Dreame DreameBot D10s Plus - Auto-Empty Robot Vacuum and Mop Manual

Safety Information

To avoid electric shock, fire or injury caused by improper use of the appliance, please read the user manual carefully before using the appliance and keep it for future reference.

Usage Restrictions

• This product should not be used by children younger than 8 years old nor persons with physical, sensory, intellectual deficiencies, or limited experience or knowledge without the supervision of a parent or guardian to ensure safe operation and to avoid any risks. Cleaning and maintenance shall not be performed by children without supervision.
• Children shall not play with this product. Ensure children and pets are kept at a safe distance from the robot while it is operating.
• If the power cord becomes damaged or broken, stop using it immediately and contact after-sales service.
• This product is for floor cleaning in a home environment only. Do not use it outdoors, on non-floor surfaces, or in a commercial or industrial setting.
• Do not use the robot in an area suspended above ground level without a protective barrier.
• Do not place the robot upside down. Do not use the LDS cover, robot cover, or bumper as a handle for the robot.
• Do not use the robot at an ambient temperature above 40°C or below 0°C or on a floor with liquids or sticky substances.
• Pick up any cables from the floor before using the robot to prevent it from dragging them while cleaning.
• Remove fragile or small items from the floor to prevent the robot from bumping into and damaging them.
• Keep hair, fingers, and other body parts away from the suction opening of the robots.
• To prevent damage or harm from dragging, clear any loose objects from the floor and remove cables or power cords along the cleaning path before operating the appliance.
• Keep the brush cleaning tool out of reach of children.
• Do not place children, pets, or any item on top of the robot regardless of whether it is stationary or moving.
• Do not use the robot to clean any burning objects. Do not use the robot to pick up flammable or combustible liquids, corrosive gases, or undiluted acids or solvents.
• Do not vacuum hard or sharp objects. Do not use the appliance to pick up objects such as stones, large pieces of paper or any item that may clog the appliance.
• Make sure the robot is turned off and the auto-empty base is unplugged before cleaning or performing maintenance.
• Do not use a wet cloth to wipe or any liquid to rinse the robot and auto-empty base.
  Washable parts must be dried completely before installing and using them. · Make sure the robot is turned off when being transported and kept in its original packaging if possible.
• Please use this product in accordance with the instructions in the User Manual. Users are responsible for any loss or damage that arise from improper use of this product.

Batteries and Charging

• Do not use any third-party battery or auto-empty base. Use only with RCS2 supply unit.
• Do not attempt to disassemble, repair, or modify the battery or auto-empty base on your own. Do not place the auto-empty base near a heat source.
• Do not use a wet cloth or wet hands to wipe or clean the base's charging contacts.
• Do not improperly dispose of old batteries. Unneeded batteries should be discarded at an appropriate recycling facility.
• If the robot will not be used for an extended period, fully charge it, then turn it off and store in a cool, dry place. Recharge the robot at least once every 3 months to avoid over-discharging the battery.
• This product contains batteries that can only be replaced by qualified technicians or after-sales service.

Laser Safety Information

• The laser sensor in this product meets the IEC 60825-1: 2014 Standard for Class 1laser products. Please avoid direct eye contact with it during use.

Accessories

Robot

Spot Cleaning Button

• Press briefly to start spot cleaning

Power/Clean Button

• Press and hold for 3 seconds to turn on or off
• Press briefly to start cleaning after the robot is turned on

Dock Button

• Press to send the robot back to the base
• Press and hold for 3 seconds to disable Child Lock

Status Indicator

• Solid White: Cleaning or cleanup is completed
• Blinking Orange: Error
• Solid Blue: Camera monitoring enabled

Robot Sensors

Auto-Empty Base

Status Indicator

• White: The base is plugged in
• Breathing White: Robot is charging
• Blinking Orange: The base has an error

Open the upper cover

Bottom

Back

Dust Bin

Mopping Module

Dust Collection Bag

Note: Due to the factory setting, a new dust collection bag has been installed inside already.

Preparing Your Home

Tidy up items such as power cords, cloths, slippers, and toys to improve the efficiency of the robot.

Open the door of the room to be cleaned, and put the furniture in its proper place to leave more space.

Before cleaning, place a physical barrier at the edge of the stairs and sofa to ensure smooth operation.

With the AI visual sensor, the robot can better recognize and avoid obstacles such as power cords, shoes, and socks. For best performance, make sure that all areas to be cleaned are well-lit.

