Pioneer MJ-L7 Service Manual page 41

MJ-L7
@ OO: Measurement, ¢ ¢: Setting
@ When the + button of DISPLAY unit is pressed when the setting is displayed, the setting will increase and the new setting will be stored
in the RAM.
When the — button of DISPLAY unit is pressed when the setting is displayed, the setting will decrease and the new setting will be stored
in the RAM.
When the STOP button of the Unit is pressed when the EEPROM setting menu is displayed, the test mode STOP state will be set.
When the STOP button of the Unit is pressed in the TEMP setting menu state, the EEPROM setting menu state will be set.
When the STOP button of the Unit is pressed at each setting item display, the TEMP setting menu state will be set.
When the CHARACTOR button of DISPLAY unit is pressed in the EJECT state, the unit will move to step 5. (Refer to 6.2.8 EJECT State)
(6) Control Setting
Setting Method Remarks Display
Test mode STOP state [ts A Ace & |
Press the MENU button four times | Reads each setting from the EEPROM. [ EEPROM SET ]
EEPROM menu display mode
Press the PLAY/PAUSE button Focus setting menu [ Focus ]
Press the MENU button five times | CONTROL setting menu [ Control ]
Press the PLAY/PAUSE button CONTROL 1 setting [ CONTRL1 ¢¢]
Press the MENU button CONTROL 2 setting [ CONTRL2 ¢ 4]
@ ¢¢: Setting
@ When the CANCEL button of DISPLAY unit is pressed at a step, the unit will shift to the opposite step.
@ When the + button of DISPLAY unit is pressed when the setting is displayed, the setting will increase and the new setting will be stored
in the RAM.
When the — button of DISPLAY unit is pressed when the setting is displayed, the setting will decrease and the new setting will be stored
in the RAM.
When the STOP button of the Unit is pressed when the EEPROM setting menu is displayed, the test mode STOP state will be set.
When the STOP button of the Unit is pressed in the CONTROL setting menu state, the EEPROM setting menu state will be set.
When the STOP button of the Unit is pressed at each setting item display, the CONTROL setting menu state will be set.
CONTROL | contents:
bit 7 : High frequency superimpose ON/OFF (0 = OFF, 1 = ON) during recording
bit 6 to 4: Play start SD numbers (30 to 100 sectors, 10 sector-step) 0... ee Equation (n+3)x10 n=Oto7
bit 2 to 0 : High speed jump overrun amount (384 to 830 lines, 64 line-step) .... Equation (n+6)x64 n=Oto7
@ CONTROL 2 contents:
bits 4 to 0 : EEPROM version (From a) ..........ccccccscccessecesscceeseccessecesseeeessesesseeenseeees Equation n + 1,n=0 to 31, ASCII character conversion
@ When the REC button is pressed in the EJECT state, the unit will move to step 5. (Refer to 6.2.8 EJECT State)
6.2.5 TEST PLAY Mode
Setting Method Remarks Display
Test mode STOP state [ ts A Ae & |
Press the CHARACTOR button TEST PLAY menu [ TEST PLAY ]
of DISPLAY unit
Press the REC MODE button Playback start address setting (Cluster) [ ADRES 0032 ]
Press the PLAY/PAUSE button Continuous playback (Pit part) [s
Continuous playback (Groove part) [a
Press the STOP button of the Unit | TEST PLAY menu [ TEST PLAY ]
e : Address (Cluster), AAAA: Cl error
@ When the STOP button of the Unit is pressed during the TEST PLAY menu, the test mode STOP state will be set.
@ Press the <<, >» buttons of the Unit to change the settings at step 3.
* Pw button: Set the address to +01H.
* «<4 button: Set the address to -O1H.
41