Advertisement
Quick Links
Quad Track Kit
RT1200 Trencher
Model No. 25429
Model No. 25429E
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Bottom kingpin
Socket-head bolt (14 x 40 mm)
Kingpin shim—0.005 inch (optional)
Kingpin shim—0.010 inch (optional)
Kingpin shim—0.015 inch (optional)
Socket-head bolt
Grease fitting (90° elbow)
Nipple
Coupler
Grease fitting
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
–
4
4
8
8
8
12
4
4
4
4
Form No. 3403-231 Rev A
Installation Instructions
Use
Prepare the machine.
Install the bottom kingpin.
Install the grease fitting on the
frame-mount bracket.
Original Instructions (EN)
All Rights Reserved *3403-231* A
Printed in the USA
Advertisement
Related Manuals for Toro 25429
Summary of Contents for Toro 25429
- Page 1 Form No. 3403-231 Rev A Quad Track Kit RT1200 Trencher Model No. 25429 Model No. 25429E Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
- Page 2 Procedure Description Qty. Top mounting plate (front, left or rear, right) Top mounting plate (front, right or rear, left) Frame-mount bracket (front, left or rear, right) Frame-mount bracket (front, right or rear, left) Mounting-plate shim (16 gauge) Mounting-plate shim (26 gauge) Bolt (16 x 60 mm) Install the frame-mount bracket, top Bolt (14 x 70 mm)
-
Page 3: Preparing The Machine
Procedure Description Qty. Sprocket third Bolt (16 x 40 mm) Washer Install the sprocket thirds and the track. Hex nut (16 mm) Track – No parts required Check and adjust the toe of the tracks. – No parts required Align the tracks. –... - Page 4 Installing the Bottom Kingpin Parts needed for this procedure: Bottom kingpin Socket-head bolt (14 x 40 mm) Kingpin shim—0.005 inch (optional) Kingpin shim—0.010 inch (optional) Kingpin shim—0.015 inch (optional) Socket-head bolt Procedure 1. Remove any paint and clean the upper and lower surfaces on the hub in the locations shown in Figure g037890...
- Page 5 Installing the Grease Fitting on the Frame-Mount Bracket Parts needed for this procedure: Grease fitting (90° elbow) Nipple Coupler Grease fitting Procedure Assemble the grease-fitting components and install the assembly into the frame-mount bracket as shown in Figure g037959 g037589 Figure 4 Rear (above) and Bottom (below) Views of the Hub Figure 5...
- Page 6 Installing the Frame-Mount Bracket, Top Mounting Bracket, and Bolt Stops Parts needed for this procedure: Top mounting plate (front, left or rear, right) Top mounting plate (front, right or rear, left) Frame-mount bracket (front, left or rear, right) Frame-mount bracket (front, right or rear, left) Mounting-plate shim (16 gauge) Mounting-plate shim (26 gauge) Bolt (16 x 60 mm)
- Page 7 g037541 Figure 8 Bottom View of Hub 1. Hub face 2. Edge of the tube on the frame-mount bracket 5. Torque the 2 bolts (14 x 55 mm) and 2 bolts (14 x 30 mm) to 135 to 165 N∙m (100 to 120 ft-lb). Installing the Top Mounting Bracket g037910 1.
- Page 8 Installing the Bolt Stops Install the 2 bolts (14 x 40 mm), 2 jam nuts (14 mm), 2 bolts (16 x 70 mm), 2 jam nuts (16 mm), and 2 locknuts (16 mm) into the frame-mount bracket from the inboard side as shown Figure g03791 1 Figure 10...
- Page 9 Installing the Direction Limiter Parts needed for this procedure: Direction limiter Direction-limiter shim (16 gauge) Direction-limiter shim (18 gauge) Direction-limiter shim (26 gauge) Shim (11 gauge) g037960 Shim (16 gauge) Shim (18 gauge) Shim (26 gauge) Threaded rod Hex-head bolt (12 x 130 mm) Jam nut (16 mm) Figure 11 Flat washer (16 mm)
- Page 10 Installing the Bolt Locking Plates Parts needed for this procedure: Bolt locking plate (16 mm) Bolt locking plate (14 mm) Lockwasher (10 mm) Bolt (10 x 20 mm) Procedure 1. Install the 4 bolt locking plates (16 mm) and 4 bolt locking plates (14 mm) over the bolts securing the top mounting bracket to the frame-mount bracket using the hardware shown in...
- Page 11 Installing the Chassis Frame Parts needed for this procedure: g037597 Figure 15 Chassis frame Only the outer tracker adjuster is shown. Pivot axle 1. Track-adjuster bolt (2) Pivot-axle plate Spacer 3. Install the chassis frame onto the frame-mount bracket Retaining ring using the pivot axle (Figure 16).
- Page 12 Installing the Sprocket Thirds and the Track Parts needed for this procedure: Sprocket third Bolt (16 x 40 mm) Washer Hex nut (16 mm) Figure 18 Track 1. Nut 3. Wheel lug 2. Sprocket third Procedure 1. Align the 3 sprocket thirds together on the floor Note: It is easier to slide the sprocket third between (Figure 17).
- Page 13 Checking and Adjusting the Toe of the Tracks No Parts Required Procedure Figure 19 Note: Check to ensure that the centerlines of the tracks on The final sprocket third is not shown for the purpose of each axle are approximately parallel, without toe-in or toe-out. clarity.
- Page 14 Aligning the Tracks No Parts Required Procedure To determine whether the tracks are correctly aligned, start the engine, rotate the track at least 6 times, and check whether the wheels remain centered between the teeth of the track (Figure 22). Note: The wheels should remain centered between the teeth of the track.
- Page 15 3. Repeat this procedure until the wheels remain centered between the teeth of the track. Checking the Tension of the Tracks g037558 No Parts Required Figure 25 Procedure 1. Gap—83 to 89 mm (3-1/4 2. Round bar to 3-1/2 inches) Important: It is normal for the tracks to stretch the first time that you use them.
- Page 16 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.