Before Use

1. Remove the protective strips
   
2. Install the side brush
   

• Keep the immediate area 1.5 m in front of the base and 0.5 m to its both sides clear of objects.
• Make sure that no objects might block the signaling area.

About the Auto-Empty Base
It is recommended that the robot set out from the base before cleaning. Do not move the base while the robot is cleaning. This ensures that the robot returns to base smoothly. After the robot completes the cleaning task and automatically returns to the base, the base will start auto-empty. More settings can be operated on the app.

Connecting with the Dreamehome App

This product works with the Dreamehome app, which can be used to control your device.

1. Download the Dreamehome App
   Scan the QR code on the robot, or search "Dreamehome" in the app store to download and install the app based on your needs.
   
   

2. Add Device

Open the Dreamehome app, tap " " in the upper right, and then scan the QR code above again to add "DreameBot D10s Plus". Please follow the prompts to finish the Wi-Fi connection.

Note:

• Only 2.4 GHz Wi-Fi networks are supported.
• Due to upgrades in the app software, the actual operations may be different from the statements in this manual. Please follow the instructions based on the current app version.

3. Reset Wi-Fi
   Simultaneously press and hold the buttons and until you hear a voice say, "Waiting for the network configuration." Once the Wi-Fi indicator is blinking slowly, the Wi-Fi has been successfully reset.
   

Wi-Fi Indicator

• Blinking slowly: To be connected
• Blinking quickly: Connecting
• On: Connected

Note: If your robot cannot connect to the app successfully, reset the Wi-Fi and add the device again.

How to Use

Fast Mapping

After configuring the network for the first time, follow the instructions on the app to quickly create a map. The robot will start mapping without cleaning. When the robot returns to the base, the mapping process has been completed and the map will be saved automatically.

Turn On/Of

Press and hold the button for 3 seconds to turn on the robot. The power indicator should be illuminated. Place the robot onto the base. The robot should turn on automatically and begin charging. To turn off the robot, move the robot away from the base and press and hold the button for 3 seconds.

Start Cleaning

Press the button briefly to start cleaning after the robot is turned on. The robot will accurately map out a route, methodically clean along the edges and walls, then finish by cleaning each room in an S-shaped pattern to ensure a thorough job.

Pause/Sleep

When the robot is running, press any button to pause it. If the robot is paused for more than 10 minutes, it automatically enters sleep mode. All indicators on the robot will turn off. Press any button on the robot, or use the app to wake up the robot.

Note:

• The robot will turn off automatically if left in Sleep Mode for more than 12 hours.
• If the robot is paused and placed onto the base, the current cleaning task will end.

Do Not Disturb (DND) Mode

When the robot is set to the Do Not Disturb (DND) mode, the robot will be prevented from resuming cleaning and the power indicator goes out. The DND mode is disabled by default at the factory. You can use the app to enable the DND mode or modify the DND period. The DND period is 22:00-8:00 by default.

Note:

• The scheduled cleaning tasks will be performed on time during the DND period.
• The robot will resume cleanup where it left off after the DND period expires.

Spot Cleaning

When the robot is on standby, press briefly the button to enable the spot cleaning mode. In this mode, the robot cleans a squareshaped area of 1.5 × 1.5 meters around it and returns to its starting point once the spot cleaning is completed.

Scheduled Cleaning

You can schedule cleaning time in the Dreamehome app. The robot will automatically start cleaning at the designated time and then return to the base to recharge when the cleaning is done.

Additional App Functions

Follow the instructions on the app interface to use more functions. The version of the app might have been updated. Please follow the instructions based on the current app version.

Use the Mopping Function

It is recommended that all floors are vacuumed at least three times before the first mopping session to achieve a better cleaning effect.

1. Dampen the mop pad and wring out excess water. Install the mop pad as shown in the diagram.
   
2. Fill the tank with water.
   

Note:

• Do not use detergent or disinfectant.
• Do not fill the water tank with hot water as this may cause the water tank to warp.

3. Align the mopping module as indicated by the arrow, then slide it into the back of the robot until it clicks into place. Press the button or use the Dreamehome app to start cleaning.
   

Note:

• It is not recommended to use the mopping function on carpets.
• Use the app to adjust the water flow as required.

Parts

To keep the robot in good condition, it is recommended to refer to the following table for routine maintenance.

Note: The replacement frequency will depend on your usage of the robot. If an exception occurs due to special circumstances, the parts should be replaced.

