Sealey GSA634.V2 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
Follow all workshop safety rules, regulations, and conditions when using wrench.
9
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
WARNING! DO NOT use wrench if damaged or thought to be faulty. Contact Service Agent.
‰
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Un-authorised parts may be
9
dangerous and will invalidate the warranty.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
9
secure.
Wear approved safety eye/face shield, ear defenders and hand protection.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
9
DO NOT use the wrench for a task it is not designed to perform.
8
DO NOT use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry wrench with your hand on power trigger, in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
‰
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. INTRODUCTION
Generation Series compact air ratchet wrench. Contoured handle to insulate user from chill and vibration. Finger operated trigger and textured
grip allows added control, even with greasy hands. Ideal for working in engine bays or other places with restricted access.
3. SPECIFICATION
MODEL: ......................................... GSA634.V2, GSA635.V2
Air Consumption: ........................................................... 4cfm
Drive: .......................................................................1/4", 3/8"
Free Speed: ............................................................... 180rpm
Length: ....................................................................... 185mm
Maximum Torque:............................................. 20lb.ft(27Nm)
Noise Power/Pressure: ...................................... 100/89dB(A)
Operating Pressure: ...................................................... 90psi
Vibration/Uncertainty: ......................................... 2.5/1.25m/s²
4. PREPARATION
4.1. AIR SUPPLY (Recommended hook-up procedure is shown in fig 1.)
4.1.1. Ensure wrench air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the wrench. Too high an air pressure and unclean
‰
air will shorten the product life owing to excessive wear, and may be dangerous, causing damage and/or personal injury.
4.1.3. Drain the air tank daily. Water in the air line will damage the wrench.
4.1.4. Clean air inlet filter weekly.
4.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
4.2. COUPLINGS: Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome this, connect a
leader hose to the wrench. A quick change coupling may then be used to connect the leader hose to the air line recoil hose.
© Jack Sealey Limited
1/4"& 3/8" SQ DRIVE COMPACT AIR RATCHET
WRENCH
GSA634.V2, GSA635.V2
MODEL NO'S:
Wear protective Wear ear
gloves protection
Original Language Version
Wear a mask
fig.1
GSA634.V2, GSA635.V2 Issue: 2 (3) 05/01/22
fig.2