Sealey GSA53 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
‰
‰ ‰ WARNING!‰Disconnect from air supply before changing accessories or servicing.
‰
‰
‰ ‰ maintain the tool in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
‰
dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
‰ ‰ Wear approved safety eye/face shield, ear defenders and hand protection.
9
‰
‰ ‰ maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
‰
‰ ‰ Keep children and non essential persons away from the working area.
9
‰
‰ ‰ DO NOT use the tool for a task it is not designed to perform.
‰ 8
WARNING! DO NOT use tool if damaged or thought to be faulty. Contact a Sealey service agent.
‰
‰ ‰ DO NOT use tool unless you have been instructed in its use by a qualified person.
‰ 8
‰ ‰ DO NOT carry the tool by the air hose, or yank the hose from the air supply.
‰ 8
‰ ‰ DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.
‰ 8
‰ ‰ DO NOT carry tool with your hand on the power trigger in order to avoid unintentional starting.
‰ 8
‰ ‰ DO NOT direct air from the air hose at yourself or others.
‰ 8
‰ ‰ When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
‰
2. INTRODucTION
Generation air shears feature contoured and insulated handle to protect operator from the effects of vibration and chill. Smooth operating
mechanism suitable for cutting straight lines in sheet metal up to 1.2mm thickness.
3. SpEcIFIcATION
model no .....................................................................GSA53
max. cutting capacity ........................................ 1.2mm (steel)
Inlet size ...................................................................1/4" BSP
Air consumption ............................................................. 6cfm
Operating pressure ....................................................... 90psi
Noise power/pressure ........................................ 106/95dB(A)
Vibration/uncertainty ........................................ 2.71/0.76m/s²
Weight ........................................................................... 1.0kg
Consumables:
Replacement blade outer left .................................GSA53.34
Replacement blade outer right ...............................GSA53.37
Replacement blade centre .....................................GSA53.35
4. pREpARATION
4.1. AIR SupplY
4.1.1. Recommended hook-up procedure is shown in fig.1.
4.1.2. Ensure tool valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.3. You will require an air pressure of 90psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the tool. Too high an air pressure and/or
‰
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the tool.
4.1.5. Clean air inlet filter weekly.
4.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 meters). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
© Jack Sealey Limited
AIR SHEARS
mODEL NO:
Wear ear Wear hand
protection protection
Original Language Version
GSA53
GSA53 | Issue:5 (H,3,F) 10/05/19