Clean the Dust Bin and Filter

1. Open the robot cover and press the bin clip to remove the dust bin.
   
2. Open the bin cover and empty the bin as shown in the diagram.
   
3. Clean the auto-empty vent.
   
4. Remove the filter and tap its basket gently.
   
   Note: Do not attempt to clean the filter with a brush, finger, or any sharp objects so as to avoid damaging it.
5. Rinse the dust bin and filter with water and dry them completely before reinstalling.
   

Note:

• Rinse the dust bin and filter with clean water only. Do not use any detergent.
• Use the dust bin and filter only when they are completely dry.

Clean the Mopping Module

1. Slide the two release clips on the side of water tank to remove the mopping module, and then pull the mop pad off the mopping module.
   
2. Pour out the water in the tank. Clean with water only and leave to air dry before re-installing.
   
   Note: Do not directly expose the water tank to sunlight.
3. Clean the mop pad with water only and leave it to air dry before re-installing.
   

Note:

• Remove the pad from the mopping module before cleaning it. Make sure dirty water does not flow back into the water outlet to avoid clogging.

4. If the water flows too slowly or the outflow is not well-distributed, please clean the air hole on the cover of the water tank.
   

Clean the Main Brush

1. Press the brush guard clips inwards to remove the brush guard and lift the brush out of the robot.
   
2. Pull out the brush covers as shown in the diagram. Use the included cleaning tool to remove any hairs tangled in the brush.
   

Note: Do not pull out the hair tangled in the main brush too vigorously. Doing so may damage the brush.

Clean the Side Brush

Pull out the side brush and use the included cleaning tool to remove any hair tangled in the brush.

Clean the Main Wheel / Universal Wheel

Note: Use a tool such as a small screwdriver to separate the axle and tire of the universal wheel.

Note: Wet cloths can damage sensitive elements within the robot and base. Please use dry rags for cleaning.

Clean the LDS Laser Sensor

Clean the AI Visual Sensor

Clean the Charging Contacts and Auto-empty Vents

Clean the Cliff Sensor

Replace the Dust Collection Bag

According to the status indicator (blinking orange) and app prompts, replace the dust collection bag with a new one when it is full.

1. Discard the dust collection bag.
   

Note: When taking out the collection bag, close the bag handle to avoid dust leaking out.

2. Wipe the filter with a dry cloth.
   

Note: Do not close the base forcefully if the upper cover cannot be closed or the dust collection bag is not installed.

Clean the Air Duct

If the air duct is blocked, please clean it according to the following steps.

1. Unscrew mounting screws on the air duct cover and remove the cover plate.
   
2. Check whether the air duct is blocked by foreign objects. If any, clean them.
   
3. Reinstall the air duct cover as shown in the diagram.
   

Robot Restarting

If the robot stops responding or cannot be turned off, press and hold down the button for 10 seconds to forcefully turn it off. Then press and hold the button for 3 seconds to turn the robot on.

Battery

The robot contains a high-performance lithium-ion battery pack. Please ensure that it remains well-charged for daily use to maintain optimal battery performance. If the robot is not used for an extended period of time, turn it off and put it away. To prevent damage from over-discharging, the robot should be recharged at least once every three months.

Troubleshooting

For additional services, please contact us via aftersales@dreame.tech
Website: https://global.dreametech.com

Specifications

Robot

Model	RLS6AD
Charging Time	Approx. 6 hours
Rated Voltage	14.4 V
Rated Power	46 W
Operation Frequency	2400-2483.5 MHz
Maximum Output Power

Auto-Empty Base

Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

Battery Disposal and Removal

The built-in lithium-ion battery contains substances that are hazardous to the environment. Before disposing of the battery, make sure the battery is removed by qualified technicians and discarded at an appropriate recycling facility.

• the battery must be removed from the appliance before it is scrapped;
• the appliance must be disconnected from the supply mains when removing the battery;
• the battery is to be disposed of safely.

• Before removing the battery, disconnect the power and run out the battery as much as possible.
• Unneeded batteries should be discarded at an appropriate recycling facility.
• Do not expose to high temperature environment to avoid risks of explosion.
• Under abusive conditions, liquid may be ejected from the battery. If contact occurs, flush with water and seek medical help.

Removal Guide

1. Turn over the robot, use a proper tool to remove the screws on the back of the robot, and then remove the cover.
2. Unplug the terminals between the battery and PCB board to remove the battery.

For more support, contact us via aftersales@dreame.tech

Website: https://global.dreametech.com

Manufactured by: Dreame Trading (Tianjin) Co., Ltd. Made in China