disengage the blade-control switch, move the motion-control levers to the N EUTRAL position, and engage the parking brake.
  • Page 6 Important: Do not overfill the gearbox; overfilling the gearbox may damage it. Checking the Drive Wheel Gearbox Oil No Parts Required Procedure Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
  • Page 7 Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures.
  • Page 8 Delivering the Machine to the Customer Parts needed for this procedure: Operator's Manual Engine owner's manual Registration card Operator training material Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished.
  • Page 9 Ensure that the customer receives the Operator's Manual, engine owner’s manual, Setup Instructions, and operator training material. Ensure that the customer knows the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine using a full-width trailer ramp.
  • Page 10 Notes:...
  • Page 11 Notes:...

This manual is also suitable for:

72144