Sealey AP6310.V2 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT
IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these units.
‰
WARNING! Use the Rollcab on level and solid ground, preferably concrete.
‰
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep the units clean and tidy in accordance with good workshop practice.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use these units for any purpose other than that for which they are designed.
8
DO NOT use the units outdoors.
8
DO NOT place the units in a damp or wet location or an area where there is condensation.
8
DO NOT clean the units with any solvents which may damage the surfaces or the protective coating.
8
DO NOT move the units with the drawers out. To avoid tipping, open one drawer at a time and close and secure all drawers whilst
8
moving the rollcab.
DO NOT step on the drawers.
8
DO NOT overload the drawers, weight limit per drawer is 36kg.
8
2. INTRODUCTION
All heavy-duty steel construction and manufactured with steel inner walls for extra strength and durability. Heavy-duty 45mm ball-
bearing drawer slides provide superior performance, suitable for heavier loads. Full height rear locking mechanism, locks smooth
running soft close drawers in place. Rust and solvent resistant black crinkle effect finish. Fitted with six Ø125mm PP wheels with black
chrome effect alloys, two fixed, two swivel and two swivel with brakes. Each drawer features stylish black anodized heavy-duty drawer
pulls plus pre-cut non-slip liners. Power tool charging drawer fitted with 4 x 230V sockets and 2 x 5V 2.4A USB sockets. Mounting
points to fit additional four gang power strip - Model No. EL34USBB (not included). Stainless steel 'flip-top' split equally into 2-sections
providing a work surface and additional storage. Two cylinder locks allow drawers and power tool charging drawer to be locked
separately.
3. SPECIFICATION
Model No: ................................................ AP6310BE.V2
Overall Size (W x D x H): .............. 1600 x 584 x 988mm
Top Compartment (x2):
Overall Size (W x D x H): ...................720 x 465 x 70mm
Small Section (W x D x H): .................720 x 200 x 70mm
Large Section (W x D x H): ................720 x 280 x 70mm
Power Tool Charging Area:
Overall Size (W x D x H): .................485 x 335 x 390mm
Top Section (W x D x H): ..................485 x 335 x 150mm
Bottom Section (W x D x H): ...............485 x 335 375mm
4. CONTENTS
ITEM DESCRIPTION
1 Bolt M6 x 16 mm
2 Handle fig.1
3 Storage hooks fig.2
4 Bolt M3 x 10 mm (not shown)
5 Bottle opener fig.4
5. ASSEMBLY
5.1. These units are heavy, obtain the help of at least one other person before attempting to unpack them.
5.2. Mount the side mounted handle onto the left hand end of cabinet and attach with 4 bolts (item 1) (fig.1).
5.3. Mount the storage hooks using bolts (item 1) at each end of the cabinet (fig.2) or alternatively mount one set of hooks on reverse face
of either left or right hand end of cabinet (fig.2).
5.4. To remove a drawer with roller sliders, pull the drawer completely out, press down the right tab and lift up the left tab, pull drawer off the
slides To reinstall the drawer, realign with the internal drawer slide and push until it locks in place (fig.3).
5.5. Fit bottle opener to the left hand (handle) end of the cabinet using two M6 x 16 mm bolts.(fig.4).
© Jack Sealey Limited
MOBILE TOOL CABINET 1600MM WITH POWER
TOOL CHARGING DRAWER
AP6310BE.V2
MODEL NO:
QTY
14
1
4
4
1
Original Language Version AP6310.V2 Issue 2 (H,3,F) 25/09/23