Vaporesso TARGET 80 - Pod Mod Kit Manual
  1. Manuals
  2. Brands
  3. Vaporesso Manuals
  4. Vaporizers
  5. Target 80
  6. User manual

Vaporesso TARGET 80 - Pod Mod Kit Manual

Also See for TARGET 80:

Advertisement

Table of Contents
Contents
Vaporesso TARGET 80 - Pod Mod Kit Manual

SPECIFICATIONS

Dimensions: 130.9 x 38.3 x 30.8mm
POD Capacity: 5ml/2ml(TPD)
Coils & Suggested Wattage:
GTX 0.2Ω MESH Coil (45-60W)
GTX 0.3Ω MESH Coil (32-45W)
Battery Capacity: 3000mAh
Output Power: 5-80W
Charging Current: DC 5V/2A,Type-C
Battery Display: 0.96'' TFT Screen

PACKING LIST

1 x TARGET 80 MOD
1 x GTX PODTANK 26 (5ml/2ml TPD)
1 x GTX 0.2Ω MESH Coil (In-BOX)
1 x GTX 0.3Ω MESH Coil (In-BOX)
1 x Type-C Cable
1 x User Manual
1 x Warranty Card

EXPLODED VIEW

EXPLODED VIEW

USE INSTRUCTIONS

Install the Tank

Install the tank to the battery by screwing the 510 thread. Make sure they are firmly connected.

Replace the Coil

Replacing the Coil

  • Place the drip tip of the pod face down, and pull out the used coil;
  • Install a new coil to the pod;
  • Press the coil to align the coil base with the pod.

Fill E-liquid

Filling the E-liquid

  • Unscrew the top cap from the pod;
  • Fill e-liquid through the filling slot;
  • Screw the top cap to reinstall it back into place as shown;
  • Please wait 5 minutes for the e-liquid to soak into the coil completely.

Adjust the Airflow

Please rotate the pod to match the air-inlet port to adjust the airflow volume.

Power On/Off the Device

Power on/off: press the power button 5 times in 2s.

Power Adjustment

TARGET 80 Kit is using the powerful GTX coil platform, and the suggested power need to be noticed before start vaping.

GTX MESH Coils GTX 0.2Ω MESH GTX 0.3Ω MESH
Suggested Power 45-60W 32-45W

Start Vaping

Press the power button to enjoy extraordinary vaping experience.

Charge the Battery

After connecting the Type-C cable to the battery, the battery indicator and remaining charging time will be showed on the screen.

Lock or unlock the device

Press the fire button 3 times, then the +, - and mode buttons will be locked. In the same way, the buttons will be unlocked and the screen will be unlocked.

Choose a Mode

  1. Long press the mode button for main mode selection (Pulse Mode/F(t) Mode/VWN Mode).
  2. Press the mode button 3 times continuously for secondary menu setting.


*F(t): F(t) MODE (DEFAULT)
F(t) MODE is by adjusting temperature, heating speed and time, F(t) mode releases the flavors of e-liquid adequately, delivering the perfect balanced tasting experience consistently from the first puff throughout.


*DIY: DIY MODE
You can choose traditional VW (H, N, S), VV, BP (Bypass) modes in this section.


*PUL: PULSE MODE (DEFAULT)
PULSE MODE: It's a mode to improve vaping experience through constant voltage output, delivering optimal flavor production, throat hit, nicotine satisfaction, and perfect temperature cloud continuously.


*SET: SYSTEM SET
System setting includes DEFAULT, SMART VW, PUFF, and VERSION options.
SMART VW: when this function is turned on and a POD is installed, the system will recommend the best power.

PROTECTIONS

  1. Short circuit protection & Low resistance protection:
    When the load resistance is less than 0.1±0.01Ω, press power button could trigger the short circuit protection or Low resistance protection, the device will close the output, at the same time OLED display will show "SHORT ATOMIZER".
  2. No load protection:
    When no load resistance is detected, press power button could trigger the no load protection, the device will close the output, at the same time OLED display will show "CHECK ATOMIZER".
  3. High resistance protection:
    When the load resistance is greater than 5±0.5Ω, press power button could trigger the high resistance protection, the device will close the output, at the same time OLED display will show " CHECK ATOMIZER ".
  4. Low voltage protection:
    When the voltage of the battery cell is lower than 3.3±0.1V, press power button could trigger the low voltage protection, the device will close the output, at the same time OLED display will show "LOW BATTERY".
  5. PCBA(Printed Circuit Board Assembly):
    When the temperature of the PCBA(Printed Circuit Board Assembly) temperature sensor is higher than 70+5℃/-10℃, press power button could trigger the PCBA (Printed Circuit Board Assembly) over heat protection, the device will close the output, at the same time OLED display will show "OVER HEAT".
  6. Over discharge protection:
    During the process of smoking, when the battery cell voltage is lower than 2.9±0.1 V, the device will close the output automatically.
  7. Over charge protection:
    During charging, when the battery cell voltage is greater than 4.1±0.1V, OLED display will show "100%". At the end of charging, battery cell voltage will not exceed 4.2±0.03V.
  8. Auto-shut off protection:
    When POWER button is held for 10±1 seconds, the device will close the output, at the same time OLED display will show "OVER TIME".
  9. Battery cell anti-reverse connection protection:
    The inversion of battery cell will not damage the battery.

CAUTIONS

  1. Please turn off the device when it is not in use.
  2. Do not leave the charging device unattended.
  3. Do not drop, throw or abuse your device, which may cause damage.
  4. Please use a standard USB output charger with proper charging current and voltage range.
  5. Keep away from the water or any flammable gas, liquid.
  6. Do not expose the device to direct sunlight, dust, moisture or mechanical shock.
  7. Do not expose the device to extreme temperature. (Recommended temperature range: -10~60℃ /14~140℉ while using and -10~45℃ /14~113℉ while storing).
  8. EEE Recycling: the product should not be treated as household waste, instead, it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
  9. Battery Recycling: the product battery should not be treated as household waste, instead, it should be handed over to the applicable used battery collection point for recycling.
  10. Only have your device repaired by Vaporesso. Do not attempt to repair it by yourself as damage or personal injury may occur.

WARNINGS

This refillable electronic cigarette is intended for use with compatible e-liquid, which may contain nicotine. Nicotine is an addictive substance and it is not suitable or recommended to use in following cases:

  1. This device is not suitable for:
    • Persons under the legal smoking age.
    • Persons experiencing heart disease, stomach or duodenal ulcers, liver or kidney problems, long-term throat disease or difficult breathing due to bronchitis, emphysema or asthma.
    • Persons with an overactive thyroid gland or experiencing phaeochromocytoma (a tumour of the adrenal gland that can affect blood pressure).
    • Persons taking certain medications like Theophylline, Ropinirole or Clozapine and etc..

If there is any additional requirement about this product, please consult the local agent or contact us through our website: www.vaporesso.com

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Vaporesso TARGET 80 - Pod Mod Kit Manual

Advertisement

Need help?

Need help?

Do you have a question about the TARGET 80 and is the answer not in the manual?

Questions and answers

Related Manuals for Vaporesso TARGET 80

Save Article as PDF

Table of Contents